Simpnic SiMP Strip User manual

Quick Installation Guide
SiMP Strip
SLS-01-SW

1. Package Content
2. Get Started
2.1 Preparation
2.2 Installation
2.2.1 Length
2.2.2 Connection
2.2.3 Power On
2.2.4 Placement
2.2.5 Concatenation
2.3 Pairing
2.4 Reset
3. FAQ
4. Support

1. Package Content
SiMP Strip (3 meters)
Controller (white)
Adapter (white)
Quick Installation Guide
Warranty Card
SiMP Strip can only work with SiMPNiC SiMP
Keeper. Please make sure you already have SiMP
Keeper. Otherwise SiMP Strip can’t work.

2. Get Started
2.1 Preparation
Get your SiMP Keeper ready and download
SiMPNiC App in advance.
To make SiMP Strip work,you need to set
up SiMP Keeper first.Please refer to SiMP
Home Kit Quick Installation Guide or tutorial
in SiMPNiC App.
You can scan QR code below to download
SiMPNiC App from APP Store (iOS) or
Google Play (Android).

2.2 Installation
2.2.1 Length
First, confirm the length you need to
install. SiMP Strip is in unit of 0.1 meters.
You can tell it by parallel copper mark.
For example, if you need 3.53 meters
long, you have to cut it at 3.6 meters.
Please don’t cut the side near the pin
head, cut the other side. Otherwise the
strip will not illuminate. Next step, use
the double-sided tape to fix the strip
once you confirm and cut the length.

2.2.2 Connection
Second, connect the strip plug (with
pins) with controller (with holes). There
are arrow signs on both device. Make
sure they are aligned.
2.2.3 Power On
Third, connect the controller with
adapter and plug adapter into the
socket. When it illuminates, the work is
done! You can use controller to adjust
the illumination you prefer.

2.2.4 Placement
Make sure the strip is installed flat.
If not, the illumination would be
irregular. Please pay attention to the
corner. Please don’t use SiMP Strip
in environment of extreme heat or
humidity, like kitchen or bathroom.
2.2.5 Concatenation
In few special cases, you might need
to concatenate two strips together.
Please pay attention: only strips
with same spec and voltage can be
concatenated. And the maximum
concatenation length is 6 meters.

2.3 Paring
Pairing SiMP Strip with your SiMP Keeper in
SiMPNiC App.
If your SiMP Strip is from Home Kit,it’s
already in your SiMPNiC App. You can tap
the "Room"icon at the navigation bar and
then you will see it.
Power on SiMP Strip, and you will
see it blinks in white rapidly. It lasts
about 4 minutes long. During this time
period, it’s ready for pairing. If it is not
blinking, refer to "Reset" section to
make it to factory default settings.

① Make sure your smartphone is
connected to Home Wi-Fi (2.4GHz).
② Open SiMPNiC App.
③ Select "Room" icon.
④ Select "+" to add device.
⑤ Select "SiMP Strip".
⑥ SiMP Keeper will beep 2 times and
begin searching. The process lasts
about 45 sec (remember to check SiMP
Strip is blinking during this period).
And then SiMP Strip will appear in the list.
⑦ If SiMP Strip is not found, select
"Cancel" and search again.

2.4 Reset
When power is on, press the side
button of SiMP Strip for 5 seconds. The
blue LED indicator will start blinking, (for
about 4 minutes). During this period of
time, you can pair it.
Attention:
Once you reset, SiMP Strip will return
to factory default settings. Only if
you want remove it from current SiMP
Keeper, otherwise it’s not suggested to
reset.

Q: Why SiMP Strip is illuminating or not
blinking?
A: Normally SiMP Strip illuminates
constantly when power is on. If it
does not illuminate, please reset it
to factory default settings by pressing
the controller button for 5 seconds
and then it starts blinking.
Q: Why SiMP Strip can’t be found in the list?
A: First, make sure SiMP Strip is blinking
before pairing. If it still can not be
found, try to search again.
Q: How do I know SiMP Strip is paired
with SiMP Keeper successfully?
A: If SiMP Strip is paired successfully,
you will see it in your SiMPNiC App
after 45 seconds.
3. FAQ

4. Support
For more product information, FAQ, and
tutorials, please visit SiMPNiC website:
Facebook pageYoutube

For More support, please contact us via
[email protected]

Ver. 201910