Sigma NPS-08 User manual

User Manual
Unmanaged AiPoE Switch
www.sigmasec.gr

8FE PoE+2FE UP-Ai , 8*10/100M PoE port+2*100M Uplink port
Features
Overview
1
Product Display
2
Accessories List
Function Switch
Mark Mode Description
N
V
S
Standard Normal
Port Isolation
Ultral-far Mode
All ports communicate freely,adapting to common data transmission environment
Switch to VLAN mode;downlink isolating from each other,uploads and downloads data
through uplink;suppress network failure like broadcast storm and virus attack
Downlink speed limitation:10M(Ultral-far transmission:250 meters)
Indicator
Status
Always ON
Always OFF
Flashes
Port circuit or cunrrent over-loaded
Port Isolation LED：V
Ultral-far Mode LED：S
Port Isolation mode ON
Ultral-far mode ON
PoE LED
Orange
Green
Powered equipments connected and power supply narmally
No powered equipments connected or no power supply
Network signal communicated
Network signal not communicated
Indicator Description
Normal
Power Unconnected
Always ON
Always ON
Always ON
Always OFF
Always OFF
Always ON
Power LED:P
PoE L ink
PoE Swi tchPoE Swi tch
123 4 9-UP 10 -UP
567 8
100M PoE port 100M Uplink port
Indicator Function switch
8FE Po E+2FE U P8FE Po E+2FE U P
Optional wall +machine hanger parts
1*Switch 1*Power Cable 1*User Manual+Warranty Card
PoE Link
PoE SwitchPoE Switch
123 4 9-UP 10-UP
567 8
8FE PoE+2FE UP8FE PoE+2FE UP
Warr anty Ca rd
Automatically detecting and supplying power for powered devices conformed to IEEE 802.3af/at
PoE++/HiPoE, unmanaged PoE switch(Ai-version) has new functions of HiPoE and PoEdog that
can efficiently solve the power-supply problems of high-power devices like high-power dome
cameras and wireless access point AP and achieve auto restore when the machine breaks down.
Similarly, it can solve the problems that restart the machine annually on the spot and installation
requirements on multiple switches.
◆
◆
◆
◆
◆
◆
◆
◆
PoE dog: real-time detection of powered devices status; when the device is abnormal, the switch
automatically restarts the port and restores PoE power supply to realize no duty.
HiPoE: first port can output HiPoE_60W.
IEEE802.3af/at PoE++/HiPoE, support all ports standard detection.
Support power supply for PoE devices such as AP and network monitoring cameras connected by
Cat5/6 ethernet cables.
Port
.
PoE Standard:
Port supports Auto MDI/MDIX.
supports lightning protection(secondary level requirements).
Single port supports PoE power:30W
Zero-configuration:automatically supply for adaptive devices.
Panel indicator monitors operating status and helps fault analysis.
◆
www.sigmasec.gr

G
NL
Figure1.2.1 three-pin power socket(Single-phase)
Fig 1.1.2 Power connection schematic diagram
Check up the power cable securely wrapped and connected to the AC power adapter connection or not.
Ensure the adequate space for heat dissipation and ventilation around the switch.
Do not stack heavy objects on the switch.
Connection of the Power Cable
1. Check up that the power supply is consistent with the marked requirements on the switch or not ;
2. The built-in power adapter is not needed, and it can be directly connected to AC100~240V and
50~60Hz;see Fig.1.2.2.
Specification of power socket
The inspection after installation
3
Installation and attentions
Desktop
When installing the switch on the desktop, the device must be placed flat on the table to keep it stable.
Please leave aside enough space between the device and other surrounding objects for good ventilation.
For the safe installation operation of switch, suggestions are as follows:
The switch adopts single-phase three-pin power socket, the middle one is the G wire,
the left one is the N wire, and the right one is the L wire. Please check before operation.
Please check up the following items after installation:
1. Enough space around the switch for heat dissipation and smooth ventilation or not.
2. The s
3. The power supply, switch, frame and other equipments are properly grounded;
upplying power of the power socket conformed to the specification of the switch.
PoE Link
PoE Sw itchPoE Sw itch
123 4 9-UP 10 -UP
567 8
8FE PoE +2FE UP8FE PoE +2FE UP
www.sigmasec.gr
www.sigmasec.gr

