SKLZ PRO MINI HOOP SYSTEM User manual

IMPORTANT:
SAVE THIS INFORMATION IN THE EVENT
THAT THE MANUFACTURER NEEDS TO BE
CONTACTED FOR REPLACEMENT PARTS.
Thank you for choosing Pro Mini Hoop System. If there is
anything else we can do to help your user experience,
don’t hesitate to send us an email ([email protected])
or give us a call (1-877-225-7275).
SAFETY INSTRUCTIONS:
Always inspect the product prior to and after each use. If you
find any flaw or defect, do not use the Pro Mini Hoop System
and contact Customer Service for a replacement by e-mail
([email protected]) or call (1-877-225-7275).
BEFORE YOU BEGIN:
To ensure safety, do not attempt to assemble this system without
following the instructions carefully. Check entire box and inside all
packing material for parts and/or additional instruction material.
Before beginning assembly, read the instructions and identify
parts using the hardware identifier and parts list in this document.
Proper and complete assembly, use, and supervision are essential
for proper operation and to reduce the risk of accident or injury. A
high probability of serious injury exists if this system is not installed,
maintained and operated properly.
» Check base regularly for leakage. Slow leaks could cause system to
tip over more easily.
» Climate, corrosion or misuse could result in system failure.
» This equipment is intended for home recreational use only and is
not intended for excessive competitive play.
» Read and understand all warning labels affixed to product and in
this instruction manual.
» The life of your basketball pole depends on many conditions. The
climate, placement of the pole, location of the pole, exposure to
corrosives such as pesticides, herbicides or salts are all important.
» If technical assistance is required, contact Customer Service.
» Adult supervision is recommended when adjusting the height.
INSTRUCTION MANUAL

WARNINGS AND CAUTIONS

ADJUSTING THE HEIGHT
MOVING THE PRO MINI HOOP SYSTEM
1 - Hold the Height Adjustment Lever with one hand
and remove the Height Adjustment Pin with
the other.
2 - Move the Height Adjustment Lever to the desired
height, then push the Height Adjustment Pin back
in to lock into place.
1 - Lower the Rim to the lowest position.
2 - Hold the pole and tilt the unit back until the wheels
contact the ground.
3 - Move to the new location.
4 - Slowly tilt the unit back to an upright position.
5 - Make sure the unit is stable before playing.
USAGE TIPS
Pro Mini Hoop System Assembly Guide 3

PARTS INCLUDED & TOOLS NEEDED
COMPONENTS AND TOOLS
1. Axle (2)
2. Wheel (2)
3. Base
4. M8X60 Bolt
5. M8X60 Nut
6. Base Pole
7. Left Support Pole
8. Right Support Pole
9. M8X25 Bolt (2)
10. M8X25 Washer (4)
11. M8X25 Nut (2)
12. M8X50 Bolt
13. M8X50 Nut
14. Center Pole
15. Upper Backboard Bracket
16. Backboard
17. M8X60 SBHCS Bolt (2)
18. M8X60 SBHCS Nut (2)
19. Lower Backboard Bracket
20. M8X40 SBHCS Bolt (2)
21. M8X40 SBHCS Nut (2)
22. Lower Backboard Support Bar (2)
23. Upper Backboard Support Bar (2)
24. M8X85 Bolt (5)
25. M8X85 Nut (5)
26. Long Spacer (2)
27. Top Pole
28. Rim
29. M6X48 RHSN Bolt (3)
30. M6X48 RHSN Nut (3)
31. Height Adjustment Pole
32. Short Spacer (2)
33. Height Adjustment Slider
34. Height Adjustment Pin
35. Net
36. M8 Plastic Washer
37. M8X40 Bolt
38. M8X40 Nut
Not Drawn To Scale
1
15
19
62322
16
28
7
8
14 27
2
26
33 34
32
31
335
M8X60
4 5
M8X25
11
910
36
M8X50
12 13
M8X60 SBHCS
17 18
M8X40 SBHCS
20 21
29
37
30
38
M6X48 RHSN
M8X40
SAND AND/OR WATER 2 ADJUSTABLE WRENCHES
TOOLS YOU WILL NEED FOR ASSEMBLY
M8X85
24 25
3/16 ALLEN WRENCH
4 Pro Mini Hoop System Assembly Guide

