Skyworks Si4822-DEMO User manual

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
Si4822/26-DEMO
Si4822/26 DEMO BOARD USER’S GUIDE
1. Features
ATDD (analog tune and digital display) FM/AM/SW radio
Worldwide FM band support from 64 to 109 MHz with 5 default sub-bands:
FM1 87–108 MHz (Demo Board Default)
FM2 86.5–109 MHz
FM3 87.3–108.25 MHz
FM4 76–90 MHz
FM5 64–87 MHz (Demo Board Default)
Worldwide AM band support from 504 to 1750 kHz with 5 default sub-bands:
AM1 520–1710 kHz (Demo Board Default)
AM2 522–1620 kHz (Demo Board Default)
AM3 504–1665 kHz
AM4 520–1730 kHz
AM5 510–1750 kHz
Worldwide SW band support from 2.3 to 28.5 MHz with 16 default sub-bands:
SW1 5.6–6.4 MHz (Demo Board Default, for Si4826 only)
SW2 5.95–6.2 MHz
SW3 6.8–7.6 MHz (Demo Board Default, for Si4826 only)
SW4 7.1–7.6 MHz
SW5 9.2–10 MHz (Demo Board Default, for Si4826 only)
SW6 9.2–9.9 MHz
SW7 11.45–12.25 MHz (Demo Board Default, for Si4826 only)
SW8 11.6–12.2 MHz
SW9 13.4–14.2 MHz (Demo Board Default, for Si4826 only)
SW10 13.57–13.87 MHz
SW11 15–15.9 MHz (Demo Board Default, for Si4826 only)
SW12 15.1–15.8 MHz
SW13 17.1–18 MHz (Demo Board Default, for Si4826 only)
SW14 17.48–17.9 MHz
SW15 21.2–22 MHz (Demo Board Default, for Si4826 only)
SW16 21.45–21.85 MHz
Twelve positions band switch or one push button for selecting different band according to the target
application.
Two AAA battery operations with working voltage down to 2.0 V
Economical potentiometer for frequency tuning replaces more expensive variable capacitor (PVC)
Potentiometer and/or push button volume control
FM 50 µs or 75 µs (default) de-emphasis
9-level Bass/Treble via push button control for FM
7-level Bass/Treble via push button control for AM/SW
FM/AM/SW band indicator and frequency display in LCD
2×4 matrix keypad interface
The frequency range of each band, de-emphasis and AM channel space can be re-configured by host MCU.

Si4822/ 26-DEMO
2 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
2. Overview
This manual describes the operation of the Skyworks Solutions Si4822/26-DEMO Board Rev1.0, October 24,
2011. The Skyworks Solutions Si4822/26-DEMO Board is designed with the 24-pin SSOP-packaged Si4822/26
chip, the revolutionary single chip AM/FM/SW receiver that integrates everything from antenna input to audio
output and allows use of common and economical potentiometers to do the frequency tuning. It provides a
complete portable analog tune digital display AM/FM/SW radio design. The LCD displays the tuning information.
The Si4822/26-DEMO is designed with 1-layer PCB, allowing the lowest cost without sacrificing the RF
performance. The demo board works with two AAA batteries and working voltage down to 2.0 V.

Si4822/26-DEMO
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 3
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
3. Description
Figure 1 and Figure 2 shows the physical layout of the board with key components indicated.
Figure 1. Si4822/26-DEMO Board Top Side in Time Mode
Figure 2. Si4822/26-DEMO Board Bottom Side

Si4822/ 26-DEMO
4 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
Power:
BAT1: 2 cells AAA battery compartment
Audio Connectors:
J5: Stereo audio headphone output
Antenna Selections:
AM antenna: Ferrite stick antenna for AM
J6: SMA connector for AM conductive testing
S11: AM antenna selector
J1: BNC connector for FM/ SW conductive testing or FM whip antenna
S12: FM antenna selector
Radio Band Selection:
The demo board provides two methods for selecting the radio band: one is to use the slide switch S2, another is to
use the POWER/BAND button. S14 determines which method is in use.
S14:
1-2: SMA for AM Conductive Test
2-3: AM Ferrite Antenna
3
2
1
1-2: BNC (J1)
2-3: HP ANT (J5)
3
2
1
1-2: Use slide switch to select band
2-3: Use push button to select band
3
2
1

