Chauvet CUBIX User manual

User Manual

Page 2 of 18 Cubix™ User Manual (Rev. 01a)
TABLE OF CONTENTS
1. Before you Begin............................................................................3
What is Included........................................................................................3
Unpacking Instructions..............................................................................3
Text Conventions......................................................................................3
Icons.........................................................................................................3
Safety Notes .............................................................................................4
2. Introduction.....................................................................................5
3. Setup...............................................................................................6
AC Power..................................................................................................6
Power Linking....................................................................................................6
Mounting...................................................................................................7
Orientation.........................................................................................................7
Rigging..............................................................................................................7
4. Operation ........................................................................................8
Control Panel Operation............................................................................8
Configuration (DMX)..................................................................................8
Starting Address ................................................................................................8
Configuration (Standalone Modes) ............................................................9
Sound Active Mode............................................................................................9
Automatic Mode.................................................................................................9
Manual Mode.....................................................................................................9
Master/Slave Mode..........................................................................................10
DMX Channel Assignments and Values...................................................11
5. Technical Information ..................................................................12
General Maintenance..............................................................................12
General Troubleshooting.........................................................................13
Returns Procedure..................................................................................14
Claims.....................................................................................................14
Contact Information.................................................................................14
DMX Primer ............................................................................................15
Starting Address ..............................................................................................15
Fixture Linking (Daisy Chain)............................................................................15
DMX Cabling ...................................................................................................16
DIP Switch Reference Guide............................................................................17
6. Technical Specifications..............................................................18

Cubix™ User Manual (Rev. 01a) Page 3 of 18
1. BEFORE YOU BEGIN
What is Included
1 x Cubix™
1 x Power Cord
1 x Warranty Card
1 x User Manual
Unpacking Instructions
Immediately upon receiving this product, carefully unpack it and check the container in
which you received it. Make sure that you have received all the parts indicated above
and that they are all in good condition. If the material inside the container (this product
and any other accessory included with it) appears damaged from shipping, or if the
container shows signs of mishandling, notify the shipper immediately. In addition,
retain the container and all the packing material for inspection.
See the Claims section in the “Technical Information” chapter.
Text Conventions
Convention
Meaning
[10]
A DIP switch to be configured
<Menu>
A key to be pressed on the fixture’s control panel
1~512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified (for example, showing the operating
mode/current status)
Menu > Settings
A sequence of menu options to be followed
ON
A value to be entered or selected
Icons
Icon
Meaning
This paragraph contains critical installation, configuration, or operation
information. Failure to comply with this information may render the
fixture partially or completely inoperative, cause damage to the fixture,
or cause harm to the user.
This paragraph contains important installation or configuration
information. Failure to comply with this information may prevent the
fixture from functioning correctly.
This paragraph reminds you of useful, although not critical, information.
Document Information
The information and specifications contained in this document are subject to change without
notice. CHAUVET® assumes no responsibility or liability for any errors or omissions that may
appear in this manual.
© Copyright 2011 CHAUVET®. All rights reserved
Printed in P.R.C.
Electronically published by CHAUVET® in the United States of America
Author
Editor
Manager
PD Manager
A. Chiappone
R. Jones
A. Reiss
F. Sellers

Page 4 of 18 Cubix™ User Manual (Rev. 01a)
Product at a Glance
Use on Dimmer

Auto Programs

Outdoor Use

Auto-ranging Power Supply

Sound Activated

Replaceable Fuse

DMX

User Serviceable

Master/Slave

Duty Cycle

Safety Notes
Please read the following notes carefully because they include important safety
information about the installation, usage, and maintenance of this product.
Keep this User Manual for future consultation. If you sell this product to another
user, be sure that they also receive this document.
Always make sure that the voltage of the outlet to which you are connecting this
product is within the range stated on the decal or rear panel of the fixture.
This product is for indoor use only! To prevent risk of fire or shock, do not expose
this fixture to rain or moisture.
Make sure there are no flammable materials close to the unit while operating.
Always install this product in a location with adequate ventilation, at least 20 in (50
cm) from adjacent surfaces.
Be sure that no ventilation slots on the unit’s housing are blocked.
Always disconnect this product from the power source before cleaning it or
replacing the fuse.
Make sure to replace the fuse with another of the same type and rating.
If mounting this product overhead, always secure it to a fastening device using a
safety cable.
The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate this
product at higher temperatures.
In the event of a serious operating problem, stop using the unit immediately.
Never try to repair this product. Repairs carried out by unskilled people can lead
to damage or malfunction. Please contact the nearest authorized technical
assistance center.
Never connect this product to a dimmer pack.
Make sure the power cord is not crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Never carry a fixture from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
Always avoid direct eye exposure to the light source when this fixture is on.

