Simplicity Baker 1692615 User manual

B EHIND SNOWTI
7/22E
Mfg. No. 1692615
IROWER

Table of Contents
HANDLE & CONTROLS ............................................................. 2
ENGINE
.......................................................................... 4
FRAME
........................................................................... 6
AUGER DRIVE ..................................................................... 8
AUGER HOUSING
& CHUTE
........................................................ 10
WHEELS
& TRACTION DRIVE ....................................................... 12
TRANSMISSION . PEERLESS MODEL 700-027 ......................................... 14
DECAL &WRAPPER EXTENSION
................................................... 16
STANDARD HARDWARE TORQUE CHART ............................................ 18
PART NUMBER INDEX
............................................................ Al
Simplicity
Sno-Away Models
5-55 & 7-55
5 HP Models
Mfg.No. 1691411
Serial No. 6137 & Up
7 HP Models
Mfg.No. 1691413
Serial No. 13781 & Up
Mfg.No. 1691414
Serial No. 2000 & Up
1

Handle & Controls
Apply adhesive
NOTE: Unless noted otherwise,
use the standard hardware
torque specification chart.
43 -3
2

All Models
Handle
& Controls
REF.
NO. PART NO. QTY. DESCRIPTION
1 121175 1
2176934 1
3916168 2
41916964
1
5 1923341 2
61960093
1
71668188 2
81668189
1
91674177 1
10 1674178 1
11 1674329 1
12 1674580 2
13 1676252
1
14 1676253 1
15 1676325 1
16 1676390 1
17 1676444 2
18 1676450 2
19 1676451 2
20 1676452 2
21 1676484
1
22 1676485 1
23 1676486 2
24 1676954 2
25 1677355
1
26 1960122 2
27 1678696
1
28 1678938
1
29 1678939
1
30 1679227
1
31 1679228
1
32 1700886
1
33 1704682
1
34 1714084
1
35 1919326
1
36 1921319
1
37 1921221
1
38 1921961 6
39 1922234
1
40 1922837 4
41
1923358 10
42 1923362
1
43 1926228
1
44 1927426 2
45 1930641 2
LINER, Rod Guide
GRIP
PIN, Roll, 1/8x
3/4
LOCKWASHER, l/4
CAPSCREW, Hex, 1/4-20 x 3/4
PALNUT
GEAR, Universal
ROD, Chute Control
HANDLE PANEL, Upper
HANDLE PANEL, Lower
SPROCKET, Chute
SPACER
ARM, Shift Assy.
- 5 HP Only
SPRING (Qty. 2 on 7 HP)
SUPPORT, Gear
BRACKET, Control Rod
BUMPER
SPRING
ROD, Clutch
CHAIN
SHIFT ROD, Lower
SHIFT ROD, Upper
- 5 HP Only
SLEEVE, Vinyl
GRIP, Handle
GUIDE, Adj. Rod
SCREW, Special, 5/16-1 8 x
3/4
ARM, Shift Assy. - 7 HP Only
HANDLE, Tube, LH
- Black Finish
HANDLE, Tube, RH
- Black Finish
CLUTCH LEVER ASSY., RH
CLUTCH LEVER ASSY., LH
ROD, Chute, Lower
SHIFT ROD, Upper
- 7 HP Only
KNOB, Spinner
WASHER, 5/1 6
WASHER, 114
CAPSCREW, Hex, 5/16-18 x 1-1/2
CAPSCREW, Hex, 1/4-20 x 1-1/4
CAPSCREW, Hex, 1/4-20 x 5/8
CAPSCREW, Hex, 1/4-20 x l-112
NUT, Centerlock, 1/4-20
NUT, Hex, Centerlock, 5/1 6-l 8
PIN, Roll,
5/32 x 1
SCREW, Thd. Cutting Pan Hd. #10-24
NUT, Hex, Whizlock, 1/4-20
3

Engine
18
NOTE A: Position Belt Guides 1/16" to 1/8" from
belt when idler arm is engaged.
555 Assembly View
XT
.-&See Note A
Torque to 10-14 ft. Ibs.
(2 places)
position Ref. No. 11 1/
I
flush, with hub toward
I
engine.
3b
Install with the hub facing engine on 755 & 7/22E.
Install with the hub away from engine on 555.
Engine Pulley
-
6,13
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.

