Silicon Graphics Rackable C2112-4RP9 User manual

SGI®Rackable™ C2112-4RP9 System
User Guide
007-5926-002

COPYRIGHT
© 2013 Silicon Graphics International Corp. All rights reserved; provided portions may be copyright in third parties, as indicated elsewhere herein. No
permission is granted to copy, distribute, or create derivative works from the contents of this electronic documentation in any manner, in whole or in part,
without the prior written permission of SGI.
LIMITED RIGHTS LEGEND
The software described in this document is “commercial computer software” provided with restricted rights (except as to includedopen/free source) as specified
in the FAR 52.227-19 and/or the DFAR 227.7202, or successive sections. Use beyond license provisions is a violation of worldwide intellectual property laws,
treaties and conventions. This document is provided with limited rights as defined in 52.227-14.
The electronic (software) version of this document was developed at private expense; if acquired under an agreement with the USA government or any
contractor thereto, it is acquired as “commercial computer software” subject to the provisions of its applicable license agreement, as specified in (a) 48 CFR
12.212 of the FAR; or, if acquired for Department of Defense units, (b) 48 CFR 227-7202 of the DoD FAR Supplement; or sections succeeding thereto.
Contractor/manufacturer is SGI, 46600 Landing Parkway, Fremont, CA 94538.
TRADEMARKS AND ATTRIBUTIONS
Silicon Graphics, SGI, and the SGI logo, Rackable, and Supportfolio are trademarks or registered trademarks of Silicon Graphics International Corp. in the
United States and/or other countries worldwide.
InfiniBand is a registered trademark of the InfiniBand Trade Association. Intel, Itanium, and Xeon are trademarks or registered trademarks of Intel Corporation
or its subsidiaries in the United States and other countries. ConnectX and Mellonox are registered trademarks of Mellonox Technologies, Ltd. Internet Explorer
and MS-DOS are registered trademarks of Microsoft Corporation. Java and Java Virtual Machine are trademarks or registered trademarks of Sun Microsystems,
Inc. Linux is a registered trademark of Linus Torvalds, used with permission by SGI. Matrox is a registered trademark of Matrox Electronic Systems Ltd. Novell
and Novell Netware are registered trademarks of Novell Inc. PCIe and PCI-X are registered trademarks of PCI SIG. Red Hat and all Red Hat-based trademarks
are trademarks or registered trademarks of Red Hat, Inc. in the United States and other countries. SUSE LINUX and the SUSE logo are registered trademarks
of Novell, Inc. UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company, Ltd.
All other trademarks mentioned herein are the property of their respective owners.
Adaptec, Host, and the Adaptec logo are registered trademarks of Adaptec Inc.

007-5926-002 iii
Record of Revision
Version Description
001 May 2013
Original printing.
002 September 2013
Added support for Intel®Xeon®E5-2600v2 Series processors plus miscellaneous
front matter changes.

007-5926-002 v
Contents
Record of Revision . . . . . . . . . . . . . . . . . . . . . . . iii
About This Guide . . . . . . . . . . . . . . . . . . . . . . . xiii
Audience. . . . . . . . . . . . . . . . . . . . . . . . . . xiii
Chapter Descriptions . . . . . . . . . . . . . . . . . . . . . . xiv
Related Publications. . . . . . . . . . . . . . . . . . . . . . . xv
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . xv
Product Support . . . . . . . . . . . . . . . . . . . . . . . . xvi
Reader Comments . . . . . . . . . . . . . . . . . . . . . . . xvi
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . 1
Server Chassis Features . . . . . . . . . . . . . . . . . . . . . . 2
Serverboard Features . . . . . . . . . . . . . . . . . . . . . . 4
Additional Hardware Components . . . . . . . . . . . . . . . . . . . 7
Advanced Power Management . . . . . . . . . . . . . . . . . . . . 8
Special System Notes . . . . . . . . . . . . . . . . . . . . . . 8
Independent Nodes . . . . . . . . . . . . . . . . . . . . . . 8
System Power . . . . . . . . . . . . . . . . . . . . . . . 9
SATA Backplane/Drives . . . . . . . . . . . . . . . . . . . . 9
2 System Safety . . . . . . . . . . . . . . . . . . . . . . . . 11
Electrical Safety Precautions . . . . . . . . . . . . . . . . . . . . 11
General Safety Precautions . . . . . . . . . . . . . . . . . . . . . 13
ESD Precautions. . . . . . . . . . . . . . . . . . . . . . . . 13
Operating Precautions . . . . . . . . . . . . . . . . . . . . . . 14
3 Server Installation . . . . . . . . . . . . . . . . . . . . . . . 15
Unpack the System . . . . . . . . . . . . . . . . . . . . . . . 15
Prepare for Setup . . . . . . . . . . . . . . . . . . . . . . 15
Choose a Setup Location . . . . . . . . . . . . . . . . . . . . 16

