SIIG AV-GM06Z3-S1 User manual

8x8 3Gbps HD/SDI Router
P/N: AV-GM06Z3-S1

~ 1 ~
Safety and Notice
The AV-GM06Z3-S1 3Gbps HD/SDI Router has been tested for conformance to safety
regulations and requirements, and has been certified for international use. However, like all
electronic equipments, the AV-GM06Z3-S1 should be used with care. Please read and follow the
safety instructions to protect yourself from possible injury and to minimize the risk of damage to
the unit.
Follow all instructions and warnings marked on this unit.
Do not attempt to service this unit yourself, except where explained in this manual.
Provide proper ventilation and air circulation and do not use near water.
Keep objects that might damage the device and assure that the placement of this unit is on a
stable surface.
Use only the power adapter and power cords and connection cables designed for this unit.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the
device before cleaning.

~ 2 ~
The AV-GM06Z3-S1 8x8 3Gbps HD/SDI Router provides the most flexible and cost effective
solution in the market to route 3Gbps high definition video sources from any of the eight SDI
sources to the any eight SDI receivers at the same time. This solution is well suited for use in
home theater, conference room presentation systems, or other similar setting or application.
Introduction
BNC cable
8x SDI Output
SDI Source 1
SDI Source 2
SDI Source 3
SDI Source 4
8x SDI Source
BNC cable
BNC cable
AV-GM06Z3-S
1

~ 3 ~
Features
SInputs meet SMPTE 259M, 292M, 424M,425M
Synchronizes input/output (switch after vertical sync)
Allows any SDI display to view any SDI source at any time
Auto-Reclocking
The router master can switch every output channels to any SDI inputs by push-in button, IR
remote controller or RS-232 control
Easy installation with rack-mounting and wall-mounting designs for master and receiver
respectively

~ 4 ~
Specifications & Package Contents
Model Name
AV-GM06Z3-S1
Technical
AV-GM06Z3-S1
Role of usage
True 8x8 Router
Video bandwidth
2.97 & 2.97/1.001Gbps
Video support
[3G] 1080p@50/59.94/60 (4:2:2)
[HD] 720p50/59.94/60, 1080p24/30, 1035i50/59.94/60, 1080i50/59.94/60
[SD] NTSC@59.94Hz, PAL@50Hz
Audio support
Yes
Cable equalization
[3G] up to 100m(300ft)/[HD-SDI] up to 150m (500ft) / [SD-SDI] up
to 300m (1000ft)
Reclocking function
Yes
PCB stack-up
4-layer board [impedance control —differential 100; single 50]
Input
8x SDI BNC
1x Synchronized BNC
1x RS-232
Output
8x SDI BNC
1x Synchronized BNC loop-out
SDI Input selection
Push button / IR remote / RS-232
IR remote control
Electro-optical characteristics: = 25/ Carrier frequency: 38kHz
RS-232 connector
DE-9 [9-pin D-sub female]
Mechanical
AV-GM06Z3-S1
Housing
Metal case
Dimensions
(L x W x H)
Model
440 x 310 x 43mm [1’5” x 1’ x 1.7”]
Package
528 x 398x 130mm [1’9” x 1’4” x 5.1”]
Carton
548x 422 x 282mm [1’10” x 1’5” x 11.1”]
Weight
Model
4051g [8.9 lbs]
Package
4900g [10.8 lbs]
Fixedness
1U rack-mount with ears and wall hanging holes
Power supply
AC Power 100-240V
Power consumption
358888 Watts [max]
Operation temperature
0~40C [32~104F]
Storage temperature
-20~60C [-4~140F]
Relative humidity
20~90% RH [no condensation]
Package Contents
1x AV-GM06Z3-S1
2x Rack-mounting ears
1x IR remote
1.
USB or RS-232 control must be connected either one at a time. Connecting both types of cables may
cause command confusion.

~ 5 ~

~ 6 ~
Front Panel
1. Power: Power control
2. Seven Segment LED Indicators: Control display
3. Front panel push buttons: Used to input source and display channel number
4. IR: IR receiver
Rear Panel
5. AC Power: 100-240V
6. RS-232: RS-232 control port
7. SW1: firmware update
8. Digital I/O: Control Singal
9. Sync In: External sync input
10. Sync Output External sync loop out
Panel Descriptions
1
2
3
4
6
5
7
10
11
12
8
9

~ 7 ~
11. INPUT 1 –8: SDI inputs
12. OUPUT PORT 1–8: SDI outputs

~ 8 ~
Main Firmware Update
Note
6
Factory default for SW Main is pin#1- OFF[] , pin#2- OFF[] . PLEASE MAINTAIN THIS SETTING AT
ANYTIME FOR REGULAR USE VIA RS-232 CONTROL!
8
Sequence for firmware update
WARNING! [Firmware update only can be done via RS-232 port and connection to PC set at
COM1)
1. Power off the AV-GM06Z3-S1. Execute the firmware update program on your PC via
COM1 port connection to the RS-232 port of the AV-GM06Z3-S1.
2. Set the pin#1 and pin#2 of [SW Main] at ON[] for firmware update mode.
4. Power on the AV-GM06Z3-S1. The firmware update program should begin this
update sequence automatically. If not, please check the RS-232 connection status
between PC and MA-5188.
5. After the OK message shows up to indicate the firmware update sequence for
designated Block is complete, please turn off the AV-GM06Z3-S1.
7. Set the [SW Main] switch position to Normal Operation Mode.
8. Power on the AV-GM06Z3-S1.
DIP Switch
Position
Description
Pin#1
Pin#2
OFF []
OFF []
Normal Operation
ON []
ON []
For Firmware Update
DIP Switch

~ 9 ~
AV-GM06Z3-S1
1. Connect all sources to SDI Inputs on the 8x8 SDI Router
2. Connect all outputs to SDI Receiver
3. Connect the AC power supply to the 8x8 SDI Router
4. Power on the 8x8 SDI Router AV-GM06Z3-S1
Hardware Installation