Kontron CG2300 User manual

www.kontron.com
» Kontron Configuration Guide «
CG2300 Carrier Grade Server
Document Revision 1.01

www.kontron.com
2
Revision History
Revision
Brief description of changes
Date of issue
1.00
First release
02/02/2015
1.01
Correction to some contact information
09/02/2015
Customer Service
Contact Information:
Kontron America, Inc.
Kontron Europe GmbH
14118 Stowe Drive
Poway, CA 92064-7147
USA
Tel.: [phone]
Fax:[phone]
E-mail: [email protected]
Lise-Meitner-Str. 3-5
86156 Augsburg
Germany
Tel.: +800-KONTRONAG
Tel.: [phone]
E-mail: [email protected]
Visit our site at: www.kontron.com
Copyright © 2015 Kontron America Inc.
All rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the express written permission from
Kontron.
Customer Comments
If you have any difficulties using this user's guide, discover an error, or just want to provide some feedback, please send a message to Kontron. Detail any
errors you find. We will correct the errors or problems as soon as possible and post the revised user's guide on our website. Thank you.

www.kontron.com
3
Acronyms
AC
Alternating Current
CPU
Central Processing Unit
CRMS
Communications Rack Mount Servers
DC
Direct Current
DDR4
Double Data Rate Fourth Generation
DIMM
Dual In-Line Memory Module
EIA
Electronic Industries Alliance
ESD
Electrostatic discharge
ETSI
European Telecommunications Standards Institute
eUSB
Embedded Universal Serial Bus
FH/FL
Full Height/Full Length
Gbe
Gigabit Ethernet
GHz
Gigahertz
HDD
Hard Disk Drive
HW
Hardware
KVM
Kernel-based Virtual Machine
LP
Low Profile
NEBS
Network Equipment-Building System
NIC
network interface controller
OSS
Operations System and Support
PCI
Peripheral Component Interconnect
PCI-E Gen 3
Peripheral Component Interconnect Express, Third Generation
PSU
Power Supply Unit
RAID
Redundant Array of Independent Disks
RDIMM
Registered Dual In-Line Memory Module
RMM
Remote Management Module
RoHS
Restriction of Hazardous Substances
SAS
Serial Attached SCSI (Small Computer System Interface)
SATA
Serial Advanced Technology Attachment
SD
Secure Digidal
SKU
Stock keeping unit
SSD
Solid State Drive
SW
Software
THOL
Tested Hardware and Operating System List
TOC
Table of Content
UDIMM
Unregistered Dual In-Line Memory Module

www.kontron.com
4
Contents
1. Introduction..............................................................................................................................................................................................................6
1.1 Product Description .................................................................................................................................................................................. 6
1.2 Purpose of this Document ......................................................................................................................................................................... 6
1.3 General Flow for Configuring a CG2300 System......................................................................................................................................... 7
2. Ordering CG2300 Systems........................................................................................................................................................................................8
A. CG2300 Base System ........................................................................................................................................ 8
B. Select the Quantity and Type of Power Supply .......................................................................................................10
C. Select Quantity and Type of CPUs .......................................................................................................................12
D. Heat Sink ......................................................................................................................................................13
E. Select PCIe Risers ...........................................................................................................................................13
F. Select RAID ...................................................................................................................................................15
G. Select Storage................................................................................................................................................16
H. Select Memory ...............................................................................................................................................16
I. Select Remote Management Module Option..........................................................................................................16
J. Select System Mounting...................................................................................................................................17
3. Ordering CG2300 Serviceable Items .......................................................................................................................................................................19
List of Figures
Figure 1: PCIe Riser Options................................................................................................................................................................................................13
Figure 2: TMLCMOUNT21....................................................................................................................................................................................................23
Figure 3: Slide-in Rail-Type System .....................................................................................................................................................................................24
List of Tables
Table 1: Configuration Flow...................................................................................................................................................................................................7
Table 2: CG2300 Base System SKU ......................................................................................................................................................................................8
Table 3: CG2300 Base System Components .........................................................................................................................................................................9
Table 4: Power Supply Options............................................................................................................................................................................................10
Table 5: Intel® Xeon® Processors Supported by the CG2300 .............................................................................................................................................12
Table 6: PCIe Riser Options.................................................................................................................................................................................................14
Table 7: CG2300 Raid Options............................................................................................................................................................................................15
Table 8: Battery Backup Bracket Option for Intel RS3DC080 Card........................................................................................................................................15
Table 9: Remote Management Module Option.....................................................................................................................................................................16
Table 10: Rack Mount Kits Options (refer to Appendix A for additional details) .....................................................................................................................17
Table 11: Serviceable Items Options ...................................................................................................................................................................................19
Table 12: 2-post Rack Mounting Kit Options........................................................................................................................................................................21
Table 13: 4-post Rack Mounting Kit Options........................................................................................................................................................................21
Table 14: TMLPMOUNT4x/5x Feature Comparison ..............................................................................................................................................................22

