SITRONICS INTRACOM omniBAS User manual

Next Generation Ethernet
Microwave Backhaul Solution
Installation and
Cabling Manual
Edition 6.0
GDC-002/34
Confidential

INTRACOM TELECOM
19.7 km Markopoulou Ave., Peania, Athens, GR 19002
T [phone], F [phone]
http://www.intracom-telecom.com
email (product support): [e-mail]
The information contained in this document is subject to change without prior notice.
ãINTRACOM S.A. TELECOM SOLUTIONS, 2014. All rights reserved.
All copyright, intellectual and industrial rights in this document and in the technical knowledge it contains
are owned by INTRACOM S.A. TELECOM SOLUTIONS and/or their respective owners.
This document is made available to the end users only for their internal use.
No part of this document nor any data herein may be published, disclosed, copied, reproduced,
redistributed by any form or means, electronically or mechanically, or used for any other purpose
whatsoever without the prior written approval of INTRACOM S.A. TELECOM SOLUTIONS.
Information as well as drawings and specifications contained in this document are subject to change
without prior notice.
All trademarks and copyrights mentioned herein are the property of INTRACOM S.A. TELECOM
SOLUTIONS and/or their respective owners.
Any rights not expressly granted herein are reserved.
Printed in Greece.

Document Revision History OmniBAS -2W/4W/8W
Installation and Cabling Manual - Edition 6.0
Document Revision History
Revisions This page shows the main changes effected in relation to the previous
edition of the OmniBASTM IDU Installation:
Revisions
Previous: 4.0 – 5.1
Current: 6.0
Reasons of
change
The table below shows the reasons for the document change effected in
relation to the previous document edition.
Chapter /
Paragraph
A (Added),
M (Modified) or
R (Removed)
Introduction
Overview of OmniBAS Product Family (page 2):
•New unit added (OmniBASTM-4P).
•New unit for OmniBASTM-4W.
M / A
Installation Material
Installation materials for OmniBAS-4W/8W (page 10). M
New installation materials for new unit OmniBAS-4P (page 14). A
Before Starting the Installation
New Power supply requirements (page 17) for new units OmniBASTM-
4W/4P.
M / A
New Cabling Overview (page 20) for all units. M
Mechanical Installation
New Chassis Overview (page 34) for new unit OmniBASTM-4W. M
New unit added OmniBAS-4P (page 39). A
Cabling Installation
New unit added OmniBASTM-4P (page 55). A
E1 Terminations (pages 60, 63, 66)–New unit added OmniBASTM-4P. A
Cable Characteristics
New cable characteristics for new unit OmniBASTM-4P (pages 73 - 75). A
Appendix-C: Receptacles Pin Out
New receptacles pin-outs added for new unit OmniBASTM-4P (page 95) A

OmniBAS -2W/4W/8W
Installation and Cabling Manual - Edition 6.0
Document Revision History
(Page intentionally left blank)

OmniBAS -2W/4W/8W
Installation and Cabling Manual - Edition 6.0
I
Table of Contents
1Introduction ......................................................................................................................1
About this Document..........................................................................................................1
Overview of OmniBAS Product Family ..............................................................................2
Safety Precautions.............................................................................................................5
2Installation Tools..............................................................................................................6
3Installation Material..........................................................................................................7
OmniBAS-2W.....................................................................................................................7
OmniBAS-4W/8W ............................................................................................................10
OmniBAS-4P....................................................................................................................14
4Before Starting the Installation.....................................................................................16
4.1 Installation Prerequisites..................................................................................................16
4.2 Cabling Overview .............................................................................................................20
Modem Cabling................................................................................................................21
RJ-45 Cabling (Ethernet Payload) ...................................................................................23
RJ-45 Cabling (Outband Management) ...........................................................................24
SFP Cabling (Ethernet Payload) ......................................................................................25
SFP Cabling (STM-1 Payload).........................................................................................26
E1 Cabling (Balanced 120 Ω) ..........................................................................................27
Power Supply Cabling......................................................................................................28
Other Cabling...................................................................................................................29
5Mechanical Installation..................................................................................................32
5.1 OmniBAS-2W...................................................................................................................32
Chassis Overview ............................................................................................................32
IDU Installation.................................................................................................................33
5.2 OmniBAS-4W...................................................................................................................34
Chassis Overview ............................................................................................................34
IDU Installation.................................................................................................................35
5.3 OmniBAS-8W...................................................................................................................37
Chassis Overview ............................................................................................................37
IDU Installation.................................................................................................................38
5.4 OmniBAS-4P....................................................................................................................39
Chassis Overview ............................................................................................................39
IDU Installation.................................................................................................................40
6Cabling Installation........................................................................................................42
6.1 Power Supply Cables.......................................................................................................43
Preparation ......................................................................................................................44
Installation........................................................................................................................48
6.2 IF Tails .............................................................................................................................56
6.3 E1 Terminations...............................................................................................................59
Open End Cables (Balanced 120 Ω)................................................................................59

