Silencer 7921P User manual

OWNER’S
MANUAL
Model: 7921P
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference; and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s authority to operate the equipment.
7921PUM 6/3/05 15:00 Page 1

2
Congratulations on your purchase of a quality Silencer security system. Your new Silencer security system
has been designed to provide years of trouble free service when operated and maintained in the manner set
forth in this manual. Your full knowledge of the features provided by your security system and their methods
of operation are essential for day-to-day usage. Please take a moment to read through this manual and
become familiar with the features that pertain to your security system. Located at the back of this booklet, we
have provided a listing of all the upgrade features available for your security system. Additional installed
features vary by dealership, but any can be added at a later date. Contact your new car dealership for details.
The Model Number of your Silencer Security System is 7921P
The basic function of this system is to provide an upgraded level of security to an existing manufacture
installed keyless entry system or security device. The 7921P can also be used as a stand alone Silencer
remote keyless entry and security system or a “remoteless” passive arm security system. Please read
and follow the procedures enclosed to operate your system.
Determine the Control Device
Your Silencer 7921P can be controlled from a variety of different devices. Determine which device is
controlling your system and proceed to that section of this manual. In some cases, the 7921P will have 3
different controllers. Read the information pertains to all controllers.
System Control by the Factory Keyless Entry Transmitter (Basic Operation)
If the vehicle you purchased came with remote keyless entry transmitters, two of the buttons on the
transmitter will be used to lock and unlock your vehicle. These buttons will have the words “LOCK” and
“UNLOCK” printed or engraved on them or they will have pictures of a padlock in a locked and unlocked
position (see illustration at above). Use the lock and unlock buttons on the transmitter to control your new
Silencer security system in the following manner.
Manual Arming and Disarming
1. Exit the vehicle and close all of the entrances.
Note: After closing the last protected entrance, you will hear the siren or horn chirp. The reason for this
chirp is covered below in the “Automatic Arming” section of the manual. Proceed as follows:
2. Press the LOCK button on your keyless entry transmitter. Your Silencer Security system will respond in
the following manner:
A. The siren or vehicle horn will emit a single chirp*.
B. The parking lights may flash one time.
C. The LED indicator for the security system will start to flash.
The system is now armed.
3. Press the UNLOCK button on your keyless entry transmitter. Your Silencer security system will respond
in the following manner:
A. The siren or vehicle horn will emit 2 chirps*.
B. The parking lights may flash two times.
C. The LED indicator for the security system will start flashing fast indicating that the system will rearm in
60 seconds. (Opening the driver’s door or turning on the ignition key will momentarily stop the auto
arming feature.)
The system is now disarmed.
Controlled by Factory
Supplied Keyless Transmitter
Controlled by
Silencer Remote Transmitter
Example of
Factory
Transmitter
Controlled by
Silencer Code Key
7921PUM 6/3/05 15:00 Page 2

*Some factory keyless entry systems have chirp confirmation as a built in feature. If this is true for your
vehicle, when the doors are locked or unlocked with the factory keyless transmitter, you may get more than
1 or 2 chirps as indicated above. If this condition becomes undesirable, the chirp indication from the
7921P can be turned off allowing only the factory system chirp. Contact your dealer for more details.
Automatic Arming with Manual Disarming
Note: When you take delivery of your new vehicle and Silencer 7921P security system, the automatic
arming feature is active to protect your vehicle even if you forget to arm your security system. If the
feature becomes undesirable, it can be programmed off leaving manual arming your only method to
secure your vehicle. Contact your dealer for further information.
1. Exit the vehicle and close all protected entrances. Once the last protected entrance is closed, your
Silencer security system will respond in the following manner.
A. The siren or vehicle horn will chirp one time.
B. The LED indicator will begin to flash fast to indicate that the 30 second auto arm timer is counting
down.
2. After 30 seconds has passed**, your Silencer security system will respond as follows.
A. The siren or vehicle horn will chirp once again indicating that the security system is fully armed.
B. The parking lights may flash one time.
C. The LED indicator will resume a normal flash speed indicating an armed condition.
D. The doors will become locked.
Note: Auto arm door lock control is an optional feature described in the back of this manual.
** The dome lights in some vehicles have a delay before they turn completely off. If your vehicle has
this type of delay, the 30 second auto arm timer will start when the dome light is completely off.
Depending on the length of time it takes the dome light to turn off, auto arming may take 45 to 60
seconds or more.
What to do if the Alarm is Sounding
Press the UNLOCK button on your keyless entry transmitter.
A. The siren or vehicle horn will stop sounding.
B. The parking lights may stop flashing.
C. The LED indicator will begin a special tamper mode flash sequence to let you know that your alarm
had been triggered.
Notations on Basic Operating Procedures
1. When you disarm the system while it is sounding, there are no disarm chirps.
2. After the security system has been triggered, the LED remains flashing even thought the security system
has been disarmed. This is a tamper indicator. Turning on the ignition key will reset this indicator.
3
System Control by the Factory Supplied Keyless Entry Transmitter (Basic Operation) (cont.)
System Control by the Silencer Remote Transmitter (Basic Operation)
If you purchased the 7921P Silencer security system and your vehicle did not come with a factory keyless system,
your dealer would have supplied you with 2 Silencer remotes. Use the lock and unlock buttons on the transmitter
to control your security system in the following manner:
Manual Arming and Disarming
1. Exit the vehicle and close all of the entrances.
Note: After closing the last protected entrance, you will hear the siren or horn chirp. The reason for
this chirp is covered in the “Automatic Arming” section of the manual. Proceed as follows:
7921PUM 6/3/05 15:00 Page 3