Si4822/26-DEMO
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 5
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
Radio Band Property Setting:
S13:
Audio Output Test Point:
For the general specification test, TP3 is the recommended audio signal test point. The audio test instrument
should be connected to TP3 to get more accurate test results. J5 can also be used as an audio test point, but the
test results may not be entirely accurate under some circumstances.
Main Components:
U1: Skyworks Solutions Si4822/26 AM/FM/SW ATDD receiver
U2: Audio amplifier
U3: MCU
LCD: The digital display of tuning frequency
3
2
1
1-2: Use the keypad to set the band propery via MCU
2-3: Use the tuner default band setting values
2
1GND
AOUT

Si4822/ 26-DEMO
6 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
Control Interface:
VR1: Frequency tuning wheel
VR2: Volume control wheel
S3~S8, S10: The keypad
S2: Band slide switch for FM, AM, and SW
Band definition:
1: FM1 (87–108 MHz), De-emphasis = 75 µs
2: FM5 (64–87 MHz), De-emphasis = 75 µs
3: AM1 (520–1710 kHz), 10 kHz spacing
4: AM2 (522–1620 kHz), 9 kHz spacing
5: SW1 (5.6–6.4 MHz)
6: SW3 (6.8–7.6 MHz)
7: SW5 (9.2–10.0 MHz)
8: SW7 (11.45–12.25 MHz)
9: SW9 (13.4–14.2 MHz)
10: SW11 (15–15.9 MHz)
11: SW13 (17.1–18 MHz)
12: SW15 (21.2– 22 MHz)
Human Interface:
There are seven keys for controlling the demo board as shown below:
Each key can have a different function under each operating condition:
Time mode: Radio function is disabled. LCD displays time. Buttons can be used to set time, alarm, etc.
FM/AM/SW Radio mode: Tuner IC works in Power Up mode. Radio function is enabled. LCD displays the
radio station parameters. Buttons are used to adjust radio settings.
The functions of the buttons are summarized in Table 1. The FM/AM/SW radio parameters that can be configured
are listed in Table 2.
3
2
145 6
789 11
10 12
TREBLE/AL BASS/TMR DE/SPC
SETTING DOWN/VOL- UP/VOL+ POWER/BAND

Si4822/26-DEMO
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 7
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
Table 1. Key Function Description
Button/Mode Time Mode
Tuner Off
FM/AM/SW Radio Mode
Tuner On
POWER/BAND hold Time
< 1s
None Change between FM, AM, and SW (1 FM
band, 1 AM band and 8 SW bands)
hold Time
> 1s
Enable radio Disable radio function and enter Time mode
(Radio parameters will be saved to MCU).
DE/SPC None FM mode: Change De-emphasis, between
50 µs and 75 µs.
AM mode: Change channel space, between
9 kHz and 10 kHz.
BASS/TMR Enter or quit time setting menu. Decrease Bass/Treble level by 1 step.
TREBLE/AL Enable or disable the alarm
function; enter or quit alarm
setting menu.
Increase Bass/treble level by 1 step.
UP/VOL+ hold Time <
1s
In setting menu, change the
current time/alarm parameter
by one unit per each press.
In radio setting menu, change the current
parameter by one unit per each press.
In radio working mode, increase volume 1
step per each press.
hold Time
> 1s
In setting menu, change the
current time/alarm parameter
automatically.
In radio setting menu, change the current
parameter automatically.
In radio working mode, increase volume
level automatically until to maximum.
DOWN/VOL- hold Time <
1s
In setting menu, change the
current time/alarm parameter
by one unit per each press.
In radio setting menu, change the current
parameter by one unit per each press.
In radio working mode, decrease volume 1
step per each press.
hold Time
> 1s
In setting menu, change the
current time/alarm parameter
automatically.
In radio setting menu, change the current
parameter automatically.
In radio working mode, decrease volume
level automatically until to minimum.
SETTING hold Time <
1s
None In radio setting menu, change the selected
item per each press.
hold Time
> 1s
None Quickly return to FM working mode.

