Sim-Lab P1-X User manual

P1-X sim racing chassis
INSTRUCTION MANUAL
Copyright© 2021 - Sim-Lab Products | Revision 1.2
https://sim-lab.eu/shop/product/p1-x-sim-racing-cockpit-black-533
inf[email protected]
SKU: SLC003 SLC004 SLC005 SLC006 SLC007 SLC008

BOX B (Hardware kit)
BOX C
(Pedal tray)
BOX D
(Feet)
BOX A (Profile kit)
5/6 mm 11 mm
Required tools:
Thank you for purchasing a Sim-Lab P1-X sim racing chassis! On
the following pages you will find a detailed instruction howe to build
this cockpit. Assembling requires a set of simple tools, and general
knowledge of how to use them and a bit of technical insight.
There are 12 Variant of the P1-X sim racing cockpit. Every variant is
covered in this manual. Take care to find the illustrations that are
applicable to the one you chose. Generally it takes about 3-4 hours
to build this cockpit. Before starting please check contents and
make sure all the parts are accounted for in the packages.
2

500
B7 B13 B24
Base assembly
3

B7 B13
B8 B14
Rubber feet
Adjustable feet
4
F5
B2
F1 F2 F3 F4
4x

*break off the lip on the connector bracket
B7 B13 B24B16
Adding wheel uprights
3
5
B25

B7 B17 B15
Pedal deck assembly
4
Side mount assembly
5
6
C11
C12
B12

*break off the lip on the connector bracket
Front mount assembly
6a
7
FR2
FR1
FR10
FR14
FR13
FR3
FR5

Wheeldeck assembly
6b
8
WH9 WH8 WH11
WH7
WH5 WH12
A ( 0,60 : 1 ) A

Fanatec Podium mount assembly
6c
9
DD8
DD8
DD7

Parts list - Main kit
10
BOX A
Base profiles
Part No. Part name QTY UoM Note
A1 Profile 40mm slot 8 (Black, 40x160L) - 1350mm 2 Units
A2 Profile 40mm slot 8 (Black, 40x160L) - 500mm 2 Units
A3 Profile 40mm slot 8 (Black, 40x120L) - 780mm 2 Units
BOX B
Hardware kit
Part No. Part name QTY UoM Note
B1 Cover cap for corner bracket (40x40) 20 Units
B2 Rubber feet 4 Units
B3 End cap profile (40x40L) 9 Units
B4 End cap profile (40x80L) 1 Units
B5 End cap profile (40x120L) 4 Units
B6 End cap profile (40x160L) 4 Units
B7 Slot 8 nut (M8) 65 Units
B8 Slot 8 nut (M6) 12 Units
B9 Slot 8 nut (M4) 4 Units
B10 Slot 8 nut (M5) 4 Units
B11 Washer (Black steel, M8, Plain black) 10 Units
B12 Sandwich plate small 40x40 1 Units
B13 Bolt - DIN 912 (Black steel, 16mm, M8) 50 Units
B14 Bolt - DIN 912 (Black steel, 20mm, M6) 8 Units
B15 Bolt - DIN 7991 (Black steel, 25mm, M8) 12 Units
B16 Bolt - DIN 7991 (Black steel, 20mm, M8) 20 Units
B17 Bolt - DIN 912 (Black steel, 25mm, M8) 8 Units
B18 Bolt - DIN 912 (Black steel, 20mm, M8) 10 Units
B19 Bolt - DIN 912 (Black steel, 12mm, M6) 4 Units
B20 Profile 40mm slot 8 (Black, 40x40L) - 500mm 2 Units
B21 Profile 40mm slot 8 (Black, 40x40L) - 320mm 1 Units
B22 Profile 40mm slot 8 (Black, 40x40L) - 200mm 2 Units
B23 Profile 40mm slot 8 (Black, 40x80L) - 580mm 1 Units
B24 Corner bracket (40x40) 20 Units
B25 Sandwich plate large 2 Units
BOX C
P1-X pedal tray
Part No. Part name QTY UoM Note
C1 Slot 8 nut (M5) 12 Units
C2 Slot 8 nut (M6) 12 Units
C3 Slot 8 nut (M8) 10 Units
C4 Washer (Black steel, M8, Plain black) 4 Units
C5 Bolt - DIN 912 (Black steel, 16mm, M6) 12 Units
C6 Bolt - DIN 7991 (Black steel, 25mm, M8) 10 Units
C7 Bolt - DIN 912 (Black steel, 25mm, M8) 10 Units
C8 Bolt - DIN 912 (Black steel, 16mm, M5) 12 Units
C9 Profile 40mm slot 8 (Black, 40x160L) 2x M8 Thread - 470mm 1 Units
C10 Profile 40mm slot 8 (Black, 40x80L) 2x M8 Thread - 470mm 1 Units
C11 P1-X pedal plate [Left] 1 Units
C12 P1-X pedal plate [Right] 1 Units