Table of Contents
II
BNC Terminations (Unbalanced 75 Ω) ............................................................................62
RJ-45 Terminations (Balanced 120 Ω).............................................................................65
6.4 I/O Cables ........................................................................................................................68
6.5 Ethernet Cables ...............................................................................................................70
7Cable Characteristics ....................................................................................................71
7.1 GbE Cable Characteristics...............................................................................................71
OmniBAS-2W...................................................................................................................71
OmniBAS-4W/8W ............................................................................................................72
OmniBAS-4P....................................................................................................................73
7.2 Fast Ethernet Cable Characteristics ................................................................................74
OmniBAS-2W...................................................................................................................74
OmniBAS-4W/8W ............................................................................................................74
OmniBAS-4P....................................................................................................................75
7.3 STM-1 Cable Characteristics ...........................................................................................76
OmniBAS-4W/8W ............................................................................................................76
Appendix-A: Modem Card Installation / Removal ..................................................................77
Appendix-B: I/O Connections ..................................................................................................80
Appendix-C: Receptacles Pin Out ...........................................................................................83
OmniBAS-2W...................................................................................................................83
OmniBAS-4W/8W ............................................................................................................89
OmniBAS-4P....................................................................................................................95
Appendix-D: Open End Cables Color Codes..........................................................................99

Equipment Disposal
Disposal of old electrical and electronic equipment (applicable through
the European Union and other European countries with separate waste
collection systems).
This symbol, found on this product and any of its parts or on its operating
instructions or on its packaging, indicates that electrical and electronic
equipment may not be disposed of as unsorted municipal waste. Instead,
this product should be handed over to applicable collection points for the
recycling of electrical and electronic equipment.
By ensuring the correct disposal of this product, you will help prevent
potential negative consequences to the environment and human health,
which could otherwise be caused by inappropriate disposal of this product.
By recycling, reusing and other forms of recovery of old electrical and
electronic equipment you are making an important contribution to the
conservation of natural resources and to the protection of the environment.
For more information about the recycling of this product, please contact your
local municipal authorities, municipal waste disposal service or the store
where you purchased this product.
Απόρριψη παλαιών ηλεκτρικών και ηλεκτρονικών συσκευών (ισχύει
στην Ευρωπαϊκή Ένωση και άλλες Ευρωπαϊκές χώρες με συστήματα
χωριστής συλλογής απορριμμάτων).
Το σύμβολο αυτό, που απεικονίζεται πάνω στο προϊόν και σε τυχόν
εξαρτήματα του ή στο εγχειρίδιο οδηγιών του ή στη συσκευασία του, δείχνει
ότι οι ηλεκτρικές και ηλεκτρονικές συσκευές, μετά το πέρας της λειτουργίας
τους, δεν θα πρέπει να απορρίπτονται μαζί με τα αστικά απόβλητα. Αντίθετα
θα πρέπει να παραδίδονται σε κατάλληλα σημεία συλλογής για την
ανακύκλωση των ηλεκτρικών και ηλεκτρονικών συσκευών.
Διασφαλίζοντας τη σωστή απόρριψη αυτού του προϊόντος, συνεισφέρετε
στην πρόληψη πιθανών αρνητικών συνεπειών στο περιβάλλον και την
ανθρώπινη υγεία, οι οποίες θα μπορούσαν να προκληθούν από την μη
ενδεδειγμένη απόρριψη του προϊόντος.
Η ανακύκλωση, επαναχρησιμοποίηση και άλλες μορφές αξιοποίησης των
παλαιών ηλεκτρικών και ηλεκτρονικών συσκευών βοηθούν στη διαφύλαξη
των φυσικών πόρων και στην προστασία του περιβάλλοντος.
Για περισσότερες πληροφορίες σχετικά την ανακύκλωση αυτού του
προϊόντος, παρακαλούμε επικοινωνήστε με τις τοπικές δημοτικές αρχές, την
υπηρεσία αποκομιδής αστικών αποβλήτων ή το κατάστημα από το οποίο
αγοράσατε το συγκεκριμένο προϊόν.
Για περισσότερες πληροφορίες, μπορείτε να επικοινωνείτε με το Συλλογικό
Σύστημα Εναλλακτικής Διαχείρισης Αποβλήτων Ηλεκτρικού και Ηλεκτρονικού
Εξοπλισμού “Ανακύκλωση Συσκευών Α.Ε.” (www.electrocycle.gr).

