SKLZ Hit-A-Way PTS Parts list manual

SET-UP & USAGE INSTRUCTIONS
PORTABLE TRAINING STATION

Hit-A-Way® PTS
Hit-A-Way® PTS Instructions For Use
Hit-A-Way PTS Safety Information:
Always wear a helmet:
face guard recommended
Improper use of the Hit-A-Way PTS can result in serious injury. Read
and follow enclosed instructions for the proper and safe use of Hit-
A-Way PTS before you begin:
» Read all set-up and usage instructions carefully. Set-up and proper
positioning are critical for the safe use of your Hit-A-Way PTS.
» Always inspect the Hit-A-Way PTS before using. Do not use if it
appears to be damaged.
» Using a practice bat is recommended. Repetitive use of the
Hit-A-Way may cause damage to wood or high-end lightweight bats.
» Children under the age of 16 should always have an adult present.
» If you swing beyond the ball and sleeve and into the cord, it is
possible to lose control of the bat. While this event is unlikely, it may
result in you striking yourself with the bat. (See page 5 for proper positioning)
» Placing a home plate as a point of reference will help reduce the
likelihood that you will step forward and swing into the cord.
» An upper cut swing increases risk of bat tangling in cord.
» This is a tool to develop form and mechanics.
DO NOT swing aggressively!
Important:
2

Hit-A-Way® PTS
Built-In Wheels
Leg Strap
Retracting Legs
T-latch
Extension Pole
Base Pole
Padded Feet
Hit-A-Way Baseball with
Height-Adjustment Cords
Flexible, Heavy-Duty
Vinyl-Coated Cords
Integrated Upper
Cord Loop
Integrated Lower
Cord Loop
Hit-A-Way PTS Components:
3
SKLZ.com

Hit-A-Way® PTS
2a 2b
1
5
Set-up Instructions:
1. Find and secure a suitable hitting area with approximately
12 feet of free space around pole. Lay the PTS down on the
ground so the T-latch is facing upward. Unclip the leg strap
that is wrapped around the PTS, remove the extension pole
from its holder, and lay it on the side of the PTS base.
2. Turn the T-latch so it is vertical and pull it
out so you see the locking pins (2A).
Turn the T-latch to the horizontal
position. The T-latch is now unlocked
and the locking pins should be resting in
grooves on the outside of the latch (2B).
NOTE: If the T-latch does not pull out fully, move one of the
legs away from the pole to loosen the tension on the spring.
3. Lift the base pole to the standing position, the 3 legs should
slide down the pole as you lift.
NOTE: Make sure the area is clear of children and pets as the
legs may slide down the pole quickly. Make sure your
feet are between two poles when they slide down so
they don’t fall onto you.
4. Once the base pole is positioned with all 3 legs on the
ground, re-lock the T-latch (pull the T-latch out and turn it to the vertical
position and let the locking pins slide back into the spring). Lift the pole
slightly to lock the T-latch back into place. Once you hear a “click”, it is locked.
5. Place the extension pole onto the base pole, using the white
lines as guides to line up the two poles correctly. The
Hit-A-Way cord should not be wrapped around the poles (if so,
the poles are not lined up properly).
4
3

Hit-A-Way® PTS
1
3
INCORRECT CORRECT
“Pitch” Height Adjustment Instructions:
Using Your Hit-A-Way PTS:
1. Wind ball once around pole (clockwise for right handers) and
pull ball and cord toward you. Fully extend cord and set home
plate down (not included) so that the ball is over the center of
the plate. Stand 2 feet back from home plate to hit the ball near
the thick end of the bat. If the bat can reach the adjustment
sleeve or beyond, you’re too close - move back.
2. With the ball centered over home plate, throw ball forward towards imaginary
pitcher until the cord winds up. The Hit-A-Way ball will wind around the
PTS pole 3 times.
3. Wait for the ball to unwind twice and hit the ball. If cords
unwind completely, do not hit the ball; catch it and start
over. This is critical, since swinging into the cord can
cause you to lose control of the bat. Keep hitting as ball
returns. (Do not step toward pole after hitting.)
NOTE: Never stand closer than 2 feet from plate to avoid
bat tangling with cord.
4. Repeat and build a rhythm. You should strive for repeated,
solid contact. Hit continually for a minute and build up the length of your hitting
intervals as you improve.
5
SKLZ.com
Step #1: To lower the ball to your
desired hitting height, pull the
sleeve back, away from the ball
and push the lower cord out of ball
while firmly holding the ball.
Step #2: Pull the excess cord back
through the ball using the upper
cord. (Repeat as desired). Once
the adjustment is made, push the
sleeve back so it butts up against
the ball.
Step #1: Pull the sleeve back, away
from the ball and push upper cord
out of ball. Step #2: Pull excess
cord back through ball using the
lower cord. Once the adjustment
is made, push the sleeve back so it
butts up against the ball.
Lowering the Height Raising the Height