4
2. Press the LOCK button on your Silencer transmitter. Your Silencer security system will respond in the
following manner:
A. The siren or vehicle horn will emit a single chirp.
B. The parking lights may flash one time.
C. The LED indicator for the security system will start to flash.
The system is now armed.
3. Press the UNLOCK button on your Silencer remote transmitter. Your Silencer security system will
respond in the following manner:
A. The siren or vehicle horn will emit 2 chirps.
B. The parking lights may flash two times.
C. The LED indicator for the security system will start flashing fast indicating that the system will
rearm in 60 seconds. (Opening the drivers door or turning on the ignition key will momentarily stop
the auto arming feature.)
The system is now disarmed.
Automatic Arming with Manual Disarming
Note: When you take delivery of your new vehicle with a Silencer 7921P security system, the automatic
arming feature is active to protect your vehicle even if you forget to arm your security system. If the
feature becomes undesirable, it can be programmed off leaving manual arming your only method to
secure your vehicle. Contact your dealer for further information.
1. Exit the vehicle and close all protected entrances. Once the last protected entrance is closed, your
Silencer security system will respond in the following manner:
A. The siren or vehicle horn will chirp one time.
B. The LED indicator will begin to flash fast to indicate that the 30 second auto arm timer is counting
down.
2. After 30 seconds has passed**, your Silencer security system will respond as follows:
A. The siren or vehicle horn will chirp once again indicating that the security system is fully armed.
B. The parking lights may flash one time.
C. The LED indicator will resume a normal flash speed indicating an armed condition.
Note 1: Once the ignition key switch is turned off, the automatic arming timer will start counting
after the last protected entrance is closed. Reopening any protected entrance within the 30 second
time will stop the counter and reset it. Closing the entrance will start the counter once again but you
will not get a beep when closing the door for the second time.
Note 2: Auto arm door lock control is an optional feature described in the back of this manual.
** The dome lights in some vehicles have a delay before they turn completely off. If your vehicle has
this type of delay, the 30 second auto arm timer will start when the dome light is completely off.
Depending on the length of time it takes the dome light to turn off, auto arming may take 45 to 60
seconds or more.
What to do if the Alarm is Sounding
Press the UNLOCK button on your Silencer transmitter.
1. The siren or vehicle horn will stop sounding.
2. If the parking lights are flashing they will stop flashing.
3. The LED indicator will begin a special tamper mode flash sequence to let you know that your alarm had been
triggered.
Notations on Basic Operating Procedures:
1. When you disarm the system while it is sounding, there are no disarm chirps.
2. After the security system has been triggered, the LED remains flashing even thought the security system has
been disarmed. This is a tamper indicator. Turning on the ignition key will reset this indicator.
System Control by the Silencer Remote Transmitter (Basic Operation) (continued)
7921PUM 6/3/05 15:00 Page 4