Declaration of Conformity
Hereby, Intracom S.A. Telecom Solutions declares that the
product OmniBAS is in compliance with the essential
requirements and other relevant provisions of the directive
1999/5/EC, and with the requirements of the RoHS directive
2011/65/EU.
For further information, please visit the following URL:
http://emc.intracom-telecom.com/
Δήλωση Συμμόρφωσης
Με την παρούσα, ηIntracom Α.Ε. Τηλεπικοινωνιακών Λύσεων
δηλώνει ότι το προϊόν OmniBAS συμμορφώνεται προς τις
ουσιώδεις απαιτήσεις και τις λοιπές διατάξεις της οδηγίας
1999/5/EC, καθώς και με τις απαιτήσεις της οδηγίας RoHS
2011/65/EU.
Για περισσότερες πληροφορίες γύρω από τη δήλωση
συμμόρφωσης, παρακαλούμε επισκεφθείτε την κάτωθι
ιστοσελίδα:
http://emc.intracom-telecom.com/

OmniBAS -2W/4W/8W
Installation and Cabling Manual - Edition 6.0
1
1 Introduction
About this Document
Scope of
document
This document provides information concerning the installation and cabling
of the following OmniBAS™ Indoor Units (IDUs) units:
•OmniBASTM-2W
•OmniBASTM-4W
•OmniBASTM-8W
•OmniBASTM-4P
Target
Audience
This document is addressed to certified technicians with wireless equipment
knowledge and skills concerning the following:
•Indoor Unit Installation (IDU).
•Addition / Removal of IDU Cards.
•Laying and Installation of Cables.
•Preparation & Termination of: Ethernet, E1, Power cables e.t.c
•Test & Measurement of cables (Ethernet, Optical, Power).
•Equipment Grounding to the Main Grounding System.
Reference
Manuals
The following document for OmniBASTM IDU Installation can be used for
additional product information and are available by Intracom S.A. Telecom
Solutions:
Item Description
1 OmniBAS_ODU_Installation Manual.
2 OSDR_Installation Manual.
Conventions This document applies the following conventions:
This symbol means DANGER. The purpose of this symbol is to
warn you that any wrong action can cause bodily injury or even
death.
This symbol means CAUTION. The purpose of this symbol is to
prevent you from performing an action that might result in damage
of the equipment.
A note calls your attention to important supplementary information.

Chapter 1. Introduction
2
Overview of OmniBAS Product Family
Introduction The OmniBAS™ family of Intracom Telecom IP MW PtP portfolio comprises:
•Split-mount systems:
−OmniBAS™ Indoor Units (IDUs) 1RU / 2RU high and 19″wide.
−OmniBAS™ Outdoor Units (ODUs) & antenna systems.
•All-outdoor system:
−OmniBAS™ OSDR (Outdoor Software-Defined Radio) integrating
everything (baseband / controller / modem / radio) into a robust
enclosure.
This document describes the installation of:
•OmniBAS™ - 2W/4W/8W IDUs for Split-mount system.
•OmniBAS™ - 4P IDU for All-outdoor system.
Continued on next page

