SIGLENT TECHNOLOGIES SDG1062X User manual

User Manual
SDG1000X Series Function/Arbitrary Waveform Generator
UM0201X-E01D
2017 SIGLENT TECHNOLOGIES CO., LTD

SIGLENT
SDG1000X User Manual I
Declaration
Copyright © SIGLENT TECHNOLOGIES CO., LTD. All rights reserved.
Without permission, contents in this manual are not allowed to be copied,
extracted or translated.

SIGLENT
II SDG1000X User Manual
General Safety Summary
Carefully read the following safety precautions to avoid any personal injuries
or damages to the instrument and any product connected to it. To avoid
potential hazards, please use the instrument as specified.
Only qualified technical personnel should service this instrument.
Avoid fire or open flame.
Use properly rated power line connections.
Use only the specified power line which has been approved by your local
regulatory agency.
Ground the Instrument.
The instrument is grounded through the protective ground conductor of the
power line. To avoid electric shock, the ground conductor must be connected
to the earth ground. Make sure the instrument is grounded correctly before
connecting its input or output terminals.
Connect the signal wire correctly.
The potential of the signal wire ground is equal to the earth, therefore do not
connect the signal wire to a high voltage. Do not touch the exposed contacts
or components.
Observe all terminal ratings.
To avoid fire or electric shock, please observe all ratings and sign instructions
on the instrument. Before connecting the instrument, please read the manual
carefully to gain more information about the ratings.
Do not operate with suspected failures.
If you suspect that the product is damaged, please let only qualified service
personnel check it.
Avoid circuit or wire exposure.
Do not touch exposed contacts or components when the power is on.
Do not operate in wet/damp conditions.
Do not operate in an explosive atmosphere.
Keep the surface of the instrument clean and dry.

SIGLENT
SDG1000X User Manual III
Safety Terms and Symbols
Terms used on the instrument. Terms may appear on the instrument:
DANGER: Indicates an injury or hazard that may immediately happen.
WARNING: Indicates an injury or hazard that may not immediately happen.
CAUTION: Indicates that a potential damage to the instrument or other
property might occur.
Symbols used on the instrument. Symbols may appear on the instrument:
Hazardous Protective Warning Chassis Power
Voltage Earth Ground Ground Switch

SIGLENT
IV SDG1000X User Manual
Introduction to SDG1000X
The manual covers the following 2 models of SDG1000X Series
Function/Arbitrary Waveform Generators: SDG1032X and SDG1062X.
SIGLENT‘s SDG1000X is a series of dual-channel function/arbitrary waveform
generators with specifications of up to 60MHz maximum bandwidth, 150MSa/s
sampling rate and 14-bit vertical resolution. The proprietary EasyPulse
technology helps to solve the weaknesses inherent in traditional DDS
generators when generating pulse waveforms, and the special square wave
generator is capable of generating square waveforms with up to 60MHz
frequency and low jitter. With these advantages, the SDG1000X can provide
users with a variety of high fidelity and low jitter signals and can meet the
growing requirements of complex and extensive applications.
Key Features
Dual-channel，with bandwidth up to 60MHz and amplitude up to 20Vpp
150MSa/s sampling rate, 14-bit vertical resolution, and 16kpts waveform
length
Innovative Easy Pulse technology, capable of generating lower jitter Pulse
waveforms, brings a wide range and extremely high precision in pulse
width and rise/fall times adjustment
Special circuit for Square waves, which can generate Square wave with
frequencies up to 60MHz and jitter less than 300ps+0.05ppm of period
Avariety of analog and digital modulation types: AM、DSB-AM、FM、PM、
FSK、ASK 、PSK and PWM
Sweep and Burst functions
Harmonic waveforms generating function
Waveforms combining function

SIGLENT
SDG1000X User Manual V
High precision Frequency Counter
196 kinds of built-in arbitrary waveforms
Standard interfaces: USB Host, USB Device（USBTMC）, LAN（VXI-11）
Optional interface: GPIB
4.3‖ display