vi 007-5926-002
Contents
Warnings and Precautions . . . . . . . . . . . . . . . . . . . . . 16
Rack Precautions . . . . . . . . . . . . . . . . . . . . . . 16
Server Precautions . . . . . . . . . . . . . . . . . . . . . . 17
Rack Mounting Considerations . . . . . . . . . . . . . . . . . . . . 17
Ambient Operating Temperature . . . . . . . . . . . . . . . . . . 17
Reduced Airflow . . . . . . . . . . . . . . . . . . . . . . 17
Mechanical Loading. . . . . . . . . . . . . . . . . . . . . . 17
Circuit Overloading . . . . . . . . . . . . . . . . . . . . . . 18
Reliable Ground . . . . . . . . . . . . . . . . . . . . . . . 18
Install the System into a Rack . . . . . . . . . . . . . . . . . . . . 18
Separate the Sections of the Rack Rails and Install Outer Rack Rails . . . . . . . . . 18
Install the Inner Rail Extensions. . . . . . . . . . . . . . . . . . . 20
Install the Server in a Rack . . . . . . . . . . . . . . . . . . . . 21
Check the Serverboard Setup. . . . . . . . . . . . . . . . . . . . . 22
Removing the Chassis Cover and Protective Film . . . . . . . . . . . . . . 22
Checking the Components and Setup . . . . . . . . . . . . . . . . . 23
Checking the Drive Bay Setup . . . . . . . . . . . . . . . . . . . 24
Checking the Airflow . . . . . . . . . . . . . . . . . . . . . 24
Providing Power. . . . . . . . . . . . . . . . . . . . . . . 24
4 System Interface. . . . . . . . . . . . . . . . . . . . . . . . 25
Control Panel Components . . . . . . . . . . . . . . . . . . . . . 26
Drive Carrier LEDs . . . . . . . . . . . . . . . . . . . . . . . 28
Power Supply LED . . . . . . . . . . . . . . . . . . . . . . . 29
5 Chassis Maintenance . . . . . . . . . . . . . . . . . . . . . . 31
Before You Start . . . . . . . . . . . . . . . . . . . . . . . . 32
Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . 32
Left-Right and User Position . . . . . . . . . . . . . . . . . . . 32
Removing the Chassis Cover and Protective Film . . . . . . . . . . . . . . . 33
Replacing a Power Supply . . . . . . . . . . . . . . . . . . . . . 34
Installing and Removing Disk Drives . . . . . . . . . . . . . . . . . . 36
Removing a Hard Drive Carrier from the Chassis . . . . . . . . . . . . . . 37
Removing a Drive Tray from a Drive Carrier . . . . . . . . . . . . . . . 38

Contents
007-5926-002 vii
Installing a Hard Drive into a Carrier . . . . . . . . . . . . . . . . . 39
Replacing System Fans . . . . . . . . . . . . . . . . . . . . . . 40
6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 43
If the System Does Not Power Up . . . . . . . . . . . . . . . . . . . 44
System Powers Up But Will Not Boot . . . . . . . . . . . . . . . . . . 44
No Video After System Power Up . . . . . . . . . . . . . . . . . . . 45
Memory Errors . . . . . . . . . . . . . . . . . . . . . . . . 45
A Technical Specifications . . . . . . . . . . . . . . . . . . . . . 47
B BIOS Error Codes . . . . . . . . . . . . . . . . . . . . . . . 51

007-5926-002 ix
Figures
Figure 1-1 The SGI Rackable C2112-4RP9 Server . . . . . . . . . . 1
Figure 1-2 Front Chassis View . . . . . . . . . . . . . . . 3
Figure 1-3 Rear Chassis View . . . . . . . . . . . . . . . 3
Figure 1-4 Serverboard Block Diagram . . . . . . . . . . . . . 6
Figure 2-1 Installing the Onboard Battery . . . . . . . . . . . . 12
Figure 3-1 Separating and Installing the Rack Rails. . . . . . . . . . 19
Figure 3-2 Installing the Inner Rail Extensions . . . . . . . . . . . 20
Figure 3-3 Installing the Server in a Rack . . . . . . . . . . . . 21
Figure 3-4 Accessing the Inside of the Chassis . . . . . . . . . . . 23
Figure 4-1 Front Control Panels . . . . . . . . . . . . . . . 25
Figure 4-2 Control Panel Components . . . . . . . . . . . . . 26
Figure 5-1 Removing the Chassis Cover. . . . . . . . . . . . . 33
Figure 5-2 Power Supply Release Tab . . . . . . . . . . . . . 34
Figure 5-3 Removing the Power Supply. . . . . . . . . . . . . 35
Figure 5-4 Motherboard Drawer Locations. . . . . . . . . . . . . 36
Figure 5-5 Drive Carrier Release Tab . . . . . . . . . . . . . 37
Figure 5-6 Removing Drive Carrier From Chassis . . . . . . . . . . 38
Figure 5-7 Mounting a Disk into a Drive Carrier . . . . . . . . . . 39
Figure 5-8 Removing Fan Housing from Chassis . . . . . . . . . . 40
Figure 5-9 Removing Fan from Fan Housing . . . . . . . . . . . 41