Cubix™ User Manual (Rev. 01a) Page 5 of 18
2. INTRODUCTION
Safety
Microphone
adjustment
DMX in
Fuseholder
Power in
Power out
DIP switches
DMX out
Microphone
Side Panel
Side Panel

Page 6 of 18 Cubix™ User Manual (Rev. 01a)
3. SETUP
AC Power
This product has an auto-ranging power supply and it can work with an input voltage
range of 100~240 VAC, 50/60 Hz.
To determine the power requirements for a particular fixture, see the label affixed to
the back plate of the fixture or refer to the fixture’s specifications chart. A fixture’s
listed current rating indicates its average current draw under normal conditions.
Always connect this product to a protected circuit (circuit breaker or fuse),
making sure that it has an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect this product to a rheostat (variable resistor) or dimmer circuit,
even if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Power Linking
This fixture provides power linking via the Edison/IEC outlet located in the back of the
unit. Please see the diagram below for further explanation.
Power Linking
Diagram
You can power link up to 26 Cubix™ units on 120 VAC or up to 45 Cubix™ units
on 230 VAC.
The power linking diagram shown above corresponds to the North American
version of this product ONLY! If using this product in other markets, you must
consult with the local CHAUVET® distributor as power linking connectors and
requirements may differ in your country or region.
Generic Fixture Housing
1st Fixture
2nd Fixture
3rd Fixture
Other fixtures

Cubix™ User Manual (Rev. 01a) Page 7 of 18
Mounting
Orientation
The Cubix™ may be mounted in any position, provided there is adequate room for
ventilation around it.
Rigging
Be sure that the structure onto which you are mounting this product can support its
weight. Please see the “Technical Specifications” section of this manual for weight
information.
Make sure to mount the fixture securely to a rigging point, whether an elevated
platform or a truss.
When rigging this product onto a truss, you should use a mounting clamp of
appropriate weight capacity. The bracket has a 13 mm hole, which is appropriate for
this purpose.
When mounting this product overhead, always use a safety cable.
Before deciding on a location for this product, always make sure that it will be easy to
access the unit for maintenance and programming purposes.
When power linking multiple fixtures, you must always consider the length of the
power linking cable and mount the fixtures close enough for the cable to reach them.
The bracket knobs allow for directional adjustment when aiming the fixture to the
desired angle. Only loosen or tighten the bracket knobs using your bare hands. Using
tools could damage the knobs.
Mounting Diagram
Hanging bracket
Bracket knob

Page 8 of 18 Cubix™ User Manual (Rev. 01a)
4. OPERATION
Control Panel Operation
Configuration (DMX)
Set this product in DMX mode to control it with a DMX controller.
1) Connect this product to a suitable power outlet.
2) Turn this product on.
3) Connect a DMX cable from the DMX output of the DMX controller to the DMX
input socket of this product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX
channels the selected DMX mode uses. If you choose a starting address that is too
high, you could restrict the access to some of the fixture’s channels.
The Cubix™ uses one DMX channel in DMX mode, which defines the highest
configurable address to 507.
If you are not familiar with the DMX protocol, you may refer to the “DMX Primer”
section in the “Technical Information” chapter.
To select the starting address, do the following:
1) Set DIP [10] to the ON position.
2) Using DIP switches [1~9], select the starting address.
If you are not familiar with the procedure to configuring DIP switches, please
refer to the DMX Primer section in the Technical Information chapter of this
manual or visit http://www.chauvetlighting.com/chauvet-dip-switch-calculator/.