www.kontron.com
5
Electrostatic Discharge
CAUTION! The CG2300 is sensitive to electrostatic discharge (ESD). Users must observe the appropriate precautions when handling ESD-sensitive devices.
Limited Warranty
Kontron grants the original purchaser of Kontron's products a THREE YEAR LIMITED HARDWARE WARRANTY as described in the following. However, no other
warranties that may be granted or implied by anyone on behalf of Kontron are valid unless the consumer has the express written consent of Kontron.
Kontron warrants their own products, excluding software, to be free from manufacturing and material defects for a period of 36 consecutive months from the
date of purchase. This warranty is not transferable nor extendible to cover any other users or long- term storage of the product. It does not cover products
which have been modified, altered or repaired by any other party than Kontron or their authorized agents. Furthermore, any product which has been, or is
suspected of being damaged as a result of negligence, improper use, incorrect handling, servicing or maintenance, or which has been damaged as a result of
excessive current/voltage or temperature, or which has had its serial number(s), any other markings or parts thereof altered, defaced or removed will also be
excluded from this warranty.
If the customer's eligibility for warranty has not been voided, in the event of any claim, he may return the product at the earliest possible convenience to the
original place of purchase, together with a copy of the original document of purchase, a full description of the application the product is used on and a
description of the defect. Pack the product in such a way as to ensure safe transportation (see our safety instructions).
Kontron provides for repair or replacement of any part, assembly or sub-assembly at their own discretion, or to refund the original cost of purchase, if
appropriate. In the event of repair, refunding or replacement of any part, the ownership of the removed or replaced parts reverts to Kontron, and the remaining
part of the original guarantee, or any new guarantee to cover the repaired or replaced items, will be transferred to cover the new or repaired items. Any
extensions to the original guarantee are considered gestures of goodwill, and will be defined in the "Repair Report" issued by Kontron with the repaired or
replaced item.
Kontron will not accept liability for any further claims resulting directly or indirectly from any warranty claim, other than the above specified repair,
replacement or refunding. In particular, all claims for damage to any system or process in which the product was employed, or any loss incurred as a result of
the product not functioning at any given time, are excluded. The extent of Kontron liability to the customer shall not exceed the original purchase price of the
item for which the claim exists.
Kontron issues no warranty or representation, either explicit or implicit, with respect to its products reliability, fitness, quality, marketability or ability to fulfill
any particular application or purpose. As a result, the products are sold "as is," and the responsibility to ensure their suitability for any given task remains that
of the purchaser. In no event will Kontron be liable for direct, indirect or consequential damages resulting from the use of our hardware or software products,
or documentation, even if Kontron were advised of the possibility of such claims prior to the purchase of the product or during any period since the date of its
purchase.
Please remember that no Kontron employee, dealer or agent is authorized to make any modification or addition to the above specified terms, either verbally or
in any other form, written or electronically transmitted, without the company's consent.