Parts list - Variants
11
Front mount
Part No. Part name QTY UoM Note
FR1 Front mount bracket [ALU 15mm] 1 Units
FR2 Front mount side plate [Left] 1 Units
FR3 Front mount side plate [Right] 1 Units
FR4 Bolt - DIN 912 (Black steel, 20mm, M6) 4 Units
FR5 Bolt - DIN 912 (Black steel, 20mm, M8) 6 Units
FR6 Bolt - DIN 912 (Black steel, 40mm, M8) 4 Units
FR7 Spacer - male / female (10mm, M6) 4 Units
FR8 Corner bracket (40x40) 4 Units
FR9 Cover cap for connector bracket (40x40) 4 Units
FR10 Nut (M8, DIN 985 locknut, Galvanised) 12 Units
FR11 Washer (Black steel, M8, Plain black) 4 Units
FR12 Slot 8 nut (M8) 4 Units
FR13 Bolt - DIN 7991 (Black steel, 30mm, M8) 4 Units
FR14 Bolt - DIN 7991 (Black steel, 25mm, M8) 4 Units
Wheeldeck plate
Part No. Part name QTY UoM Note
WH1 Wheeldeck to plate 1 Units
WH2 Wheeldeck side plate [LEFT] 1 Units
WH3 Wheeldeck side plate [RIGHT] 1 Units
WH4 Bolt - DIN 912 (Black steel, 16mm, M8) 4 Units
WH5 Bolt - DIN 912 (Black steel, 20mm, M8) 8 Units
WH6 Bolt - DIN 7991 (Black steel, 16mm, M8) 2 Units
WH7 Bolt - DIN 7991 (Black steel, 25mm, M8) 8 Units
WH8 Washer (Black steel, M8, Plain black) 18 Units
WH9 Corner bracket (40x40) 4 Units
WH10 Cover cap for connector bracket (40x40) 4 Units
WH11 Nut (M8, DIN 985 locknut, Galvanised) 10 Units
WH12 Slot 8 nut (M8) 10 Units
Fanatec Podium mounting bracket
Part No. Part name QTY UoM Note
DD1 Fanatec DD sidemount base holder [Left] 1 Units
DD2 Fanatec DD sidemount base holder [Right] 1 Units
DD3 Fanatec DD sidemount profile holder [Left] 1 Units
DD4 Fanatec DD sidemount profile holder [Right] 1 Units
DD5 Profile 40mm slot 8 (Black, 40x80L) - 194mm 2 Units
DD6 Slot 8 nut (M8) 8 Units
DD7 Bolt - DIN 7991 (Black steel, 20mm, M8) 8 Units
DD8 Bolt - DIN 912 (Black steel, 20mm, M8) 8 Units
DD9 Bolt - DIN 912 (Black steel, 20mm, M6) 4 Units
DD10 Washer (Black steel, M8, Plain black) 8 Units
BOX D
Sim Feet (Optional)
Part No. Part name QTY UoM Note
F1 Leveling feet Diameter 80mm - M16x125 4 Units
F2 Nut (M16, DIN 934 nut, Galvanised) 8 Units
F3 Washer (Galvanised, M16, Plain black) 8 Units
F4 Slot 8 nut (M8) 8 Units
F5 Bolt - DIN 912 (Black steel, 25mm, M8) 8 Units
F6 Feet support plate (alu 15mm) 4 Units