Cubix™ User Manual (Rev. 01a) Page 9 of 18
Configuration (Standalone Modes)
Set this product in one of the standalonemodes to control it without a DMX controller.
1) Connect this product to a suitable power outlet.
2) Turn this product on.
Sound Active Mode
To enable the Sound Active mode, do the following:
1) Set DIP switch [9] to the ON position.
2) Turn the music on and adjust the microphone sensitivity knob until the fixture
starts reacting to the beat of the music.
The fixture will only respond to the low frequencies of the music (bass and
drums).
Automatic Mode
Never connect a fixture that is operating in any standalone mode, whether
Static, Automatic, or Sound to a DMX string connected to a DMX controller.
This is because fixtures in standalone mode may transmit DMX signals that
could interfere with the DMX signals from the controller.
To enable the Automatic Mode, follow the instructions below:
1) Set DIP switch [8] to the ON position.
Manual Mode
See the chart below for details on manual DIP switch operation. Some DIP switches
may be combined.
Function
DIP switches
1
2
3
4
5
6
7
8
9
10
Red
X
Green
X
Blue
X
RGB Strobe (fast)
X
Center effect
X
Center strobe
(fast)
X
Motor rotation
X

Page 10 of 18 Cubix™ User Manual (Rev. 01a)
Master/Slave Mode
This mode allows a single Cubix™ unit (the “master”) to control the actions of one or
more Cubix™ units (the “slaves”) without the need of a DMX controller. The master
unit will be set to operate in either Automatic or Sound Active mode, while the slave
units will be set to operate in Slave Mode. Once set and connected, the slave units
will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1) Set DIP switch [10] to the ON position.
2) Set the DMX address to “001”, as previously explained.
3) Connect the DMX input of the first slave unit to the DMX output of the master unit.
4) Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
5) Finish setting and connecting all the slave units.
Master unit:
1) Set the master unit to operate in either Automatic or Sound mode, as previously
indicated.
2) Make the master unit the first unit in the DMX daisy chain.
Configure all the slave units before connecting the master unit to the DMX
daisy chain.
Never connect a DMX controller to a DMX string configured for Master/Slave
operation because it may interfere with the signals from the master unit.
Do not connect more than 31 slave units to the master unit.

Cubix™ User Manual (Rev. 01a) Page 11 of 18
DMX Channel Assignments and Values
Channel
Function
Value
Setting
1
Operating mode
000 004
005 028
029 056
057 084
085 112
113 140
141 168
169 197
198 224
225 255
No function
Red
Green
Blue
Blue/green
Red/blue
Green/red
Red/green/blue
Automatic (3-color chase)
Automatic (7-color chase)
2
Strobe
000 004
005 255
No function
Strobe (slow~fast)
3
Motor rotation
000 127
128 255
Rotate clockwise
Rotate bidirectional (fast~slow)
4
Center effect
000 014
015 020
021 026
027 032
033 038
039 044
045 050
051 056
057 062
063 068
069 074
075 080
081 086
087 092
093 098
099 104
105 110
111 116
117 122
123 128
129 134
135 140
141 146
147 152
153 158
159 164
165 170
171 176
177 182
183 188
189 194
195 200
201 206
207 212
213 218
219 224
225 230
231 236
237 242
243 248
249 255
No function
Effect 1
Effect 2
Effect 3
Effect 4
Effect 5
Effect 6
Effect 7
Effect 8
Effect 9
Effect 10
Effect 11
Effect 12
Effect 13
Effect 14
Effect 15
Effec16t
Effect 17
Effect 18
Effect 19
Effect 20
Effect 21
Effect 22
Effect 23
Effect 24
Effect 25
Effect 26
Effect 27
Effect 28
Effect 29
Effect 30
Effect 31
Effect 32
Effect 33
Effect 34
Effect 35
Effect 36
Effect 37
Effect 38
Effect 39
Effect 40
5
Center effect speed
000 015
016 255
Stop
Speed (slow~fast)
6
Center strobe
000 015
016 255
No function
Strobe (slow~fast)

Page 12 of 18 Cubix™ User Manual (Rev. 01a)
5. TECHNICAL INFORMATION
General Maintenance
Dust build up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life and/or mechanical wear. To maintain
optimum performance and minimize wear, you should clean your lighting fixtures at
least twice a month. However, be aware that usage and environmental conditions
could be contributing factors to increase the cleaning frequency.
To clean this fixture, follow the instructions below:
Unplug the fixture from power.
Wait until the fixture is cold.
Use a vacuum (or dry compressed air) and a soft brush to remove dust collected
on the external surface/vents.
Clean all external glass surfaces with a mild soap solution, ammonia-free glass
cleaner, or isopropyl alcohol.
Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.
Softly drag any dirt or grime to the outside of the external glass surface.
Gently polish the external glass surfaces until they are free of haze and lint.
Always dry the external glass surfaces carefully after cleaning them.