Hit-A-Way® PTS
Storing Your Hit-A-Way PTS:
1. Remove top Pole Extension and lay down on the ground.
2. Unlock the T-latch, turn to the vertical position and pull out. Turn the T-latch
to the horizontal position and let the locking pins rest in grooves.
NOTE: If the T-latch does not pull out fully, lift up on the pole to loosen the
tension on the spring.
3. Pull the PTS base pole down towards the ground, making sure the T-latch
is facing upward. The legs should start to close when pulling the PTS pole
down. Lay on the ground.
4. Lock the T-latch and stand the PTS base
pole upright, wheels on the ground. Slide
the Extension Pole into the peg on the
base and wrap the leg strap around the
PTS and Hit-A-Way cords and clip to lock.
NOTE: To easily transport your PTS leave the
extension pole attached and close
the legs as described above. Grab
the pole and pull the PTS back on its
wheels. You can either push or pull your
PTS to its desired location.
6
4

Hit-A-Way® PTS
7
Replacing the Hit-A-Way Trainer:
Replacement Hit-A-Way trainers for the PTS are available on SKLZ.com or by
calling our toll free number: 1-877-225-7275.
You will need a wrench to replace the Hit-A-Way trainer.
1. Set-up your PTS as if you were going to use it (pg 4).
2. Using the wrench, remove the nut and washers from
the upper and lower integrated cord loop and set
them aside.
3. Pull out the upper loop and slip off the old Hit-A-Way
trainer. Repeat on the bottom.
4. Take the new Hit-A-Way trainer and slip the top cord
loop onto the upper loop. Then slip the bottom cord
onto the lower pole loop. Make sure the you can
properly read the Hit-A-Way logo on the height
adjustment sleeve before attaching the loop back onto
the PTS pole.
5. Slide the upper and lower loops back on to the PTS pole and completely
secure with the washers and nuts using the wrench.
2
3
SKLZ.com

90-DAY LIMITED WARRANTY – HIT-A-WAY® PTS
Pro Performance Sports (PPS) warrants to the original consumer purchaser of any PPS product it
manufactures that the product will be free of defects in materials or workmanship for 90 days (unless
specified in alternate warranties) from the date of purchase. If defective, and purchased from a retail
store, return the product along with receipt to the retail store where the product was purchased. If the
item was purchased from PPS, return the product along with proof of the date of purchase (i.e. the
packing slip), postage prepaid to the address below for replacement consideration:
Pro Performance Sports :: 5823 Newton Drive, Ste. 200 :: Carlsbad, CA 92008 :: Attn: Returns
This warranty does not cover damages resulting from accident, misuse, abuse or lost merchandise. Only
valid in the USA. All returns sent to Pro Performance Sports require a Return Merchandise Authorization
number (RMA). For returns to Pro Performance Sports and for all other Customer Service inquiries,
please call toll free: 1-877-225-7275 Ext. 50.
REGISTER YOUR PRODUCT AT SKLZ.COM TO ENSURE WARRANTY COVERAGE, GET NEW
PRODUCT INFORMATION AND SPECIAL DEALS FROM SKLZ
DO YOU HAVE A WINNING SPORTS PRODUCT OR IDEA?
Visit our web site to learn how to submit a product application for consideration.
It may become our next winning product!
SkLz.cOM
©2010 Pro Performance Sports.
All rights reserved.
Unauthorized duplication is
a violation of applicable laws.
U.S. Patent 6,514,161; 6,296,582;
6,716,119B1
MADE IN CHINA