Si4822/ 26-DEMO
8 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
Notes:
Tone/VOL mode has four selections:
Bass/treble mode: no digital volume control, fixed volume level at 59
Digital volume mode: no bass/treble effect, volume levels from 0 to 63
Mixed mode 1: bass/treble and digital volume coexist, volume levels from 0 to 63, scale to 0~59
Mixed mode 2: bass/treble and digital volume coexist, volume levels from 0 to 63
The Tuning preference of FM has two selections:
Preference1: When tuning to adjacent channels, the volume level decreases by 2 dB
Preference2: When tuning to adjacent channels, the volume level remains unchanged
The Tuning preference of SW has two selections:
Preference1: When tuning to adjacent channels, the volume level decreases by 2 dB
Preference2: When tuning to adjacent channels, the volume level remains unchanged
There is no tuning preference selection for AM mode.
Table 2. Radio Configuration Parameters
FM Parameter AM Parameter SW Parameter
Bass/Treble: 0-8
Default: 4
Bass/Treble: 1-7
Default: 3
Bass/Treble: 1-7
Default: 3
Digital volume: 0-63
Default: 63
Digital volume: 0-63
Default: 63
Digital volume: 0-63
Default: 63
Band top: max 109 MHz
Default: 108 MHz
Band top: max 1750 kHz
Default: 1710 kHz
Band top: max 28.5 MHz
Default: 6.4/7.6/10/12.25/14.2/15.9/18/22 MHz
for SW1 to SW8 respectively
Band bottom: min 64 MHz
Default: 87.5 MHz
Band bottom: min 504 kHz
Default: 522 kHz
Band bottom: min 2.3 MHz
Default: 5.6/6.8/9.2/11.45/13.4/15/17.121.2 MHz
for SW1 to SW8 respectively
Band range: max 22 MHz Band range: max 2.2 MHz Band range: max 1.1 MHz
De-emphasis: 50 or 75 µs
Default: 75 µs
Channel space: 9 or 10 kHz
Default: 9 kHz
Tone/VOL mode: a-d
Default: d
Tuning preference: a-d
Default: b

Si4822/26-DEMO
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 9
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
4. Operation
The Si4822/26-DEMO board, a complete analog tune and digital display radio, provides two major modes of
operation: Time mode and FM/AM/SW Radio mode.
4.1. Time Mode
Place two AAA batteries into the battery compartment. The board will automatically enter Time mode and display
the time.
The demo board display in Time mode is illustrated in Figure 1.
4.1.1. Time Setting
The time default value is 00:00 and can be set to the correct time manually when needed.
1. In Time mode, press the BASS/TMR button to enter the setting menu. The default is to set the minute item
first. Press this button again to select the hour item. The selected item flashes.
2. While the selected item is flashing, press the DOWN/VOL- and UP/VOL+ button to set the desired time.
3. When you have finished setting the time, press BASS/TMR button to quit the setting menu. The MCU will
automatically quit the setting menu if there is no operation within 2 seconds.
4.1.2. Alarm Setting
1. In Time mode, press the TREBLE/AL button to enable or disable the alarm function and to enter the setting
menu automatically when the alarm is enabled. Once you have entered the setting menu, the default is to
set the minute item first. Pressing this button again will select the hour item. The selected item flashes.
2. While the selected item is flashing, press the DOWN/VOL- and UP/VOL+ button to set the desired time.
3. When you have finished the alarm setting, press TREBLE/AL button to quit the set menu. The MCU will
automatically quit the setting menu if there is no operation within 2 seconds.
4. If the alarm is enabled and the alarm setting time is matched, the radio will be automatically turned on after
the buzzer sounds for 5 seconds.
5. The radio will be turned off and the demo board will go into sleep mode automatically if there is no
operation on the push buttons within 15 minutes; if there is any operation on the push buttons, the auto-
sleep function will be disabled. The radio keeps working throughout this time.