SIGLENT
VI SDG1000X User Manual
Catalog
General Safety Summary................................................................................II
Introduction to SDG1000X ............................................................................ IV
1Quick Start................................................................................................1
1.1 Handle Adjustment .......................................................................2
1.2 The Front/Rear Panel...................................................................3
1.3 To Select a Waveform...................................................................8
1.4 To Set Modulation/Sweep/Burst..................................................12
1.5 To Turn On/Off Output ................................................................14
1.6 To Use Numeric Input.................................................................15
1.7 To Use Common Function Keys.................................................16
2Front Panel Operations...........................................................................17
2.1 To Set Sine Waveform................................................................18
2.2 To Set Square Waveform............................................................23
2.3 To Set Ramp Waveform..............................................................26
2.4 To Set Pulse Waveform..............................................................28
2.5 To Set Noise Waveform..............................................................32
2.6 To Set DC Waveform..................................................................35
2.7 To Set Arbitrary Waveform..........................................................36
2.8To Set Harmonic Function ..........................................................45
2.9 To Set Modulation Function........................................................48
2.9.1 AM........................................................................................49
2.9.2 DSB-AM...............................................................................52
2.9.3 FM........................................................................................54
2.9.4 PM........................................................................................56
2.9.5 FSK......................................................................................58
2.9.6 ASK......................................................................................60
2.9.7 PSK......................................................................................61
2.9.8 PWM ....................................................................................63
2.10 To Set Sweep Function...............................................................66
2.11 To Set Burst Function.................................................................71
2.12 To Store and Recall....................................................................77
2.12.1 Storage System .............................................................78

SIGLENT
SDG1000X User Manual VII
2.12.2 File Type ........................................................................79
2.12.3 File Operation ................................................................81
2.13 To Set Utility Function.................................................................85
2.13.1 System Settings.............................................................87
2.13.2 Test/Cal..........................................................................95
2.13.3 Frequency Counter ........................................................99
2.13.4 Output..........................................................................102
2.13.5 CH Copy/Coupling .......................................................105
2.13.6 Remote Interface .........................................................110
2.13.7 Sync Output.................................................................116
2.13.8 Clock Source................................................................118
2.13.9 Mode............................................................................119
2.13.10 Overvoltage Protection.................................................121
3Examples..............................................................................................122
3.1 Example 1: Generate a Sine Waveform ...................................123
3.2 Example 2: Generate a Square Waveform...............................125
3.3 Example 3: Generate a Ramp Waveform.................................127
3.4 Example 4: Generate a Pulse Waveform..................................129
3.5 Example 5: Generate a Noise ..................................................131
3.6 Example 6: Generate a DC Waveform .....................................132
3.7 Example 7: Generate a Linear Sweep Waveform.....................133
3.8 Example 8: Generate a Burst Waveform..................................135
3.9 Example 9: Generate an AM Modulation Waveform.................137
3.10 Example 10: Generate a FM Modulation Waveform.................139
3.11 Example 11: Generate a PM Modulation Waveform.................141
3.12 Example 12: Generate a FSK Modulation Waveform...............143
3.13 Example 13: Generate an ASK Modulation Waveform.............145
3.14 Example 14: Generate a PSK Modulation Waveform...............147
3.15 Example 15: Generate a PWM Modulation Waveform .............149
3.16 Example 16: Generate a DSB-AM Modulation Waveform........151
4Troubleshooting ....................................................................................153
4.1 General Inspecting ...................................................................153
4.2 Troubleshooting........................................................................154
5Service and Support .............................................................................155

SIGLENT
VIII SDG1000X User Manual
5.1 Maintenance summary.............................................................155
5.2 Contact SIGLENT.....................................................................156
6Appendix...............................................................................................157
Appendix A: Accessories......................................................................157
Appendix B: Daily Maintain and Cleaning............................................158

SIGLENT
SDG1000X User Manual 1
1 Quick Start
This chapter covers the following topics:
Handle Adjustment
The Front/Rear Panel
To Select a Waveform
To Set Modulation/Sweep/Burst
To Turn On/Off Output
To Use Numeric Input
To Use Common Function Keys

SIGLENT
2 SDG1000X User Manual
1.1 Handle Adjustment
To adjust the handle position of the SDG1000X, please grip the handle by the
sides and pull it outward. Then, make the handle rotate to the desired position.
Figure 1-1 Viewing Position and Carrying Position

SIGLENT
SDG1000X User Manual 3
1.2 The Front/Rear Panel
This chapter will provide a brief introduction and description for the operation
and functions of the front/rear panel.
Front Panel
SDG1000X has a clear and simple front panel which includes a 4.3 inch
screen, menu softkeys, numeric keyboard, knob, function keys, arrow keys,
and channel control area.
Figure 1-2 Front Panel of SDG1000X
USB
Host
Numeric Keyboard
Knob
Power
Key
User Interface
Menu
Softkeys
Function
Keys
Channel
Control
Arrow
Keys

