Sim-Lab X1 User manual

INSTRUCTION MANUAL
X1
VERSION 1.0
Last updated: 14-09-2022

2|2 48
BEFORE YOU START:
Thank you for purchasing this Sim-Lab product! On the following pages, you will find detailed instructions
on assembly. This requires only a set of simple tools and some of your time. Please check the bill of
materials before starting (pages 45-47) and make sure all the parts are delivered.
Since this is our most feature rich cockpit so far, for some parts of assembly we urge you to get some
assistance Especially when turning over the base and fitting the uprights, an extra pair of hands really
does come in handy.
For current P1-X users who purchased an X1 upgrade kit, please skip to Page 13. Remove
the P1-X uprights and possibly the side mount, and you can follow along with this manual.
Breaking tabs:
Sometimes tabs from corner brackets need to be broken off in
order to fit as instructed. Place a flathead screwdriver behind
the tab and tilt upwards.
Always make sure to point away from you while doing so.
To know when to do this, we will show the following
symbol next to the brackets.
Inserting Slot-Nuts:
You got excited, finished the build, put the caps on, but forgot to install
one element. Do not worry. It happens to everyone. In this diagram, you
can see how to insert a Slot-Nut directly into the slot from the side.
You can also use one of your smaller Hex wrenches to help wiggle
the Slot-Nut in place.
Tools needed:
3/4/5/6MM - 8/10/24MM

3|3 48
BUILD 2X
Slot-Nut M8
A10/C6
4X/4X
1350MM
1X
AP1
C6
A10
C6

4|4 48
BUILD 2X
Slot-Nut M8
4X
500MM
1X
AP2
A10

5|5 48
500MM
or
20”
Only full tighten bolts until after
the pedal tray has been fitted.
M8 X 16
16X
Washer M8
16X
Corner
Bracket
8X
A8
A9
A4

6|6 48
Foot
Support Plate
Nut M16 Washer M16
Foot Foot
Support Plate
Nut M16 Washer M16
Foot
BUILD
BOTH
VERSIONS
2X
1X 2X2X1X 1X 2X2X1X
C4
C5
C2
C1

7|7 48
M8 X 25
8X
Corner Bracket
Cap
8X
Profile 120x40
End-Cap
4X
A5
A6
C3

8|8 48
BUILD 2X
Corner
Bracket*
2X
M8 X 16 Slot-Nut M8
2X
500MM
1X
Washer M8
2X
2X
AP3
A10
A4
A9
A8

9|9 48
Corner Bracket
Cap
4X
Profile 40X40
End-Cap
4X
M8 X 16
4X
Slot-Nut M8
4X
Washer M8
4X
A5
A8
A9
A7
A10

10 |10 48
Slot-Nut M8
8X
D10

11 |11 48
M8 X 25
8X
Pedal Plate
LEFT (D3)
1X
Pedal Plate
RIGHT (D4)
1X
470MM
1X
470MM
1X
D8
DP1
DP2
D3
D4

12 |12 48
M8 X 25
8X
Washer M8
8X
D5
D9

13 |13 48
Upright
Bracket LF
1X
Upright
Bracket RF
1X
Upright
Bracket LR
1X
Upright
Bracket RR
1X
M8 X 16
12X
Slot-Nut M8
12X
Washer M8
12X
B8
B34
B7
B9
B10
B30
B23

14 |14 48
The right upright (BP4) is
assembled similarly. For the
orientation, please see Page 15.
BUILD 2X
Upright
LEFT (BP3)
1X
Profile 120x40
End-Cap
2X
Slot-Nut M8
6X
B34
BP3
B19

15 |15 48
M8 X 16
12X
Washer M8
12X
B34
B23
BP4

16 |16 48
M8 X 20
8X
Slot-Nut M8
6X
848MM
1X
Sandwich
120 X 80
2X
B34
B26
BP1
B11

17 |17 48
M8 X 20
8X
Washer M8
8X
Slot-Nut M8
12X
B34
B30
B22

18 |18 48
M8 X 30
4X
Cap-Washer
M8
4X
Monitor Side
Plate
2X
834MM
1X
Washer M8
(DIN 988)
4X
B28
B13
BP6
B21
B28
B21

19 |19 48
4X
Cap-Washer
M8
4X
Washer M8
(DIN 988)
4X
M8 X 30
B32 B21
B28

20 |20 48
BUILD 2X
260MM
1X
Profile 120x40
End-Cap
1X
Slot-Nut M8
Sandwich
120x40
1X
M8 X 20
2X 2X
B34
B19
BP2
B26
B12