Si4822/ 26-DEMO
10 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
4.2. FM/AM/SW Radio Mode
In time mode, the device will enter FM/AM/SW mode after a long press (hold time > 1s) of the POWER/BAND
button or when the alarm time is reached. The LCD displays the following information: band indicator, band
frequency indicator, and sleep indicator in case the radio is automatically turned on by the alarm.
The demo board display in FM/AM/SW mode is illustrated in Figure 3.
Figure 3. LCD Display in FM Radio Mode
The demo board provides two methods to select the radio band: one is to use the slide switch (S2), the other is to
use the POWER/BAND push button. S14 determines which method is in use.
The demo board also provides two methods to set the band property: one is to use tuner default values, the other
is to use the keypad to reconfigure band property value via the MCU. S13 determines which method is in use. If
you use the tuner default values, the band property is fixed and cannot be re-configured. Refer to Section "4.2.1.
MCU Setting Band Property” for the operation details for setting the band property using the keypad.
To operate the demo board, follow these procedures:
1. According to the desired radio band selection method, set S14 to use the slide switch or push button.
2. According to the desired radio band property, set S13 to use tuner default values or reconfigure the band
property.
3. Hold the POWER/BAND push button (hold time > 1s) or when the alarm time is reached, the device will
enter FM/AM/SW mode.
4. Use slide switch S2 or press the POWER/BAND push button to select the desired band.
5. Refer to section "4.2.1. MCU Setting Band Property” or section "4.2.2. MCU Setting Radio Working Mode”
to reconfigure the band property or radio working mode if necessary.
6. Rotate the tuning wheel and find the desired radio station with the help of the LCD display and/or tuning
indicator D1.
7. Rotate the volume control wheel VR2 and/or press the DOWN/VOL- or UP/VOL+ button to get a
comfortable volume. Press the BASS/TMR or TREBLE/AL button to get the desired bass/treble level.
Notes:
For FM listening, the earphone cable must be connected to the board when S12 is set to HP ANT or an
external antenna must be connected to the BNC connector when S12 is set to BNC.
For AM listening, the ferrite antenna must be connected to the board and the S11 is set to Ferrite before
turning on the radio or switching the band to AM.

Si4822/26-DEMO
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 11
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
4.2.1. MCU Setting Band Property
The demo board provides the function that the band property can be set by the MCU. The band property includes:
Band top
Band bottom
De-emphasis (only for FM)
Channel Space (only for AM)
The setting menu is illustrated in Figure 4.
To set the band properties, follow these steps:
1. Press the SETTING button to enter the setting menu and select the item to be set. The selected item
flashes for 1 second, then automatically switches to its current value.
2. While the value is flashing, press the DOWN/VOL- or UP/VOL+ button to set the desired value within 3
seconds.
3. Repeat step 1 and 2 to finish setting the band properties.
4. When the band properties are set, the MCU automatically quits setting menu if there is no operation within
3 seconds.
5. In FM working mode, press the DE/SPC button to set the De-emphasis 50 µs or 75 µs.
6. In AM working mode, press the DE/SPC button to set the Channel Space 9 kHz or 10 kHz.
Figure 4. Setting Menu
SETTING MENU:
1 BAND TOP
2 BAND BOTTOM
3 TONE/VOL MODE
4 Tuning preference
a preference1
b preference2
a Bass/Treble MODE
b Dig-Vol MODE
c MIX MODE1
d MIX MODE2

Si4822/ 26-DEMO
12 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
4.2.2. MCU Setting Radio Working Mode
The host MCU can set the radio working mode. The working mode includes:
Tone/volume mode (only for FM mode), item 3 in setting menu
Tuning preference (only for FM and SW), item 4 in setting menu
To set radio working mode, follow these steps:
1. Press the SETTING button to enter the item 3. The LCD displays the item number st3 for 1 second, then
automatically switches to its mode indication.
2. Press the DOWN/VOL- or UP/VOL+ button to select the desired mode within 3 seconds.
3. Repeat step 1 and 2 to set the tuning preference by setting the item 4.
4. When the radio working mode is set, the MCU automatically quits the setting menu if there is no operation
within 3 seconds.