www.kontron.com
6
1. Introduction
1.1 Product Description
The CG2300 Carrier Grade Server is the 7th generation of Kontron’s 2U Carrier Grade Server products. The CG2300 supports the Intel® Xeon® E5-2600 v3
series processors, coupling high performance with power efficiency to provide improved performance-per-watt over previous-generation rack-mount servers.
The CG2300 is designed to meet NEBS-3 and ETSI certification which is suited for a host of applications in the telecom Central Office and industrial
environment. The server is targeted to OSS (Operations System and Support), Billing, Provisioning, Softswitch, Media Server, Wireless and Unified Messaging,
Call Center and many other applications. It can also support manufacturing, industrial, oil & gas, utility and even military applications where a rugged, highly
reliable server is required for harsh environments such as dust, high altitude, fire hazard, earthquake propensity, and high ambient temperatures.
To add to the many recognized benefits of Kontron’s Carrier Grade Server family, the CG2300 introduces several new important features such as support of
Intel Haswell processors, DDR4 memory, PCI-E Gen3, hot-swap/redundant fans and many flash storage formats (SD, eUSB, M.2).
More detailed product information on the CG2300 is available on Kontron’s website at:
http://www.kontron.com/products/systems-and-platforms/communication-rackmount-servers/carrier-grade-servers/cg2300-carrier-grade-server.html
1.2 Purpose of this Document
This document serves as an ordering reference guide, providing details on what parts are available from Kontron for the CG2300 Carrier Grade Server and its
associated accessories and spares. Included are the necessary order codes and other important configuration information related to the ordering of the
product.
Supported third-party components are not covered by this document, and may be found in the Tested Hardware and Operating System List (THOL) of the
CG2300.

www.kontron.com
7
1.3 General Flow for Configuring a CG2300 System
Table 1: Configuration Flow
Step
Implication
NOTE or Reference info
A. Start with Base System
NOTE: No PSU included
B. Select quantity of power supply and
input type (AC or DC)
Redundant (2) or non-redundant (1)
Type: AC or DC
NOTE: If non-redundant, add a PSU
filler.
C. Select quantity and type of CPUs
CPU quantity determines:
number of PCI-e slots available
number of DIMM slots
available
CPU type impacts performance
See Technical Product Specification
D. Heatsink
NOTE: Two CPU heatsinks shipped with
Base System.
E. Select left and right PCI Risers
Determines number of slots &PCIe
bus width (One x16 or two x8)
F. Select RAID
Software or Hardware RAID
SW RAID: 0/1/10 included
HW RAID: refer to THOL or section F
below.
No additional cable kit required.
G. Select Storage
SAS, SATA, M.2, SD Card or eUSB
See THOL
H. Select Memory
Sized for the application
Refer to Tested Memory List for list of
validated DIMMs
Refer to Installation & Maintenance
Guide for installation instructions
I. Select Remote Management
Basic or Advanced features
(Advanced = KVM and media
redirection)
NOTE: Dedicated server management
NIC port is built-in (motherboard).
Basic = built-in
Advanced = Activation key required
J. Select System Mounting
Rack mount kits
Refer to Appendix A

www.kontron.com
8
2. Ordering CG2300 Systems
This section includes important information regarding how to order CG2300 systems. Please be familiar with each of these areas before placing an order.
A. CG2300 Base System
Table 2: CG2300 Base System SKU
Product Code
Description
Min. Order
Qty.
CG2300-xxx
CG2300 Carrier Grade Server
Base System
(PSU not included)
1
The CG2300 system SKU is ordered using the Product Code as the order number. The above SKU is “Base System” SKU—meaning it does not include PSUs,
processors, memory, hard drives, power cord, operating system, or plug-in adapters. Those components should be ordered separately as Accessories from
Kontron or from third party vendors listed in the Tested Hardware and Operating System List (THOL).