5
If you purchased the 7921P Silencer security system and your vehicle did not come with a factory keyless
system and you chose not to purchase the remote transmitter control option, your dealer would have
supplied you with 2 Silencer Code Keys. Silencer code keys can be attached to your existing key ring and
are used for disarming your security system. Your Silencer 7921P security system operates in the
following manner when using the Code Keys.
1. Exit the vehicle and close all of the entrances. After the last protected entrance is closed, the security
system will respond as follows:
A. The siren or vehicle horn will emit a single chirp.
B. The LED indicator for the security system will start to flash fast to indicate that the 30 second
timer* is counting down to arm the vehicle.
2. After the 30 seconds has passed*, the security system will respond in the following manner:
A. The siren or vehicle horn will emit another single chirp
B. The parking lights may flash once.
C. The LED indicator will return to a normal armed flashing mode.
The system is now armed.
3. Enter the vehicle through the drivers door and insert the Silencer Code Key into the LED receptacle:
A. The siren or vehicle horn will emit 2 chirps.
B. The parking lights may flash two times.
C. The LED indicator for the security system will stop flashing.
D. Remove the Code Key and start the vehicle.
The system is now disarmed.
* The dome lights in some vehicles have a delay before they turn completely off. If your vehicle has this
type of delay, the 30 second auto arm timer will start when the dome light is completely off. Depending
on the length of time it takes the dome light to turn off, auto arming may take 45 to 60 seconds or more.
What to do if the Alarm is Sounding
Enter the vehicle and insert the Code Key into the LED receptacle.
1. The siren or vehicle horn will stop sounding.
2. If the parking lights are flashing they will stop flashing.
3. The LED indicator will begin a special tamper mode flash sequence to let you know that your alarm
had been triggered.
Notations on Basic Operating Procedures
1. When you disarm the system while it is sounding, there are no disarm chirps.
2. After the security system has been triggered, the LED remains flashing even though the security system
has been disarmed. This is a tamper indicator. Turning on the ignition key will reset this indicator.
System Control by the Silencer Code Key (Basic Operation)
7921P Primary Feature Operation
Other than arming and disarming your security system, the 7921P has a host of non-option features that
enhance ownership and the level of security provided by the 7921P system. Please take moment to become
familiar with the operation of these features as you may need to use them at some point in time. To practice
operating these features, repeat the enclosed procedure for each feature as it is written or illustrated.
Take a moment to become familiar with the operation of the primary features provided by your new security
system as you may need to use them at some point in time. To test the primary features, repeat the
following procedures exactly as they are listed:
System Override/Valet
A patented removable switch is used to override the security system in the event that the transmitters are
lost or fail to operate and to put the security system in non-operational mode (valet) for vehicle servicing etc.
7921PUM 6/3/05 15:00 Page 5

Override Operation (security system is armed)
1. Enter the vehicle, the security systems will begin sounding at this point, and place the override
switch into the switch housing. Make sure that the switch button is in the OUT position.
2. Place the ignition key into the ignition switch and turn the ignition switch to the ON position.
3. Within 5 seconds of turning the ignition key ON, press the valet switch button IN until it locks.
4. The horn/siren will stop sounding.
5. The LED indicator will be solid red.
The security system is overridden and is now in the Valet Mode.
Valet Operation (security system is already disarmed)
1. Place the valet switch into the switch holder making sure that the switch button is in the OFF
position (switch button is out).
2. Turn the ignition key to the ON position.
3. Within 5 seconds of turning the ignition key ON, push IN the valet switch.
4. The LED will be on solid indicating that the security system is in the Valet Mode.
Note 1: If the valet switch is already in the ON position when you turn ON the ignition key, the valet
function will be bypassed. Turn OFF the ignition key, set the switch to the OFF position and try again.
Note 2: If you fail to push IN the valet switch within 5 seconds of turning ON the ignition key, the valet
function will be locked out. Turn OFF the ignition key, set the switch to the OFF position and try again.
Starter Disable
Your Silencer security system has a built-in starter interrupt relay that will break the connection between
your ignition key and the starter on your vehicle. To test this feature, repeat the following procedure:
1. Enter the vehicle and close all the entrances.
2. Press the LOCK button on the transmitter.
3. Turn the ignition key to the start position. The engine will not crank over.
4. Turn the ignition key to the OFF position and press the UNLOCK button on the transmitter.
5. Turn the ignition key back to the START position and the engine will crank over and start.
Remote Panic
The 7921P provides a remote panic function which allows the user to trigger the alarm by remote in the
case of an emergency.
Factory Supplied Keyless Entry Transmitter
1. Ignition key must be OFF.
2. Press the LOCK button 4 times.
3. The siren will begin to sound and the parking lights may begin to flash.
4. Press the UNLOCK button. The siren will stop sounding and if the parking lights are flashing they
will stop flashing.
Note: If the panic function is not turned off by the transmitter, the siren will continue to sound for 60
seconds and then turn off by itself.
Silencer Transmitter
1. The ignition key must be OFF.
2. Press and hold the button for 3 seconds and your Silencer system will respond in the following manner:
A. The siren or vehicle horn will begin sounding.
B. The parking lights may begin flashing.
C. Press the button to turn off the panic feature.
Note: If the panic function is not turned off by the transmitter, the siren/horn will continue to sound for
60 seconds and then reset by itself.
6
Note: The removable valet switch can only be inserted into the
valet switch housing one way. Do not force the switch or bend the
switch terminals.
7921P Primary Feature Operation: (continued)
7921PUM 6/3/05 15:00 Page 6