Si4822/26-DEMO
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 13
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
5. Bill of Materials
ATDD AM/FM/SW receiver IC Si4822/26 with external 32.768 kHz crystal oscillator support
LM4910MA Audio amplifier IC
TM8795 MCU
See Table 3 for details
Table 3. Si4822/26-DEMO Board Bill of Materials Rev 1.0
Item Qty Reference Description Value
1 12 C1-2 C6 C19 C24 C37-42 C44 CAP,SM,0603,X7R 0.1 µ
2 2 C5 C36 CAP,SM,0603,X7R 0.47 µ
3 2 C8 10 CAP,SM,0603,COG 100 p
4 1 C33 CAP,SM,0603,COG 10 p
5 4 C28-29 C32 C35 CAP,SM,0603,COG 22 p
6 1 C11 CAP,SM,0603,X7R 330 p
7 2 C30-31 CAP,SM,0603,X7R 33 n
8 1 C34 CAP,SM,0603,COG 33 p
9 1 C15 CAP,SM,0603,X7R 4.7 µ
10 2 C4 C12 CAP,SM,0603,X7R 10 µ
11 1 C13 CAP,SM,1210,X7R 47 µ
12 1 C18 CAP,SM,0603,X7R 820 p
13 2 C23 C27 CAP,SM,1210,X7R 220 µ
14 2 C14 C25 Electrolytic capacitor 100 µ/4 V
15 1 C3 Electrolytic capacitor 220 µ/4 V
16 2 R5-6 RES,SM,0603 2 k
17 1 R27 RES,SM,0603 100 R
18 1 R34 RES,SM,0603 100 k
19 1 R32 RES,SM,0603 10 R
20 2 R3 R42 RES,SM,0603 10 k
21 1 R41 RES,SM,0603 120 k
22 1 R22 RES,SM,0603 12 k
23 2 R1-2 RES,SM,0603 1 M
24 2 R4 R31 RES,SM,0603 1 k

Si4822/ 26-DEMO
14 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
25 1 R24 RES,SM,0603 200 R
26 1 R13 RES,SM,0603 22 R
27 1 R16 RES,SM,0603 2.2 k
28 1 R20 RES,SM,0603 6.8 k
29 1 R21 RES,SM,0603 NP
30 1 R7 RES,SM,0603,Tolerance ±1% 10 k 1%
31 1 R29 RES,SM,0603,Tolerance ±1% 160 k 1%
32 9 R9-12 R14-15 R28 R33 R35 RES,SM,0603,Tolerance ±1% 20 k 1%
33 1 R43 RES,SM,0603,Tolerance ±1% 30 k 1%
34 1 R36 RES,SM,0603,Tolerance ±1% 33 k 1%
35 1 R8 RES,SM,0603,Tolerance ±1% 40 k 1%
36 1 R44 RES,SM,0603,Tolerance ±1% 47 k 1%
37 1 U1 SI4822/26 SSOP24 Si4822/26
38 1 U2 LM4910MA,SO8 LM4910MA
39 1 U3 TM8795 44 PIN TM8795 44 PIN
40 1 Q2 TRANSISTOR NPN SOT23 2N3904
41 1 Q1 TRANSISTOR NPN SOT23 2SC9018
42 1 Q3 TRANSISTOR NPN SOT23 2N3906
43 2 D2 D4 DIODE,SM,ESD,SOT23 BAV99
44 3 B4 B5 B6 FERRITE BEAD,SM,0603 2.5 k/100 M
45 1 B1 FERRITE BEAD,SM,0603 NP
46 1 BZ1 BUZZER BUZZER
47 2 Y1-2 CRYSTAL 32.768 kHz
48 1 D1 LED LED
49 1 D6 1N4148 1N4148
50 1 J5 Stereo earphone jack with switch 3.5 mm
51 1 L1 RES,SM,0603 0R
52 1 L3 IND,SM,0603 120 nH
53 1 TP3 CONN,TH,1x2,HDR CONN,TH,1x2,HDR
Table 3. Si4822/26-DEMO Board Bill of Materials Rev 1.0 (Continued)
Item Qty Reference Description Value

Si4822/26-DEMO
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 15
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
54 1 LCD1 LCD LCD
55 1 J1 BNC VERTICAL BNC for FM testing
56 1 J6 SMA VERTICAL SMA for AM testing
57 1 ANT1 AW ferrite stick antenna 220 µH
58 1 BAT1 BATTERY BOX ,AAA*2 SIZE
59 4 S11-14 One pole two throw switch
60 1 S2 Single pole twelve throw switch
61 8 S1 S3-8 S10 Push button
62 1 VR1 100 k, ±10%,Variable resistor(POT) 100 k
63 1 VR2 10k,±20%,Variable resistor(POT) 10 k
Table 3. Si4822/26-DEMO Board Bill of Materials Rev 1.0 (Continued)
Item Qty Reference Description Value