www.kontron.com
9
See the CG2300 Base System table below for a list of components included. Notice that there are a number of optional accessory items which must be
ordered separately.
Table 3: CG2300 Base System Components
Component Description
AC Configuration
DC Configuration
Chassis (sheet metal, top cover, PCI cages, air duct, interconnection cables,
misc. parts)
1 included
Baseboard S2600CW2SK, power distribution board, system boards, fans,
interconnect cables
Included
AC power supply (850W)
None included with base
system, To be ordered:
1 or 2 per system
-
DC power supply (850 W)
-
None included with Base
System, To be ordered:
1 or 2 per system
Power Cable (AC)
Purchase separately1
Not included
Power Distribution Board
1 included
Power Supply Filler Panel
None included with Base System
Order 1 if you order only one PSU
Bezel
1 included
RDIMM/UDIMM memory slots (memory not included)
16 slots available
Bays for hot-swap 2.5” Hard Disk Drives and drive carriers
6 included
Rear Panel GbE NIC ports (via motherboard)
2 ports available
SAS SW RAID 5 Key
Purchase separately from Intel
Hardware RAID cable kit
Included, use same cables (built-in)
HW RAID Adapter, optional battery backup
Purchase separately4
HW RAID battery mounting bracket
Optional Accessory2
SW RAID 0/1/10
Included
Basic Remote Management Features
Included
Advance Remote Management Features (RMM4Lite)
Optional Accessory2
Right side Dual slot PCIe x8 passive riser
Optional Accessory2
Right side Single slot PCIe x16 passive riser
Optional Accessory2
Left side Single slot PCIe X16 passive riser
Optional Accessory2
Left side Dual slot PCIe x8 passive riser
Optional Accessory2
Rack Mount Kits
Optional Accessory3
SD Flash Module
1 Included
Kontron Deployment Assistant on SD Flash media
1 Included
Rail Enabling Kit
Optional Accessory3
Processor
Purchase separately, refer to Table 5
Heatsink
2 Included
RDIMM/UDIMM DDR4 Memory
Purchase separately4
Hard Disk Drives (SAS or SATA SSD)
Purchase separately4
eUSB Flash Drive
Purchase separately4
M.2 Flash Drive
Purchase separately4
1Refer to AC power cord accessory in this section
2Refer to step E and I in this section
3Refer to “Rack Mounting Options” in Appendix A
4Should be purchased separately (refer to THOL and TML)

www.kontron.com
10
B. Select the Quantity and Type of Power Supply
The CG2300 System accommodates up to two power supply units. Order one (non-redundant) or two (redundant) PSUs. If a single PSU is used per system, you
must order a PSU Filler panel (to respect forced airflow principle).
You must order either AC or DC, no AC-DC mix is possible.
Order same quantity of AC power cords to agree with the quantity of AC power supplies in the final system.
Because DC power input cabling is usually custom, no DC power cord is offered. Each DC PSU contains a DC input terminal block for terminating DC input
power.
Table 4: Power Supply Options
Product Code
Description
Products
Supported
Included in Base Model
(Y/N)
Min. Order Qty
1056-8389
AC Power Supply
CG2300
N
1 (for AC
system)
1056-8385
DC Power Supply
Includes input power connector
CG2300
N
1 (for DC
system)

www.kontron.com
11
K00837-001
PSU Filler Panel
CG2300,
CG2200
N
0 (1 if non-
redundant
system)
1-340000-0
AC Power Cord*
Should be ordered by North America
customers. International customers
should procure their specific power
cords directly.
All CRMS servers
N
1 (AC system
only)
* Power cords are not included with the system. For AC Power cords, order the above North American power cable using the provided product code. This power
cable is RoHS-compliant.

www.kontron.com
12
C. Select Quantity and Type of CPUs
The CG2300 is designed to support the following processor SKUs from the Intel®Xeon®processor E5-2600 series. The CG2300 Base System includes no
CPUs. Customer must separately purchase CPU 1 and 2.
Table 5: Intel® Xeon® Processors Supported by the CG2300
Processor Number
Cores
Speed
TDP
Memory Speed Support
Kontron P/N
Intel P/N (tray)
Embedded Family (5-7 years availability/support)
E5-2608L v3
6
2.0 GHz
52 W
DDR4-1866MHz
1056-9896
CM8064402033500
E5-2618L v3
8
2.3 GHz
75 W
DDR4-1866MHz
1056-9889
CM8064401610301
E5-2628L v3
10
2.0 GHz
75 W
DDR4-1866MHz
1056-8325
CM8064401547200
E5-2648L v3
12
1.8 GHz
75 W
DDR4-2133MHz
1056-9887
CM8064401546007
E5-2658 v3
12
2.2 GHz
105 W
DDR4-2133MHz
1056-8322
CM8064401545904
E5-2680 v3
12
2.5 GHz
120 W
DDR4-2133MHz
1056-9917
CM8064401439612
Server Family
E5-2623 v3
4
3.0 GHz
105 W
DDR4-1866MHz
1056-9909
CM8064401832000
E5-2670 v3
12
2.3 GHz
120 W
DDR4-2133MHz
1056-9905
CM8064401544801
E5-2683 v3
14
2.0 GHz
120 W
DDR4-2133MHz
1056-9900
CM8064401609728
E5-2690 v3
12
2.6 GHz
135 W
DDR4-2133MHz
1056-9907
CM8064401439416
E5-2695 v3
14
2.3 GHz
120 W
DDR4-2133MHz
1056-9902
CM8064401438110
E5-2698 v3
16
2.3 GHz
135 W
DDR4-2133MHz
1056-9904
CM8064401609800
Notes:
The above processors in the Embedded family are on Intel’s long life roadmap and are recommended with the CG2300 for highest performance
and long availability and support.
More specifically, the E5-2628L v3, E5-2648L v3 and E5-2658 v3 where successfully tested against NEBS Operating Temperature.
The above processors in the Server family are appropriate for applications that are not specifically requiring the stringent NEBS (Operating
Temperature) requirements compliancy or long life support.
These processors are orderable from Kontron or Intel using the indicated part numbers.
Use of the above processors requires passive heatsink. Two heatsinks are included in the Base System, no need to order separately.