Cubix™ User Manual (Rev. 01a) Page 13 of 18
General Troubleshooting
Symptom
Possible Cause
Possible Action
Circuit breaker
or fuse keeps
blowing
Excessive load on the circuit
Make sure that the total load
does not exceed 80% of the
breaker or fuse nominal current
Short circuit along the power
lines
Check the power lines and
power cords
Product does not
power up
No energy on power outlet
Check power outlet
Change to another outlet
Loose or damaged power cord
Check the power cord
Blown fuse
Replace blown fuse with a good
one of the same type and rating
Internal problem
Send product for repair
Fixture does not
respond to DMX
Wrong starting address on the
fixture
Set the correct starting address
on the fixture
Use the right fader(s) on the
controller
Wrong polarity setting on the
DMX controller
Change the signal polarity on
the controller
Loose or damaged DMX cable
Check the DMX cable before
the faulty unit
Internal problem
Send product for repair
Intermittent DMX
Problems
Signal cables are not DMX
compatible
Replace non DMX cables with
true DMX cables
Interference with AC or radio
signals
Keep DMX cables away from
AC wires or radio equipment
DMX cable too long
Install an optically coupled DMX
amplifier right before the fixture
with intermittent problems
Too many fixtures connected
Install an optically coupled DMX
amplifier after unit #32
Terminator not connected
Install a terminator, as indicated
in the “DMX Primer” section.
If you still experience problems after trying the above solutions, contact
CHAUVET® Technical Support.

Page 14 of 18 Cubix™ User Manual (Rev. 01a)
Returns Procedure
The user must send the merchandise prepaid, in the original box, and with its original
packing and accessories. CHAUVET® will not issue call tags.
Call CHAUVET® and request a Return Merchandise Authorization (RMA) number
before shipping the fixture. Be prepared to provide the model number, serial number,
and a brief description of the cause for the return.
The user must clearly label the package with a Return Merchandise Authorization
(RMA) number. CHAUVET® will refuse any product returned without an RMA
number.
DO NOT write the RMA number directly on the box. Instead, write it on a
properly affixed label.
Once you have received the RMA number, please include the following information
on a piece of paper inside the box:
Your name
Your address
Your phone number
The RMA number
A brief description of the problem
Be sure to pack the fixture properly. Any shipping damage resulting from inadequate
packaging will be the customer’s responsibility. As a suggestion, proper UPS packing
or double-boxing is always a safe method to use.
CHAUVET® reserves the right to use its own discretion to repair or replace
returned product(s).
Claims
The carrier is responsible for any damage incurred during shipping to this product or
any part that shipped with it. Therefore, if the received merchandise appears to have
damages caused during shipping, the customer must submit the damage report and
any related claims with the carrier, not CHAUVET®. The customer must submit the
report upon reception of the damaged merchandise. Failure to do so in a timely
manner may invalidate the customer’s claim with the carrier.
For other issues such as missing components or parts, damage not related to
shipping, or concealed damage, the customer must make claims to CHAUVET®
within seven (7) days of receiving the merchandise.
Contact Information
World Headquarters
United Kingdom & Ireland
CHAUVET®
CHAUVET® Europe Ltd.
General Information
Address: 5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Toll free: [phone]
Technical Support
Voice: [phone] (Press 4)
Fax: [phone]
Email: [e-mail]
General Information
Address: Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Email: [e-mail]
World Wide Web
World Wide Web
www.chauvetlighting.com
www.chauvetlighting.co.uk