Si4822/ 26-DEMO
16 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
6. Schematics and Gerber
FM1 (87MHz - 108MHz) FM5 (64MHz - 87MHz)
AM1 (520kHz - 1710kHz)
FM/SW
MW
Si4822/26-A
AM2 (522kHz - 1620kHz)
SW1 (5.6MHz - 6.4MHz)
SW3(6.8MHz - 7.6MHz) SW5(9.2MHz - 10.0MHz) SW7(11.45MHz - 12.25MHz) SW9 (13.4MHz - 14.2MHz)
SW11 (15MHz - 15.9MHz) SW13 (17.1MHz - 18MHz)
SW15 (21.2MHz - 22MHz)
Audio output
S13: Band property
2-3 Tuner default 2-1 MCU Setting S14: Band Selection
2-3 slide switch 2-1 push button
Test point
Aout
GND
C39
0.1u BAT1
AAA*2
12
3 4 5 6 7 8 9 10 11 12 13
S2
R15
20k 1%
R10
20k 1%
R12
20k 1%
R11
20k 1%
R14
20k 1%
R9
20k 1%
R7
10k 1%
R8
40k 1%
R28
20k 1%
R29
160k 1%
J1
C19
0.1u
C15
4.7u
VR1
100k 10%
C6
0.1u
D4
BAV99
C5
0.47u
Q1
2SC9018
R31 1k
R32 10R
C30
33n
C33
10p
R41
120k
C31
33n
B6
2.5k/100M
C36
0.47u
ANT1
MW ferrite antenna
J6
D2
BAV99
R34
100k
C34
33p
1
LNA_EN
2
IRQ
3
TUNE1
4
TUNE2
5
BAND
6
NC
7
NC
8
FMI
9
RFGND
10
NC
11
NC
12
AMI
13 GND
14 GND
15 RST
16 SDIO
17 SCLK
18 XTA LO
19 XTA LI
20 VDD1
21 VDD2
22 DBYP
23 NC
24 AOUT
U1
C1
0.1u
R27
100R
R33
20k 1%
R35
20k 1%
R36
33k 1%
C13
47u
R43
30k 1%
R44
47k 1%
C14
100u/4V
L1
0R/120nH
C4
10u C12
10u
VR2-A
1 2 3
J5
C24 0.1u
R20 6k8
R22
12k
B4 2k5/100M B5 2k5/100M
1IN1 2IN2 3SHUTDOWN 4GND 5
VDD
6
VO3
7
VO2
8
VO1
U2
LM4910MA
C10
100p
C11 330p
R16
2k2
C18
820p
C23
220u
C27
220u
C8
100p
B1
NC
C25
100u/6.3V
Y1
32.768KHz
C28
22p
C29
22p
R3
10k
R21
NC
R42
10k
S11
1
23
S13
1
2
3
S14
R5
2k
R6 2k
L3
120nH
TP1
S12
TP3
VCC
BAND [1]
LNA_EN[1]
LNA_EN [1]
BAND
[1]
TUNE1
[1]
TUNE1 [1]
RESET [2]
VCC
VCC
VCC
FMI
[1]
IRQ[2]
SCLK [2]
SDIO [2]
VCC
XTA LI
[2]
FMI
[1]
VCC
SHUTDOWN [2]
VCC
Figure 5. Si4822/26-DEMO Board Rev 1.0 Schematic—Radio and Audio Portions

