Skoda Radio Funky User manual

www.skoda-auto.com
Funky: Citigo
Rádio anglicky 05.2013
S00.5610.98.20
1ST 012 095 CR
SIMPLY CLEVER
Radio Funky
Operating instructions

Structure of this Owner's Manual
(explanations)
This Owner's Manual has been systematically designed to make it easy for you to
search for and obtain the information you require.
At the beginning of this manual you will find a table of contents where all the top-
ics are arranged sequentially.
Direction indications
All direction indications such as “left”, “right”, “front”, “rear”, relate to the direction
of travel of the vehicle.
Explanation of symbols
Denotes the end of a section.
Denotes the continuation of a section on the next page.
® Denotes a registered trademark.
Notes
WARNING
The most important notes are marked with WARNING. These WARNING notes
draw your attention to a serious risk of accident or injury.
CAUTION
A CAUTION note alerts you to the possibility of damage to your vehicle (e.g. dam-
age to the gearbox), or points out general risks of an accident.
Note
A normal Note draws your attention to important information about the operation
of your vehicle.

Table of Contents
General information
Important information 2
Device specification and operation 3
MENU mode 4
Radio
Using the system 5
CD player
Using the system 6
External sources
Using the system 8
1
Table of Contents

General information
Important information
Introductory information
These operating instructions describe all possible equipment variants without
identifying them as special equipment, model variants or market-dependent
equipment.
Consequently, this vehicle does not need to contain all of the equipment compo-
nents described in these operating instructions.
The scope of equipment for your vehicle is described in the sales documentation
you were given when purchasing the car. For more information, contact your local
ŠKODA retailer. 
Device operation
The device should only be used when traffic conditions permit safe use.
WARNING
■Concentrate fully at all times on your driving! As the driver, you are fully re-
sponsible for the operation of your vehicle.
■Only use the device in a way that ensures that you are in full control of your
vehicle in every traffic situation - there is a risk of accidents occurring!
■Adjust the volume to ensure that acoustic signals from outside the vehicle,
e.g. sirens from vehicles to give way to, such as the police, ambulance and fire
brigade , can be heard at all times.
■High volumes can cause hearing damage. 
Care of the Display
CAUTION
■Do not use solvents such as benzine or turpentine, which may damage the dis-
play surface.
■Treat the display with care, as finger pressure or contact with sharp objects may
cause dents and scratches on the surface.
Note
The display can be cleaned with a soft cloth and alcohol, if necessary. 
Anti-theft protection
The anti-theft coding of your radio prevents operation of the system after a volt-
age interruption, e.g. during a vehicle repair or following theft. After disconnect-
ing the battery, disconnecting the radio from the on-board voltage of the vehicle
and after a fuse failure, the code must be entered before the vehicle can be used
again.
Enter code
›Switch on the radio with the ignition turned on. SAFE is displayed and then
1000.
›Use the selection buttons 1 - 4 11 to enter the safety code.
›Confirm the safety code by pressing the selection button 6 11 for a longer peri-
od.
Code number
The code number can only be called up “online” via the ŠKODA system, as this
guarantees even more effective anti-theft protection. In this case you will have to
visit a specialist ŠKODA garage.
Incorrect code number
If an incorrect code is confirmed after entry of the code, the procedure can be re-
peated once again. The number of attempts is shown in the bottom screen line.
If the code is entered incorrectly a second time, the unit will be blocked for ap-
prox. one hour. It is only possible to enter the safety code again after one hour
has expired if both the device and the ignition have stayed turned on during that
time. 
2General information

If two invalid attempts are then made again, the unit will be blocked again for an
hour.
The cycle - two attempts, blocked for an hour - will continue to apply.
Note
The code is normally stored in the instrument cluster. This ensures that it is auto-
matically decoded (convenience coding). Manual input of the code is normally not
necessary. 
Device specification and operation
Equipment overview
Fig. 1 Equipment overview
 - On/off knob
›for switching the equipment on and off (press)
›for volume adjustment of audio source currently being played (turn)
Settings knob
›for activating the Scan function
›for settings in the individual modes
RADIO - Radio operation
MEDIA - MEDIA operation
TP - switches traffic programme on/off
1
2
3
4
5
MENU - Setting of the special functions
 and  - buttons for moving forwards/backwards
›RADIO-Mode - for the selection of the stations from the preset list.
›MEDIA-Mode - for the selection of the previous or following track.
›MENU-Mode - for setting the setpoints of special functions
CD case
 - Eject a CD
 - Sound settings
Function keys
›Save and select radio stations
›Enter code
AUX input - Attach an external audio source 
Switching the unit on and off
›To switch the device on and off, press setting button 1.
After switching on the unit, the last audio source that was active before switch-
ing off will be played.
If the device is switched on and the ignition key is removed, the unit switches off
automatically.
If your vehicle is fitted with the KESSY system, the unit will switch off automati-
cally after the engine is turned off and the door opened. If the door is opened be-
fore turning off the engine, the unit will not switch off until the vehicle has been
locked.
When the ignition is switched off, the system switches off automatically after ap-
prox. half an hour (discharge protection of the vehicle battery). 
Volume setting
›To increase the volume, turn button 1 clockwise.
›To decrease the volume, turn button 1 counter-clockwise.
The change to the volume appears in the unit display.
If the volume is reduced to 0, the speakers are muted. The following symbol will
appear in the display .
6
7
8
9
10
11
12
3
General information