7
Silent Arming or Disarming from the Factory Keyless Transmitter
From time to time, it may be necessary to arm or disarm your Silencer security system without hearing
the chirp indicator. To operate this function, repeat the following procedure:
Silent Arming (Security system is disarmed)
1. Press the UNLOCK button on the factory keyless remote transmitter.
2. Within 3 seconds, Press the LOCK button on the factory keyless remote transmitter.
3. The system will become armed silently.
Silent Disarming (Security system is armed)
1. Press the LOCK button on the factory keyless remote transmitter.
2. Within 3 seconds, Press the UNLOCK button on the factory keyless remote transmitter.
3. The system will become armed silently.
Silent Arming or Disarming from the Silencer Remote Transmitter
Silent Arming (Security system is disarmed)
1. Press the LOCK and UNLOCK buttons on the Silencer remote transmitter at the same time.
2. They system will become armed silently.
Silent Disarming (Security system is armed)
1. Press the LOCK and UNLOCK buttons on the Silencer remote transmitter at the same time.
2. The system will become disarmed silently.
Optional Features
C hirp Delete
The 7921P control module can be programmed by the dealer so there will be no arm/disarm status
chirps. The four chirp tamper disarm warning indicator will always be on for you safety.
Pathway Illumination
If the pathway illumination function has been programmed on by your dealer, your vehicle’s parking
lights will illuminate at the time the security system is disarmed by the remote transmitter. The parking
lights will remain on for 30 seconds after the security system is disarmed. Turning on the ignition key will
turn off the parking lights before 30 seconds.
Ignition Key Controlled Door Locking/Unlocking
If the ignition key lock/unlock function has been programmed on by your dealer the doors will automatically
become locked 3 seconds after the ignition key is set to the on position or unlocked after ignition key is
turned off.
1. Enter the vehicle and close all protected entrances.
2. Turn the ignition key to the ON position.
3. Within 3 seconds the door locks will become locked.
4. Turn OFF the ignition key. The door locks will become unlocked.
Notations About Ignition Controlled Locking
A. If a protected door is open, the ignition door locking function is disabled.
B. If the door locks are manually locked, the alarm system will still unlock them when the ignition key
is turned off.
7921P Primary Feature Operation: (continued)
7921PUM 6/3/05 15:00 Page 7

Automatic Arm Door Locking
If the “Auto Arm Locking” feature has been programmed on by your dealer, your doors will become locked
after the last protected entrance is closed and the system becomes armed. To test this feature, follow the
testing instructions for “Last Door Automatic Arming” above and the doors will become locked when the
system arms.
Note: leaving a door open or leaving the ignition key in the ON position will stop the auto arm/locking
timers.
WARNING!
• Do not leave your keys inside the vehicle at gas stations.
• Always use your valet switch to put your system in valet mode when you go to the car wash.
• If your vehicle has more than one driver, make sure everyone is familiar with the auto arm/locking
system to prevent the vehicle keys from being locked inside the vehicle.
Shock/Impact Detectors
Your Silencer 7921P is set up to accept “Single-Zone” and “Dual-Zone” type shock/impact sensors.
These type of devices will detect impacts to your vehicle that are related to forced entry. “Single-Zone”
shock/impact sensors will detect hard impacts to your vehicle such as breaking a window or using a
hammer on the door key lock cylinder. If any of these level of impacts are detected the siren or vehicle
horn will start to sound.
Optional Features (continued)
© 2005 Copyright Magnadyne Corp. 7921PUM 6-3-05 Rev. B
3 Year Warranty
Your new Silencer®Security Systems is warranted to be free of defects for 3 years. Silencer®or its authorized
agents will within 3 years from the date of sale to you, repair or replace said product or any part thereof, at the option
of the Silencer®or its authorized agents, if said product or part is found defective in materials or workmanship,
when properly connected and operating on the correct power requirements designated for the specific product. This
warranty and Silencer®or its authorized agents obligations hereunder do not apply where the product was; damaged
while in the possession of the consumer, subjected to unreasonable or unintended use, not reasonably maintained,
or serviced by anyone other than Silencer®or its authorized agents, or where the warning seal on the product is
broken or the power and/or plugs are detached from the unit. This warranty does not cover the cabinet appearance
items or accessories used in connection with this product, or any damage to the products resulting from improper
installation, alteration, accident, misuse, abuse or acts of nature. Silencer®OR ITS AUTHORIZED AGENTS SHALL
NOT BE LIABLE TO ANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR CLAIMS EXCEPT THOSE
ACCORDED BY LAW. NO EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN EXCEPT THOSE SET FORTH
HEREIN. NO IMPLIED WARRANTY SHALL EXTEND BEYOND 3 YEARS FROM THE DATE OF SALE. Some states do
not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitations or exclusion may not apply to you. This warranty
gives you specific legal rights, and you may have other rights that vary from state to state. Defective merchandise
should be returned to the original point of purchase or secondly, to 1111 W. Victoria Street, Compton CA 90220.
Return Authorization must be obtained before sending, or merchandise may be refused. All claims concerning your
Silencer®Security System should be referred to your selling dealer. If you are away from the vicinity of the selling
dealer please call [phone].
7921PUM 6/3/05 15:00 Page 8