Si4822/26-DEMO
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 17
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
DIVISION
DRAWN
APPD
DATE
MODEL NO
DATE
October.24.20
SI4822/26-DEMO
MCU LCD
KEY BUZZER
Jing Wang
1 BAND TOP 2 BAND BOTTOM
3 TONE/VOL MODE
d MIX MODE2
c MIX MO DE1 b Dig-Vol MODE
a Bass/Treble MODE
SETTING MENU:
b preference2 a preference1
4 Tuni ng preference
S5
BASS/TMR
S3
POWER/BAND
S4 DE/SPC S6
TREBLE/AL
S7
UP/VOL+
S8
DOWN/VOL-
S10
SETTING
BZ1
Q2
2N3904
R4
1k
D6
1N4148
C2
0.1u
C3
220u/4V
R13 22R
MHz
SWMW
FM
SLEEP
KHz MHz
PM
1
COM1
2
COM2
3
COM3
4
SEG0
5
SEG1
6
SEG2
7
SEG3
8
SEG4
9
SEG5
10
SEG6
11
SEG7
12
SEG8
13
SEG9
14
SEG10
15
SEG11
16
SEG12
17
SEG13
LCD1
1BAK 2XIN 3XOUT 4GND 5VDD1 6VDD2 7VDD3 8CUP1 9CUP2
10 COM1 11 COM2
12 COM3
13 COM4
14 COM5
15 SEG1(K1)
16 SEG2(K2)
17 SEG3(K3)
18 SEG4(K4)
19 SEG5(K5)
20 SEG6(K6)
21 SEG7(K7)
22 SEG8(K8)
23
SEG9(K9)
24
SEG10(K10)
25
SEG11(K11)
26
SEG12(K12)
27
SEG21
28
SEG22
29
SEG23
30
SEG24/IOA1
31
SEG25/IOA2
32
SEG26/IOA3
33
SEG27/IOA4
34
SEG28/IOB1/ELC
35
SEG29/IOB2/ELP
36
SEG30/IOB3/BZB
37
SEG31/IOB4/BZ
38
SEG32/IOC1/KI1
39
SEG33/IOC2/KI2
40
SEG34/IOC3/KI3
41
SEG35/IOC4/KI4
42
RESET
43
INT
44
TEST
U3
Y2
32.768KHz
C32 22p C35 22p
C37
0.1u
C38
0.1u
C40 0.1u
Q3 2N3906
R1
1M
R2
1M
C41 0.1u
S1
RESET
C42 0.1u
C44
0.1u
D1
Tuning indicator R24
200R
KEY_ R1 [2]
KEY_ C3 [2] KEY_ C1 [2] KEY_ C0 [2]
KEY_ C2 [2]
KEY_ R0 [2]
BZ [2]
VCC
LCD_C1
[2]
LCD_C2
[2]
LCD_C3
[2]
LCD_S0
[2]
LCD_S1
[2]
LCD_S2
[2]
LCD_S3
[2]
LCD_S4[2]
LCD_S5
[2]
LCD_S6
[2]
LCD_S7
[2]
LCD_S8[2]
LCD_S9
[2]
LCD_S10
[2]
LCD_S11
[2]
LCD_S12
[2]
LCD_S13
[2]
LCD_C1 [2] LCD_C2 [2]
LCD_C3 [2]
KEY_ R0 [2]
KEY_ R1 [2]
LCD_S0 [2]
LCD_S1 [2]
LCD_S2 [2]
LCD_S3 [2]
LCD_S4 [2]
LCD_S5 [2]
LCD_S6
[2]
LCD_S7
[2]
LCD_S8
[2]
LCD_S9
[2]
LCD_S10
[2]
LCD_S11
[2]
LCD_S12
[2]
SDIO
[1]
RESET
[1]
SCLK
[1]
LCD_S13
[2]
BZ
[2]
KEY_ C0[2]
KEY_ C1[2]
KEY_ C2[2]
KEY_ C3[2]
IRQ [1]
VCC
VCC
VCC
XTA LI [1]
VCC
SHUTDOWN[1]
Figure 6. Si4822/26-DEMO Board Gerber Rev 1.0 Schematic—MCU Portion

Si4822/ 26-DEMO
18 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
Rev. 0.1 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 10, 2021
Figure 7. Si4822/26-DEMO Board Gerber Rev 1.0

Copyright © 2021 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the
information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer.
Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation,
products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or
information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability
for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or
materials, except as may be provided in Skyworks’ Terms and Conditions of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR
OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY
INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR
COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR
ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT
LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT
OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks
products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such
applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of
design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating
safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any
equipment resulting from the use of Skyworks products outside of Skyworks’ published specifications or parameters.
Skyworks, the Skyworks symbol, Sky5®, SkyOne®, SkyBlue™, Skyworks Green™, Clockbuilder®, DSPLL®, ISOmodem®, ProSLIC®, and SiPHY®are trademarks or
registered trademarks of Skyworks Solutions, Inc. or its subsidiaries in the United States and other countries. Third-party brands and names are for
identification purposes only and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at
www.skyworksinc.com, are incorporated by reference.
Portfolio
www.skyworksinc.com
Quality
www.skyworksinc.com/quality
Support & Resources
www.skyworksinc.com/support
Connecting Everyone
and Everything,
All the Time
Skyworks Solutions, Inc. | Nasdaq: SWKS | [email protected] | www.skyworksinc.com
USA: 781-376-3000 | Asia: 886-2-2735 0399 | Europe: 33 (0)1 43548540 |