All Models
Engine
REF.
PART
NO.’ NO. QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
*
*
905121
905850
1667700
1674308
1674312
1674325
1675339
1674328
1677924
1677925
1678600
1678692
1678925
1919326
1921515
1921962
1928691
1931277
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
2
1
2
4
ENGINE, Tecumseh
SWITCH ASSY., Ignition w/keys
KEY, Woodruff,
1/8 x 5/8
KEY, Sq., 3/16x 3/16 x 1
GROUND WIRE
BELT, Traction Drive (5 HP only)
BELT, Auger Drive
PULLEY, Idler (5 HP only)
NUT, Hex, Lock,
5/16-18 (5 HP only)
PULLEY, Engine
GUIDE, Belt
GUIDE, Belt (5 HP only)
BELT, Traction Drive (7 HP only)
PULLEY, Traction Drive (7 HP only)
GUIDE, Belt (7 HP Only)
WASHER,
5/16 (Qty. 3 used on 5 HP)
CAPSCREW, Hex,
5/16-24 x 3/4 (Qty. 1 used on 5 HP)
CAPSCREW, Hex Hd., 1/4-20 x 1-3/4)
SETSCREW, Socket Hd., 5/1 6-1 8 x5/1 6
(Qty. 1 used on Mfg. No. 1691414)
NUT, Hex, Flange Lock, 5/16-18
* See your local Tecumseh dealer for parts &service.
NOTE: Use Simplicity SAE 5W-30 Cold Weather Engine Oil. Part Number 1685576 (12 qts. / case).
5

A-‘*1312
NOTE A: Position Belt Guides 1/16" to
1/8
from Belt when Idler Arm is engaged.
35 -%i@$ 2 Note A
P ’
SeeNoteAHi7 p
See Handle Group
'16 8
/
38
Adjust Shift Guide
(Ref. 19) to obtain proper
3 neutral position.
NOTE B: Position Idler Pulleys (Ref.
Nos. 25
& 8) to outside end of slot.
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
6

All Models
Frame
REF. PART
NO. NO. QTY. DESCRIPTION
1 174870 1
2916169 3
3925160 2
41608310 2
51611743
1
61668477 1
71673911 1
81674297 1
9 1674316
1
10 1674315 1
11 1674318 1
12 1674320 2
13 1675112 1
14 1675114 1
15 1676210 1
16 1676219
1
17 1676220 1
18 1676442
1
19 1676501 1
20 1676508 1
21 1676543 1
22 1677237
1
23 1678694 1
24 1678699
1
25 1685370
1
26 1919326 1
27 1921221 4
28 1921332 4
29 1921969 2
30 1924940
11
31
1925003 9
32 1928731 5
33 1930591 6
34 1930595 2
35 1930645 4
36 1930810 2
37 1931277 4
38 1935255 8
SPACER
PIN, Roll
RIVET
SPACER (7 HP only)
FRAME
PULLEY, Idler, Auger
SPRING, Brake Return
COVER, Belt
IDLER ARM
& BRAKE ASSY. (Incl. Ref. Nos. 21 & 3)
GUIDE, Belt
IDLER ARM ASSY., Traction (5 HP only)
ROD, Idler
MOUNTING PLATE, Transmission
SUPPORT, Transmission
SPRING
BELT GUIDE, LH
BELT GUIDE, RH
PAN, Bottom
GUIDE, Shift
GUARD, Belt (5 HP only)
PAD, Brake
SPACER
IDLER ARM ASSY., Traction (7 HP only)
GUARD, Belt (7 HP only)
PULLEY, Idler
(Incl. Ref. No. 1)
WASHER, 1 1/32
SCREW, Hex,
5/16-18 x 1-1/2 (5 HP only)
CAPSCREW, Hex
Hd., 5/16-18 x 3/4 (7 HP only)
CAPSCREW, Hex,
3/8-16 x 1 -1/2
WASHER
SCREW, Hex, Taptite, 1/4-20 x
1/2 (Qty. 7 on 7 HP)
NUT, Hex, Jam
3/8-16
SCREW, Hex, Flange Lock, 5/1 6-18 x 3/4
SCREW, Hex, Flange Lock, 5/16-18 x 1-1/4
NUT, Hex, Flange Lock,
3/8-16
SCREW, Hex Hd., Taptite 1/4-20 x 1-1/2 (7 HP only)
NUT, Hex, Flange Lock, 5/1 6-18
PALNUT, 5/1 6-18
7

Auger Drive
Torque to 30-34 ft. lbs Hub of pulley to
face auger.
1 14 13 4 **-
-.
Ll
12
@!A
D
16
18-21 ft. Ibs.
6
Auger assy.
stamped "R".
Locate puliey so that
centerline is 1-15/16
from rear of impeller
housing.
Auger assy. stamped "L".
/
Use 1 or 2 washer as
required to eliminate
side-to-side play of
auger in housing.
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
8