manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Skyvue
  6. •
  7. Rack & Stand
  8. •
  9. Skyvue NXG-32 User manual

Skyvue NXG-32 User manual

Other manuals for NXG-32

1

This manual suits for next models

6

Other Skyvue Rack & Stand manuals

Skyvue NXG-32 User manual

Skyvue

Skyvue NXG-32 User manual

Skyvue NXG-55 User manual

Skyvue

Skyvue NXG-55 User manual

Skyvue OBX 32 User manual

Skyvue

Skyvue OBX 32 User manual

Skyvue NXG-55 User manual

Skyvue

Skyvue NXG-55 User manual

Popular Rack & Stand manuals by other brands

Dynex DX-MP3MT Quick setup guide

Dynex

Dynex DX-MP3MT Quick setup guide

Konig & Meyer 24185 manual

Konig & Meyer

Konig & Meyer 24185 manual

ECG LD 326501 instruction manual

ECG

ECG LD 326501 instruction manual

Philips SB7S19S/00 quick start guide

Philips

Philips SB7S19S/00 quick start guide

Woodline KIT-250 lb instructions

Woodline

Woodline KIT-250 lb instructions

ricoo S1222 installation instructions

ricoo

ricoo S1222 installation instructions

Kanto P301 user manual

Kanto

Kanto P301 user manual

VidaBox VB MNT FFS2 installation guide

VidaBox

VidaBox VB MNT FFS2 installation guide

PROEL PLWIN60C user manual

PROEL

PROEL PLWIN60C user manual

AllMounts PLB-43S instruction manual

AllMounts

AllMounts PLB-43S instruction manual

VMP VH-001 instruction sheet

VMP

VMP VH-001 instruction sheet

Nederman SYSTEM 920/400 instruction manual

Nederman

Nederman SYSTEM 920/400 instruction manual

Glasdon ORBIS POST MOUNTING KIT installation guide

Glasdon

Glasdon ORBIS POST MOUNTING KIT installation guide

Songmics LGR105 manual

Songmics

Songmics LGR105 manual

Grape GM401 user manual

Grape

Grape GM401 user manual

FourStarGroup 11225296 manual

FourStarGroup

FourStarGroup 11225296 manual

CHIEF FLR100 installation instructions

CHIEF

CHIEF FLR100 installation instructions

FEC XDCAM EX PMW-EX30 manual

FEC

FEC XDCAM EX PMW-EX30 manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.

In-Ground Post
Assembly Manual
NXG-32 / NXG-42 / NXG-46
In-Ground Post
In-Ground Post Setup
3
InGround Post setuP |
Tools Required for in-ground post Setup:
1. Shovel
2. Post Hole Digger
3. Wheelbarrow and Garden Hoe
(For mixing concrete.)
4. Bag of Concrete Mix
(Amount of concrete will vary,
additional bags may be needed to
complete this installation)
5. Short In-Ground Post Sleeve
6. Mounting Post
and
4All Rights Reserved. 2017 SkyVue®
Assembly Manual- In ground Post
Locate a spot for the post and television.
Dig a square 14”x14” hole like shown below. We recommend that the
hole should have a minimum depth of 24”, however depending on
your location of install depth can or may need to be determined by the
frost line of that area. Please check frost concentration in your location
before installing your in-ground post.
Once the hole is dug, gather your wheelbarrow for concrete mixing.
Be careful when mixing concrete. Wear gloves and eye protection if
possible. Do not handle concrete by hand without gloves as it may
damage or burn the skin.
Concrete Set up
24”
14”
5
InGround Post setuP |
Pour the concrete mix into your
wheelbarrow or mixing container.
Check the packaging for the amount
of water needed to create a mix of
concrete. After measuring, pour the
water into one side of the wheelbarrow
or container. Be sure to measure the
amount of water needed. Most 80
pound bags require no more than 2
quarts of water. Some may require 3.
Using the Garden Hoe, mix the
concrete by scooping and brushing
back and forth. Mix till the concrete
is nice and thick. A good mix should
hold its shape without dripping or
crumbling apart.
Concrete mixture should not be soupy or crumbling. A soupy mixture will
weaken the concrete too much for setting and a crumbling or dry concrete
mixture will not hold together. If your nal mixture is very watery or soupy
then add more concrete mix. For a dry or crumbling nal mixture add minor
amounts of water and then mix to a wet thick concrete.
6All Rights Reserved. 2017 SkyVue®
Assembly Manual- In ground Post
Once your concrete is mixed, have
a friend assist you with pouring.
Pour the concrete mixture to ll
the hole.
Pour slowly and evenly until
concrete mix has reached
ground level.
Once the mixture has been poured
into the hole gather the short post
sleeve to be inserted in the next
step.
Concrete Set up
7
InGround Post setuP |
With assistance insert the short
post sleeve into the center of the
concrete. It’s important that the
post sleeve is inserted straight
down and as level as possible.
Continue to press the sleeve down until the ange is against the concrete
mixture. Place the rubber spacer over top of the ange and proceed to
smooth the surface of the concrete mixture. Make sure to remove any
concrete above the ange as it will conict with the rest of the installation
process.
Once things are set in place, do not continue past this point until
concrete has strengthened and settled. Check the packaging of your mix
to determine the setting time for your concrete base.
Flange
Rubber spacer
NOTE: It’s important that you make sure the sleeve is level before leaving
the concrete to set.
8All Rights Reserved. 2017 SkyVue®
Assembly Manual- In ground Post
With the concrete base set and hardened your post can now be mounted
over the top of the sleeve. Do this by sliding the post down over the
sleeve as shown.
After you position the post insert the swivel locking handle at the hole
located at the lower end of the mounting post.
Congratulations you are now nished with the concrete and post set up
portion of this installation. If you have any questions feel free to contact
our technical support team at (877) 475-9883, option 2.