Cubix™ User Manual (Rev. 01a) Page 15 of 18
DMX Primer
The USITT DMX512-A data transmission protocol (DMX, from now on) is based on
the EIA-485 standard and it has 512 channels (001 to 512). This system requires a
controller (DMX controller), one or more DMX compatible fixtures, and a DMX circuit
(also known as “DMX universe”) to link the fixtures to the controller.
Depending on their complexity and features, DMX compatible fixtures may require
from one to more than 30 DMX channels to operate. Some DMX fixtures have
multiple operation modes (also known as “personalities”), each with its own number
of channels and controllable parameters.
Starting Address
In the DMX system, the controller sends DMX data to each fixture based on the
fixture’s starting address. The starting address is the number of the DMX channel
(001 to 512) assigned to the fixture’s first control channel (Channel 1). When
assigning starting addresses to multiple fixtures, it is critical to ensure that no starting
address is already in use by another fixture to prevent channels from overlapping.
Otherwise, the affected fixtures may operate erratically.
For instance, a user has two DMX compatible fixtures. Fixture “A” has four channels
and fixture “B” has six channels. If the user configures the starting address of fixture
“A” to “001”, channels 001 through 004 on the DMX controller will control fixture “A”.
This means that the user should assign the starting address of fixture “B” to “005” or
higher. For a starting address of “005”, the DMX controller would use channels 005 to
010 to control fixture “B”.
It is possible to control multiple fixtures of the same type by assigning each one of
them the same starting address. In this case, all the fixtures would respond in unison
(synchronized) to the signals from the DMX controller.
Fixture Linking (Daisy Chain)
DMX compatible fixtures receive the control signals
from the DMX controller through the DMX cables.
Each fixture has a DMX In and a DMX Out
connector. The figure to the right illustrates how the
fixtures link to each other using multiple segments of
DMX cable in a sequential format called “daisy
chain”.
The order in which the fixtures connect to the DMX
controller is irrelevant because all fixtures receive
the same DMX signals and they only respond to
them based on their individual starting addresses.
However, it is important to notice that the
connections between fixtures should always be as
short and direct as possible.
To ensure the integrity of the DMX signal, follow the
recommendations of the EIA-485 standard:
The maximum recommended cable length is 500 m (1,640 feet).
The maximum recommended number of fixtures on the same daisy chain is 32.
Connecting more than 32 fixtures on one daisy chain without the use of a DMX
optically-isolated splitter may result in deterioration of the digital DMX signal.
DMX
Controller
1st DMX
Fixture
2nd DMX
Fixture
To other
fixtures

Page 16 of 18 Cubix™ User Manual (Rev. 01a)
DMX Cabling
The DMX protocol requires using special data cables to accommodate for the high
speed digital signals it uses. Despite their apparent similarities, data cables are
electrically different from standard microphone cables because they can carry high
frequency digital signals and have better protection against electromagnetic
interference. You can purchase CHAUVET® certified DMX cables directly from a
dealer/distributor or make your own DMX cable.
If you choose to make your own DMX cable, you must use a data-grade cable such
as the Belden 9841, which has the following electrical characteristics:
Type:
shielded, 2-conductor twisted pair
Maximum capacitance between conductors:
30 pF/ft
Maximum capacitance between conductor and shield:
55 pF/ft
Maximum resistance:
20 ohms/1000 ft
Nominal impedance:
100~140 ohms
DMX Connectors
Each DMX cable must have a male XLR connector on one end and a female XLR
connector on the other end. The DMX protocol indicates that the XLR connectors
must have five pins. However, most lighting fixtures use the 3-pin XLR connector.
The pin assignment of the 3-pin and 5-pin XLR connectors in a DMX cable is as
follows:
Male Plug
Female Plug
Signal
3-Pin
5-Pin
5-Pin
3-Pin
Signal
Common
1
1
1
1
Common
Data -
2
2
2
2
Data -
Data +
3
3
3
3
Data +
Not used
4
4
Not used
Not used
5
5
Not used
You can use the above table to create a 3-pin/3-pin cable, a 5-pin/5-pin cable, or a 3-
pin to 5-pin adapter.
The DMX daisy chain uses a terminator to reduce signal transmission problems,
especially with long cables. The terminator consists of either a 3-pin or 5-pin XLR
male plug with a 120 Ω, ¼ W resistor connected to the wire side of pins 2 and 3, as
shown below.
The terminator plug connects to the DMX Out socket of the last DMX fixture in the
daisy chain.
Do not allow the common wire of the DMX cable to touch the fixture’s chassis
ground. This could cause a ground loop, which may affect your fixtures’
performance. Test all DMX cables with an ohmmeter to verify the correct
polarity of the wires, and to make sure that they are not touching the shield or
each other.