OmniBAS -2W/4W/8W
Installation and Cabling Manual - Edition 6.0
3
Overview of OmniBAS Product Family, Continued
OmniBAS™
IDUs
The OmniBAS™ Indoor Units (IDUs) are shown below:
Indoor Unit (IDU) Description
OmniBAS™-2W
It is a Native-IP, 1RU unit
accommodating up to two modems. It
can be positioned at the edge of the
network, or can be used as a repeater
and even as a ring node.
Interfaces:
•2 x GbE (electrical) &
2 x GbE (electrical or SFP)(1)
•- / 16 x E1
OmniBAS™-4W
It is a Native-IP, highly-modular 1RU
indoor unit and is capable of
accommodating in the same chassis
the following cards (identical with
OmniBASTM-8W):
•a combination of 4 modem cards
•one interface card
•one controller card
Modem cards can be flexibly chosen
based on the connection type to the
outdoor unit:
•radio connection to an ODU using
coaxial IF cable
•PonE connection to an all-outdoor
unit (i.e OmniBAS™OSDR) system
using Ethernet cable
Interfaces:
•2 x GbE (electrical) & 4 x GbE (SFP)
•- / 16 / 32 x E1
2 / 4 x STM-1 (VC-12)
Continued on next page
(1) When Dual Media SFPs are installed, then only two out of four electrical GbE interfaces can be used.

Chapter 1. Introduction
4
Overview of OmniBAS Product Family, Continued
OmniBAS™
IDUs, continued
Indoor Unit (IDU) Description
OmniBAS™-8W
OmniBAS™-8W is the base for the
leading CBAN (Converged Backhaul
Aggregation Node) supporting flexibly
all MW technologies appropriate for
HetNets backhauling.
It is a Native-IP, highly-modular 2RU
indoor unit and is capable of
accommodating in the same chassis
the following cards:
•a combination of eight modem cards
•two interface cards
•two controller cards
Modem cards can be flexibly chosen
based on the connection type to the
outdoor unit:
•radio connection to an ODU using
coaxial IF cable
•PonE connection to an all-outdoor
unit (i.e OmniBAS™OSDR) system
using Ethernet cable
Interfaces
•2 x GbE (electrical) & 4 x GbE (SFP),
per control card
•- / 16 / 32 x E1, per interface card
•2 / 4 x STM-1 (VC-12), per interface
card
OmniBAS™-4P
OmniBAS™-4P is an 1RU, half-rack
IDU unit used as an expansion PonE
unit to enable connectivity and control
of up to four all-outdoor units
(OmniBAS™ OSDR).
Interfaces
•4 x GbE (electrical PonE enabled) &
2 x GbE (SFP)
•16 x E1

OmniBAS -2W/4W/8W
Installation and Cabling Manual - Edition 6.0
5
Safety Precautions
PROPER GROUNDING
Never power up the indoor equipment not yet connected to a proper
grounding system.
There is risk of equipment failure and/or electrical shock.
Ensure that the indoor grounding system measures a path resistance less
than 4 Ω.
INDOOR EQUIPMENT PROPER SWITCHING ON / OFF
Never connect or disconnect the power supply cable(s) to or from the
indoor equipment when the local dc power supply source is on.
There is risk of equipment failure.
Ensure the local dc power supply source is off and then connect or
disconnect the power supply cable(s) to or from the indoor equipment.
PROTECTION FROM LIGHTNING
Never leave the IF cable coming from the Outdoor Unit without
adequate lightning protection.
There is risk of equipment failure and/or electrical shock.
Ensure that the IF cable coming from the Outdoor Unit is properly grounded
as described in the Outdoor Radio Equipment Installation Manual (GDC-
001/81 manual code).
ESD PROTECTION
Always use proper antistatic protection (i.e. grounding bracelet,
antistatic bags, etc.) when handling the system cards.
Parts bearing the ESD sign (see left) have ESD sensitive exposed
components.