Tables
007-5926-002 xi
Tables
Table 1-1 Server Chassis Features . . . . . . . . . . . . . . 2
Table 1-2 Serverboard Features. . . . . . . . . . . . . . . 4
Table 4-1 Control Panel Components . . . . . . . . . . . . . 27
Table 4-2 Disk Carrier LEDs . . . . . . . . . . . . . . . 28
Table 4-3 Power Supply LED States . . . . . . . . . . . . . 29
Table 5-1 Hard Drives and Corresponding Motherboards . . . . . . . . 36
Table A-1 Temperature, Humidity, and Altitude Specifications . . . . . . 47
Table A-2 Miscellaneous System Specifications . . . . . . . . . . 48
Table B-1 BIOS Error Codes . . . . . . . . . . . . . . . 51

007-5926-002 xiii
About This Guide
This guide provides an overview of the installation, architecture, general operation, and
descriptions of the major components in the SGI®Rackable™C2112-4RP9 server. It also provides
basic troubleshooting and maintenance information as well as important safety and regulatory
specifications.
Audience
This guide is written for owners, installers, system administrators, and users of SGI Rackable
C2112-4RP9 computer systems. It is written with the assumption that the reader has a good
working knowledge of computers and computer systems.

xiv 007-5926-002
About This Guide
Chapter Descriptions
The following topics are covered in this guide:
• Chapter 1, “Introduction”
Provides an overview of SGI Rackable C2112-4RP9 server components.
• Chapter 2, “System Safety”
Provides system safety information.
• Chapter 3, “Server Installation”
Provides a quick setup checklist to get the SGI Rackable C2112-4RP9 operational.
• Chapter 4, “System Interface”
Describes how you monitor the overall status of the system as well as the activity and health
of specific components.
• Chapter 5, “Chassis Maintenance”
Describes how you replace fans, disk drives, and power supplies.
• Chapter 6, “Troubleshooting”
Describes some basic steps to troubleshoot your system.
• Appendix A, “Technical Specifications,”
Describes system component specifications.
•Appendix B, “BIOS Error Codes,”
Provides BIOS error code information.

About This Guide
007-5926-002 xv
Related Publications
The following SGI documents are relevant to the SGI Rackable C2112-4RP9 server:
• SGI Foundation Software release notes
• SGI Performance Suite release notes
• SGI InfiniteStorage series documentation
• Man pages
You can obtain SGI documentation, release notes, or man pages in the following ways:
• Refer to the SGI Technical Publications Library at http://docs.sgi.com. Various formats are
available. This library contains the most recent books and man pages.
• Refer to the SGI Supportfolio™ webpage for release notes and other documents whose
access require a support contract. See “Product Support” on page xvi.
Conventions
The following conventions are used throughout this document:
Convention Meaning
Command This fixed-space font denotes literal items such as commands, files,
routines, path names, signals, messages, and programming language
structures.
variable The italic typeface denotes variable entries and words or concepts being
defined. Italic typeface is also used for book titles.
user input This bold fixed-space font denotes literal items that the user enters in
interactive sessions. Output is shown in nonbold, fixed-space font.
[ ] Brackets enclose optional portions of a command or directive line.
... Ellipses indicate that a preceding element can be repeated.
man page(x) Man page section identifiers appear in parentheses after man page names.
GUI element This font denotes the names of graphical user interface (GUI) elements such
as windows, screens, dialog boxes, menus, toolbars, icons, buttons, boxes,
fields, and lists.

xvi 007-5926-002
About This Guide
Product Support
SGI provides a comprehensive product support and maintenance program for its products. SGI
also offers services to implement and integrate Linux applications in your environment.
• Refer to http://www.sgi.com/support/
• If you are in North America, contact the Technical Assistance Center at
[phone]SGI or contact your authorized service provider.
• If you are outside North America, contact the SGI subsidiary or authorized distributor in
your country.
Reader Comments
If you have comments about the technical accuracy, content, or organization of this document,
contact SGI. Be sure to include the title and document number of the manual with your comments.
(Online, the document number is located in the front matter of the manual. In printed manuals, the
document number is located at the bottom of each page.)
You can contact SGI in any of the following ways:
• Send e-mail to the following address: t[email protected]
• Contact your customer service representative and ask that an incident be filed in the SGI
incident tracking system.
http://www.sgi.com/support/supportcenters.html
SGI values your comments and will respond to them promptly.