Cubix™ User Manual (Rev. 01a) Page 17 of 18
DIP Switch Reference Guide
You can use the table below to set your fixture’s DIP switches. Imagine that you want
to find the DIP switch settings for DMX address 328:
1) Find 328 among the addresses from the table and point at it with your finger.
2) Move your finger to the left and you will find the settings for DIP Switches 1to 5.
DIP Switches 1, 2, 3, and 5are Off (0), while DIP Switch 4is On (1).
3) Go back and point at the 328 address.
4) Move your finger upward and you will find the settings for DIP Switches 6to 9.
DIP Switches 6and 8are Off (0), while DIP Switches 7and 9are On (1).
5) See below how the DIP Switches will look after configuring them.
DIP Switches
0 = Off
1=Off
#9
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
#8
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
#7
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
#6
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
#1
#2
#3
#4
#5
DMX Address
0
0
0
0
0
-----
32
64
96
128
160
192
224
256
288
320
352
384
416
448
480
1
0
0
0
0
1
33
65
97
129
161
193
225
257
289
321
353
385
417
449
481
0
1
0
0
0
2
34
66
98
130
162
194
226
258
290
322
354
386
418
450
482
1
1
0
0
0
3
35
67
99
131
163
195
227
259
291
323
355
387
419
451
483
0
0
1
0
0
4
36
68
100
132
164
196
228
260
292
324
356
388
420
452
484
1
0
1
0
0
5
37
69
101
133
165
197
229
261
293
325
357
389
421
453
485
0
1
1
0
0
6
38
70
102
134
166
198
230
262
294
326
358
390
422
454
486
1
1
1
0
0
7
39
71
103
135
167
199
231
263
295
327
359
391
423
455
487
0
0
0
1
0
8
40
72
104
136
168
200
232
264
296
328
360
392
424
456
488
1
0
0
1
0
9
41
73
105
137
169
201
233
265
297
329
361
393
425
457
489
0
1
0
1
0
10
42
74
106
138
170
202
234
266
298
330
362
394
426
458
490
1
1
0
1
0
11
43
75
107
139
171
203
235
267
299
331
363
395
427
459
491
0
0
1
1
0
12
44
76
108
140
172
204
236
268
300
332
364
396
428
460
492
1
0
1
1
0
13
45
77
109
141
173
205
237
269
301
333
365
397
429
461
493
0
1
1
1
0
14
46
78
110
142
174
206
238
270
302
334
366
398
430
462
494
1
1
1
1
0
15
47
79
111
143
175
207
239
271
303
335
367
399
431
463
495
0
0
0
0
1
16
48
80
112
144
176
208
240
272
304
336
368
400
432
464
496
1
0
0
0
1
17
49
81
113
145
177
209
241
273
305
337
369
401
433
465
497
0
1
0
0
1
18
50
82
114
146
178
210
242
274
306
338
370
402
434
466
498
1
1
0
0
1
19
51
83
115
147
179
211
243
275
307
339
371
403
435
467
499
0
0
1
0
1
20
52
84
116
148
180
212
244
276
308
340
372
404
436
468
500
1
0
1
0
1
21
53
85
117
149
181
213
245
277
309
341
373
405
437
469
501
0
1
1
0
1
22
54
86
118
150
182
214
246
278
310
342
374
406
438
470
502
1
1
1
0
1
23
55
87
119
151
183
215
247
279
311
343
375
407
439
471
503
0
0
0
1
1
24
56
88
120
152
184
216
248
280
312
344
376
408
440
472
504
1
0
0
1
1
25
57
89
121
153
185
217
249
281
313
345
377
409
441
473
505
0
1
0
1
1
26
58
90
122
154
186
218
250
282
314
346
378
410
442
474
506
1
1
0
1
1
27
59
91
123
155
187
219
251
283
315
347
379
411
443
475
507
0
0
1
1
1
28
60
92
124
156
188
220
252
284
316
348
380
412
444
476
508
1
0
1
1
1
29
61
93
125
157
189
221
253
285
317
349
381
413
445
477
509
0
1
1
1
1
30
62
94
126
158
190
222
254
286
318
350
382
414
446
478
510
1
1
1
1
1
31
63
95
127
159
191
223
255
287
319
351
383
415
447
479
511

Page 18 of 18 Cubix™ User Manual (Rev. 01a)
6. TECHNICAL SPECIFICATIONS
Dimensions and Weight
Length
Width
Height
Weight
13.3 in (337 mm)
10 in (255 mm)
10 in (255 mm)
7.5 lbs (3.4 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100~240 V, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
37 W (0.31 A)
41 W (0.18 A)
Power I/O
Input
Output
Connectors
IEC
Edison/IEC
Cord plug
Edison
N/A
Light Source (tri-color)
Type
Power
Lifespan
LED
3 W (total)
50,000 hours
Color
Current
Red
960 mA
Green
520 mA
Blue
370 mA
Light Source (5 mm)
Type
Size
Current
LED
5 mm
20 mA
Photo Optic
Parameter
Value
Coverage angle
111º
Thermal
Maximum External Temp.
Cooling System
104° F (40° C)
Convection
DMX
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Sockets
6
Ordering
Item Name
Item Number
Item Code
Cubix™
CUBIX
07050334