www.kontron.com
13
D. Heat Sink
The CG2300 Base System is delivered with two CPU heatsinks.
This heatsink design was done by Kontron for specific use in the CG2300 system. In order to obtain best CPU and DIMM thermal performance, Kontron does
not recommend using any other heatsink model.
If a heatsink requires replacement, please use product code found in the Serviceable Items section below.
E. Select PCIe Risers
This diagram shows the PCI riser physical arrangement. The CG2300 Base System comes with no risers, but can support the addition of 2 risers, a right-side
and a left-side riser.
Figure 1: PCIe Riser Options
Please note that in the diagram above, the three Low Profile PCIe slots are available only when both CPU 1 and CPU 2 are populated.
PCIe risers are NOT included in the Base system.

www.kontron.com
14
Additional Full-height full-length PCIe slots are made available with the purchase of risers. The following risers are available:
Table 6: PCIe Riser Options
Product Order Code
Description
Min. Order Qty
Choose one
for Right
side
CG2200-RISER2SX8R
Right side Dual slot PCI-e x8 Gen 3 passive riser
1
CG2200-RISER1SX16R
Right side Single slot PCI-e x16 Gen 3 passive riser
1
Choose one
for Left
Side
CG2200-RISER1SX16L
Left side Single slot PCI-e X16 Gen3 passive riser
1
CG2200-RISER2SX8L
Left side Dual slot PCI-e x8 Gen 3 passive riser
1
None of the above risers are included in the Base System.

www.kontron.com
15
F. Select RAID
The CG2300 Base System supports software RAID 0/1/10 for 6 SAS hard drives or SATA SSD’s. If additional level of SW or HW RAID is required, please refer
to the options detailed in Table 7.
Table 7: CG2300 Raid Options
RAID Type
Supported
RAID
Included in CG2300 Base
System?
Additional item to order
Software
0/1/10
Yes
None
Software
0/1/5/10/50
No
Intel AXXRPFKHY5
Hardware
0/1/5/10/50
No
LSI MegaRAID SAS9341-8i
Hardware
1/5/6/10/50/60
No
Intel RS3DC080*
Upon selection of a hardware RAID card, no supplemental cables are required. Built-in cables simply need to get disconnected from the on-board SAS
controller and connected to HW RAID card.
*The Intel RS3DC080 RAID card comes optionally with a battery backup unit (Intel AXXRMFBU4), which requires the following bracket for proper mounting in
the system:
Table 8: Battery Backup Bracket Option for Intel RS3DC080 Card
Product Code
Description
Products
Supported
Included in Base
System (Y/N)
Min.
Order Qty
K00740-001
Mounting bracket for Intel Battery Backup
unit (AXXRMFBU4)
CG2300,
CG2200
N
1