SIGLENT
4 SDG1000X User Manual
Rear Panel
The rear panel provides multiple interfaces, including Counter, 10MHz In/Out,
Aux In/Out, LAN, USB Device, Earth Terminal and AC Power Supply Input.
Figure 1-3 Rear Panel of SDG1000X
Aux
In/Out
10 MHz Clock Input/Output
Earth Terminal
LAN Interface
USB Device
AC Power Supply
Input
Counter

SIGLENT
SDG1000X User Manual 5
User Interface
The SDG1000X can only display parameters and waveform information for
one channel at a time. The picture below shows the interface when CH1
chooses AM modulation of a sine waveform. The information displayed may
vary depending on the function selected.
Figure 1-4 User Interface
1. Waveform Display Area
Displays the currently selected waveform of each channel.
2. Channel Status Bar
Indicates the selected status and output configuration of the channels.
3. Basic Waveform Parameters Area
Shows the current waveform‘s parameters of each channel. Press Parameter
and select the corresponding softkey to highlight the parameter to configure.
Then use number keys or knob to change the parameter value.
4
3
8 7 6 5
1 2

SIGLENT
6 SDG1000X User Manual
4. Channel Parameters Area
Displays the load and output settings of the currently selected channel.
Load ----Value of the output load, as selected by the user.
Press Utility → Output → Load, then use the softkeys, number keys or knob to
change the parameter value; or continue pressing the corresponding output
key for two second to switch between High Impedance and 50Ω.
High Impedance: display HiZ.
Load: display impedance value (the default is 50Ω and the range is 50Ω to
100kΩ).
Note: This setting does not actually change the instrument‘s output impedance
of 50Ω but rather is used to maintain amplitude accuracy into different load
values.
Output ----Channel output state.
After pressing corresponding channel output control port, the current channel
can be turned on/off.
5. LAN Status Icon
SDG1000X will show different prompt messages based on the current network
status.
This mark indicates LAN connection is successful.
This mark indicates there is no LAN connection or LAN connection is
unsuccessful.
6. Mode Icon
SDG1000X will show different prompt messages based on the current mode.
This mark indicates current mode is Phase-locked.
This mark indicates current mode is Independent.
7. Menu
Shows the menu corresponding to the displayed function. For example, Figure

SIGLENT
SDG1000X User Manual 7
1-4 shows the parameters of ―AM modulation‖.
8. Modulation Parameters Area
Shows the parameters of the current modulation function. After selecting the
corresponding menu, use number keys or knob to change the parameter
value.

SIGLENT
8 SDG1000X User Manual
1.3 To Select a Waveform
Press Waveforms to enter the menu as Figure 1-5 shows. The example below
will help familiarize with the waveform selection settings.
Figure 1-5 Waveform Selections
1. Press Waveforms key and then press Sine softkey. The SDG1000X can
generate sine waveforms with frequencies from 1μHz to 60MHz. By
setting Frequency/Period, Amplitude/High level, Offset/Low level and
Phase, a sine waveform with different parameters can be generated.
Figure 1-6 Sine Display Interface
2. Press Waveforms key and then press Square softkey. The generator can
generate square waveforms with frequencies from 1μHz to 60MHz and
variable duty cycle. By setting Frequency/Period, Amplitude/High level,
Offset/Low level, Phase and DutyCycle, a square waveform with different
parameters can be generated.

SIGLENT
SDG1000X User Manual 9
Figure 1-7 Square Display Interface
3. Press Waveforms key and then press Ramp softkey. The generator can
generate ramp waveforms with frequencies from 1μHz to 500kHz and
variable symmetry. By setting Frequency/Period, Amplitude/High level,
Offset/Low level, Phase and Symmetry, a ramp waveform with different
parameters can be generated.
Figure 1-8 Ramp Display Interface
4. Press Waveforms key and then press Pulse softkey. The generator can
generate pulse waveforms with frequencies from 1μHz to 12.5 MHz and
variable pulse width and rise/fall times. By setting Frequency/Period,
Amplitude/High level, Offset/Low level, PulWidth/Duty, Rise/Fall and Delay,

SIGLENT
10 SDG1000X User Manual
a pulse waveform with different parameters can be generated.
Figure 1-9 Pulse Display Interface
5. Press Waveforms key and then press Noise softkey. The generator can
generate noise with a 60MHz bandwidth. By setting Stdev and Mean,
noise with different parameters can be generated.
Figure 1-10 Noise Display Interface
6. Press Waveforms key and then press Page 1/2, last press the DC softkey.
The generator can generate a DC signal with a level up to ±10V into a
HighZ load or ±5V into a 50Ω load.