Chapter 2. Installation Tools
6
2 Installation Tools
Tools List This chapter describes the tools requirements for the proper equipment
installation(1):
Item Photo Description
1
Cros screw drivers:
•(A): PH-1
•(B): PH-3
2
Blade
3
Wire Stripper
4
Cable Jacket Stripper
5
Crimping tool for 1,5 /
2,5 & 4 mm2cable
contact with the
appropriate die
6
Torque wrench 0,8 –
1,13 Nm, 8 mm
7
Hot-air blower
(1) The tools supply is installer responsibility.

OmniBAS -2W/4W/8W
Installation and Cabling Manual - Edition 6.0
7
3 Installation Material
OmniBAS-2W
Package
Contents
The following table depicts the IDU contents for installation:
No Description
1 IDU Factory Test Results Paper.
2 IDU Standard Installation Material.
3 OmniBASTM-IDU.
The package contents is the same for all types of
OmniBASTM-2W IDU’s.
Keep the packaging of the equipment in good condition for
later use (i.e. safe transportation during relocation, return for
repair, etc.).
In case of disposal of the packaging material, it is
recommended to follow the safe disposal procedure
according to local law.
Continued on next page

Chapter 3. Installation Material
8
OmniBAS-2W, Continued
Mounting kit
No Description Qty
(per indoor unit)
1 Screw, M6 x 12 4
2 Washer, od = 15, id = 6,4 4
3 Caged nut, M6 4
IF Tail The following set is supplied per modem card.
No Description Qty
(per indoor unit)
1 IF Tail 1,5m, RG223 SMA-type male, R/A to N-type
female connector 1
(A): O-ring 1
(B): Toothed lock washer 1
2
(C): Nut 1
Continued on next page

OmniBAS -2W/4W/8W
Installation and Cabling Manual - Edition 6.0
9
OmniBAS-2W, Continued
Power
connector
No Description Qty
(per indoor unit)
1 2-pole power connector 2
2 Heat Shrinkable Tube, 10 cm 1
3 Metallic pins for power connector for cable up to 1.5
mm24
4 Metallic pins for power connector for cable up to 2.5
mm24
Tie-wraps
No Description Qty
(per indoor unit)
1 Tie-wraps 45cm, for indoor cables fastening 20
2
The screw and nut included are for connection of
OmniBASTM IDU grounding cable to the rack
grounding terminal
1
Serial Cable for
external alarms
Description Qty
(per indoor unit)
External Alarm Cable 2m, Y-Type,
DB9(Female), DB15(VGA), open end 1 per idu

Chapter 3. Installation Material
10
OmniBAS-4W/8W
Package
Contents
The following table depicts the IDU contents for installation:
OmniBAS-4W OmniBAS-8W
No Description
1 IDU Factory Test Results Paper.
2 IDU Standard Installation Material.
3 OmniBASTM-IDU.
Keep the packaging of the equipment in good condition for
later use (i.e. safe transportation during relocation, return for
repair, etc.).
In case of disposal of the packaging material, it is
recommended to follow the safe disposal procedure
according to local law.
Continued on next page

OmniBAS -2W/4W/8W
Installation and Cabling Manual - Edition 6.0
11
OmniBAS-4W/8W, Continued
Mounting kit
No Description Qty
(per indoor unit)
1 Screw, M6 x 12 4
2 Washer, od = 15, id = 6,4 4
3 Caged nut, M6 4
IF Tail The following set is supplied per modem card.
No Description Qty
(per indoor unit)
1 IF Tail 1,5m, RG223 SMA-type male, R/A to N-type
female connector 1
(A): O-ring 1
(B): Toothed lock washer 1
2
(C): Nut 1
Continued on next page

Chapter 3. Installation Material
12
OmniBAS-4W/8W, Continued
Power
connector
No Description Qty
(per indoor unit)
1 2-pole power connector 2
2 Heat Shrinkable Tube, 10 cm 1
3 Metallic pins for power connector for cable up to 4.0
mm24
Tie-wraps
No Description Qty
(per indoor unit)
1 Tie-wraps 45cm, for indoor cables fastening 20
2
The screw and nut included are for connection of
OmniBASTM IDU grounding cable to the rack
grounding terminal
1
Continued on next page