007-5926-002 1
Chapter 1
1. Introduction
The SGI Rackable C2112-4RP9 server is a 2U rackmount server (see Figure 1-1).It hastwo main
subsystems: the 2U server chassis and four nodes with dual-processor serverboards.
Figure 1-1 The SGI Rackable C2112-4RP9 Server
This chapter describes the server using the following topics:
•“Server Chassis Features” on page 2
•“Serverboard Features” on page 4
•“Additional Hardware Components” on page 7
•“Advanced Power Management” on page 8
•“Special System Notes” on page 8

2007-5926-002
1: Introduction
Server Chassis Features
Table 1-1 describes the main features of the SGI Rackable C2112-4RP9 server chassis.
Table 1-1 Server Chassis Features
Feature Description
System power The chassis includes a high-efficiency 80-plus Platinum certified power
supply, rated at 1620 Watts plus one redundant backup power supply. In the
unlikely event your power supply fails, replacement is simple and can be
accomplished without tools.
SATA subsystem The chassis supports up to 12 hot-swappable 3.5” SATA drives in trays (3
for each node). These drives are hot-swappable units and are connected to a
backplane that provides power and control.
Note: The operating system you use must have RAID support to enable the
hot-swap capability of the drives.
Front control panel The chassis includes four front control panels on the handles of the chassis.
Each control panel provides you withsystem monitoring and control for one
server node. LEDs indicate system power, HDD activity, network activity,
system overheat, and power supply failure. A main power button is also
included on each control panel.
I/O ports The chassis is a proprietary-form-factor chassis designed to be used in a 2U
rackmount configuration. The chassis provides a low-profile add-on card
slot, a COM port, a VGA port, two USB 2.0 ports, one IPMI Ethernet port,
and two gigabit Ethernet ports per node.
Cooling system The chassis has four system fans powered from either the backplane or the
serverboards. If not powered from the backplane, the chassis powers the four
fans from the four motherboards so that when one of the motherboard
drawers is removed, the other motherboards will continue running all fans.
Air shrouds The chassis includes four plastic air shrouds that direct the airflow where
cooling is needed on each serverboard. Always use the air shroud included
with your chassis on each serverboard.
Mounting rails The chassis includes a set of quick-release rails and can be placed in a rack
for secure storage and use. To set up your rack, follow the step-by-step
instructions included in this manual.

Server Chassis Features
007-5926-002 3
Figure 1-2 shows the noteworthy components on the front of the server chassis.
Figure 1-2 Front Chassis View
Figure 1-3 shows the noteworthy components on the rear of the server chassis.
Figure 1-3 Rear Chassis View

4007-5926-002
1: Introduction
Serverboard Features
At the heart of the SGI Rackable C2112-4RP9 server are dual-processor serverboards based on
the Intel®C602 chipset and designed to provide maximum performance. Four of these
serverboards can be mounted in the server chassis. Table 1-2 describes the major features of the
serverboards.
Table 1-2 Serverboard Features
Feature Description
Processors Eachserverboardsupports singleor dual Intel Xeon®E5-2600orE5-2600v2
Series processors.
Memory Each serverboard has eight (8) DIMM slots supporting up to 256 GB of
DDR3-1600/1333/1066/800 MHz speed registered ECC SDRAM in up to
512 MB, 1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB sizes at 1.35V or 1.5V
voltages.
SATA subsystem A SATA controller is integrated into the C602 chipset to provide up to a
three-port 6 Gb/s SATA subsystem—two SATA 3 (6 Gb/s) and two SATA
2 (3 Gb/s). The SATA subsystem supports either RAID 0 and 1 (SATA 2) or
RAID 0, 1, and 5 (SATA 3). The SATA drives are hot-swappable units.
Note: The operating system you use must have RAID support to enable the
hot-swap capability and RAID function of the SATA drives.
PCI expansion
slots For each node, the server has one PCIe®3.0 x16 slot (Slot 1) available for
use with a riser card.
Onboard
controllers/ports A serverboard can include the following: – One fast UART 16550 serial port
– One 9-pin RS-232 port
– One Mellonox®Connect-X3 InfiniBand®supporting a single QSFP
connector One COM port
– One VGA (monitor) port
– Two USB 2.0 ports (Additional internal USB headers are included on the
serverboard.)
– One IPMI-dedicated LAN port
– Two Ethernet ports
Graphics
Controller Each serverboard features an integrated Matrox®G200eW video controller.