ASSEMBLY INSTRUCTIONS
STEP 1
ASSEMBLE BASE
1 - Slide Axle (1) through wheel (2) and push into
wheel well under the Base (3) until it locks into
place. Repeat for other side.
2 - Use M8X60 bolt (4) and nut (5) to attach
Base Pole (6) to Base. HAND TIGHTEN ONLY
UNTIL STEP 6.
3 - Attach Left Support Pole (7) and Right Support
Pole (8) (not shown) to Base (3) using M8X25
bolt (9), two washers (10) and nut (11). HAND
TIGHTEN ONLY UNTIL STEP 6
4 - Using M8X50 bolt (12) and nut (13) attach
Support Poles (7) and (8) to Base Pole (6). HAND
TIGHTEN ONLY UNTIL STEP 6.
5 - Attach Center Pole (14) by sliding it down onto
the Base Pole (6) until it clicks into place. For
lower height, attach Base Pole (6) directly to Top
Pole (27).
6 - With all the above components in place and
fitted together correctly, use wrenches to fully
tighten all bolts and nuts, securing the Base Pole
(6) and Support Poles (7) and (8) to the Base (3).
11
3
22
4
5
7
9
3
10
10
11
6
12 13
14 27
6
6
3
1
2
3
4
5
or
(Base viewed from below.)
(Base viewed from side.)
21
3
4
5
Pro Mini Hoop System Assembly Guide 5

1 - Attach Upper Backboard Bracket (15) to
Backboard (16) using M8X60 SBHCS bolt (17)
and nut (18). Attach Lower Backboard Bracket
(19) to Backboard (16) using M8X40 bolt (20)
and nut (21).
2 - Attach Lower Backboard Support Poles (22)
and Upper Backboard Support Poles (23) using
M8X85 bolts (24), and nuts (25) with a long
spacer (26).
NOTE: When attaching Lower Backboard Support
Poles, align holes furthest from center holes.
3 - Attach Backboard assembly from above to Top
Pole (27) using M8X85 bolts (24), M8 plastic
washers (36) and M8X85 nuts (25).
4 - Attach Rim (28) to Backboard using M6X48 bolts
(29) and nuts (30).
25
ASSEMBLY INSTRUCTIONS
STEP 2
ASSEMBLE BACKBOARD
15
17
18
20
21
17
18
20
21
16
19
22
24
25
24
25
24
36
36
36
36
24
25
27
29
28
30
23
26
26
1
2
3
4
1 2
3
4
6 Pro Mini Hoop System Assembly Guide

ASSEMBLY INSTRUCTIONS
STEP 3
ASSEMBLE BACKBOARD TO BASE
1 - Attach Height Adjustment Pole (31) to Lower
Backboard Support Poles (22) with Short Spacers
(32) using M8X85 bolts (24) and nuts (25).
2 - Slide Height Adjustment Slider (33) from base
of pole over the Top Pole (27) and secure with
Height Adjustment Pin (34) before attaching
Height Adjustment Pole (31) using
M8X40 bolt (37) and nut (38).
3 - Attach entire Backboard assembly to Base
assembly by sliding the Top Pole (27) onto the
Center Pole (14) or Bottom Pole (6) until it clicks.
4 - Attach the Net (35) to the Rim (28) by looping the
long end of the net over the metal loops.
5 - Completely fill Base (3) with sand and/or water
and replace cap before play.
32 25
32
24
31
22
22
27
34
38
37
14
3
33
27
1
2
3
4
5
28
35
WHEN THERE IS NO WEIGHT IN THE BASE, DO NOT LEAVE
UNATTENDED. THE UNIT COULD TIP OVER AND COULD
RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
IF USING WATER IN SUB-FREEZING CLIMATES, ADD ½ GALLON
OF NONTOXIC ANTIFREEZE TO 9½ GALLONS WATER.
CAUTION
6
or 1
2
4
Pro Mini Hoop System Assembly Guide 7

2081 Faraday Ave. Carlsbad, CA 92008 | 877.225.7275 | SKLZ.com Made in China
V15
LIMITED
WARRANTY
REGISTER YOUR PRODUCT AT SKLZ.COM TO ENSURE WARRANTY COVERAGE,
GET NEW PRODUCT INFORMATION AND SPECIAL DEALS FROM SKLZ.
1 YEAR LIMITED WARRANTY. This warranty does not cover damages resulting from accident, misuse, abuse or lost merchandise, and is only valid in the USA. Register your product at SKLZ.com to
ensure warranty coverage, and get new product information and special deals from SKLZ. Questions? Email: [email protected] or call toll free: 877-225-7275
Made in China. ©2014 Pro Performance Sports, LLC. All rights reserved. Manufactured and distributed by SKLZ/Pro Performance Sports: 2081 Faraday Avenue, Carlsbad, CA 92008 U.S.A. SKLZ, SKLZ Pro
Grade, SKLZ Chrome and Sport-Brella are registered trademarks of Pro Performance Sports, LLC., its subsidiaries and affiliates. Product features, appearance, and specifications may be subject to change
without notice. Unauthorized duplication is a violation of applicable local and international laws.
IDEA SUBMISSION
If you have an idea for a new and innovative sports training product,
visit SKLZ.com to submit your concept. Some restrictions may apply.