www.kontron.com
16
G. Select Storage
SAS HDD / SATA SSD
The CG2300 Base System supports for up to 6 SAS hard drives or SATA SSD’s. SATA rotating hard drives are not recommended for use in this system.
Please refer to the Tested Hardware and Operating System List (THOL) for complete listing of HDD’s that have been validated for the CG2300. The THOL is a
customer-driven document. If a specific HDD is required please contact Kontron’s customer support.
Flash Drives
Two front accessible SD memory slots are available. The CG2300 can be configure to boot from SD memory modules for software update or logging purposes.
Generic SD-Flash devices may be sourced from a wide variety of vendors.
An internal optional eUSB Flash Drive is supported. Refer to THOL (Tested Hardware and O/S List) for ordering choices.
An internal optional M.2 Flash Drive is supported. Refer to THOL (Tested Hardware and O/S List) for ordering choices.
H. Select Memory
Refer to THOL (Tested Hardware and O/S List) for ordering choices.
I. Select Remote Management Module Option
The Basic Remote Management feature of the motherboard comes in by default. In order to enable Advanced features (KVM and media redirection), the
following Activation key must be purchased and installed on the motherboard. This is an optional accessory.
NOTE: The motherboard includes a dedicated 1GbE RJ45 Management Port, available in the rear portion of the system. Basic features are available through
the same dedicated and built-in management port, without use of RMM4 or RMM4LITE, meaning that the management port is active with or without the
RMM4LITE key installed. If you are already familiar with CG2200, please note that RMM4 is not usable on CG2300.
Table 9: Remote Management Module Option
Product Code
Description
Products
Supported
Included in Base
System (Y/N)
Min.
Order Qty
AXXRMM4LITE
Intel® Remote Management Module 4
LITE Activation key
CG2300,
CG2200
N
1

www.kontron.com
17
J. Select System Mounting
There are many choices for mounting of the CG2300 within rack enclosures. Depending on the application, the following rack mount kits are available. Rack
mounting kits for 2-post or 4-post, 19-inch or 23-inch racks are offered for this product. These include TMLCMOUNT21, TMLPMOUNT41, TMLPMOUNT51,
TMLPMOUNT52, and TMLPSLIDE01.
Please refer to Appendix A to determine the correct options to suit your needs.
The TMLPSLIDE01 is an accessory kit designed for use in conjunction with slide rails to produce a rack mounted serviceable server. The TMLPSLIDE01 kit
contains two Universal Front Mounting Brackets that secure the server to the front of the rack. The sliding rails and optional mounting brackets required to
mount the server must be purchased through the channel.
Table 10: Rack Mount Kits Options (refer to Appendix A for additional details)
Product Code
Description
Included in Base
Model (Y/N)
Min. Order
Qty
TMLCMOUNT21
Rack Mount Kit TMLCMOUNT21
Used for mounting servers on a 19-inch wide, 2-post
rack
N
10
TMLPMOUNT41
Rack Mount Kit TMLPMOUNT41
Used for mounting servers on 19-inch wide, 2-post or 4-
post racks
N
10
TMLPMOUNT51
Rack Mount Kit TMLPMOUNT51
Used for mounting servers on 19-inch wide, 2-post or 4-
post racks
N
1
TMLPMOUNT52
Rack Mount Kit TMLPMOUNT52
Used for mounting servers on 23-inch wide, 2-post or 4-
post racks
N
1

www.kontron.com
18
TMLPSLIDE01
Universal Front Mounting Brackets
The Accuride 22-inch Model 305A-LR slide rails would
use TMLPSLIDE01.
Each kit contains two Universal Front Mounting Brackets
that secure the server to the front of the rack.
N
1
Note: Using slide rails could result in non-compliance with Seismic Zone 4 requirements of NEBS-3 certification.

www.kontron.com
19
3. Ordering CG2300 Serviceable Items
The table below lists all of the Serviceable Spares items that may be ordered for the CG2300 system. Generally these are items that could potentially fail or
need replacement over the life of the product. These items are made available so that customers might stock their service depots and repair centers. Please
read the following notes regarding this parts list.
3rd Party Accessories: For a listing of compatible 3rd party accessories, please refer to the Tested Hardware and Operating System List (THOL)
document.
Table 11: Serviceable Items Options
Product Code
Description
Products
Supported
Included in Base
Model (Y/N)
Min. Order
Qty
NSNSASHDDCARQ
SAS HDD/SATA SSD Carrier
Contents: Carrier, black plastic filler, screws (4)
CG2300,
CG2200
Y
(six included)
1
CG2100-BEZEL01
Bezel
CG2300,
CG2200
Y
(one bezel)
1
1056-5174
Heatsink
Contents: passive heatsink, pre-installed thermal
paste
CG2300
Y
(2 included)
1
S2600CW2SK
Intel Server Board S2600CW2SK
CG2300
Y
1

www.kontron.com
20
CG2200-FANSET
Fan Assembly (6 fans)
Contents: 6 x 80m assembly fans. Includes plastic
parts (finger guard).
CG2300,
CG2200
Y
1