4
Application
Option 1
PoE Li nk
123 4 9-U P 10-U P 567 8
Power s upply a nd data tran smiss ion
for 8 dev ices sy nchronou sly
NVR
PoE Camera PoE Camera PoE Camera
Internet
PoE BT
Dome Camera
Option 2
PoE Li nk
123 4 9-U P 10-U P
567 8
NVR
PoE separator PoE separator PoE separator PoE separator
Internet
Non-PoE Camera Non-PoE Camera Non-PoE Camera
Power s upply a nd data tran smiss ion
for 8 dev ices sy nchronou sly
PoE Swi tch
8FE Po E+2FE U P
Non-PoE BT
Dome Camera
Option 3
PoE Lin k
123 4 9-UP 1 0-UP
567 8
8 port Gigabit Switch
DC IN
PC
PoE Camera PoE Camera
PoE AP
PoE Camera PoE AP
PoE S witch
8FE PoE +2FE UP
PoE outdoor AP
www.sigmasec.gr
www.sigmasec.gr
www.sigmasec.gr

Total Power/Input Voltage
5
Parameter
Network Protocol
Operating Temperature/
Humidity
Storage Temperature/
Humidity
210mm*150mm*35mm
270mm 220mm*68mm*
0.8kg/1.2kg
1.44Mpps
8*10/100Base-TX PoE port（Data/Power）
2*10/100Base-TX uplink RJ45 port (Data)
1-8 port support PoE(first port support output HiPoE_60W)
Function
Single port power
Power Pin
8 port Fast Ethernet Ai PoE Switch
N:(Standard Normal)+V:(Port Isolation)+ S(Ultral-far Mode)
10/100BaseT（X）Auto
2Gbps
1K
768K
10BASE-T : Cat3,4,5 UTP(≤250 meter)
100BASE-TX : Cat5 or later UTP(150 meter)
Default1/2(+), 3/6(-); Optional 4/5(+), 7/8(-)
Average15.4W;MAX 30W(Ai version:MAX 60W)
MAX 120W （AC100-240V 50/60Hz）
P:Power LED(Over-power LED)
Uplnik:(Green=10M LED+Orange=100M LED)
Port:(Green=Link LED+Orange=PoE LED)
V:(Port Isolation LED）
S:(Ultral-far Mode LED)
Built-in powerAC：100～240V 50-60Hz 1A
-10～+55°C; 5%～90% RH Non coagulation
-40～+75°C; 5%～95% RH Non coagulation
Desktop(optional wall+machine hanger parts)
3KV 8/20us;
Ip30
CE mark, commercial; CE/LVD EN60950;
FCC Part 15 Class B; RoHS;
Model
Product
Port
Port Specification
Transmission Mode
Bandwidth
Packet Forwarding
MAC Address
Buffer
Transmission
Distance
Watt
LED Indicator
Power
Product size
/Packing size
(L*W*H)
N.W/G.W(kg)
Installation
Lightning protection
level
Certificate
Warranty
Store and Forward(full wirespeed)
Standby Power Consumption≤3W
Whole device for 1 year (Accessories not included)
IEEE802.3af/at(AI version:first port supports HiPoE_60W)
PoE Standard
IEEE802.3
IEEE802.3u100BASE-TX
IEEE802.3x
IEEE802.3af/at//PoE++
IEEE802.3i 10BASE-T
hasivo HiPoE
NPS-08
www.sigmasec.gr

Attentions
■
■
■
■
■
■
■
Keep the status of power-off during installation, and wear anti-static wrist to ensure good contact
between anti-static wrist and skin to avoid the hidden danger.
The switch can only work normally under the correct power supply. Please confirm that the power
supply voltage is consistent with the voltage marked on the switch.
Before switch on, please make sure that it will not cause overload of the power circuit, so as not to
affect the normal operation of the switch or even unnecessary damage.
In order to avoid the danger of electric shock, do not open the shell up when the switch works,
even in the case of no live current, do not open.
Before cleaning the switch, pull out the power plug. Do not wipe it by using wet fabrics or liquid.
Install device in the rack-mount regularly from top to bottom, incase of over-load installation.
Don’t stack other heavy objects on the surface of the switch to avoid accidents.
To avoid equipment damage and personal injury caused by improper use, please follow the
precautions as below:
www.sigmasec.gr