Funtronix SC-200 User manual

Copyright © 2017 Funtronix LLC. All rights reserved
1
SC-200 6-INCH SHOT CLOCKS
SC-1200 12-INCH SHOT CLOCKS
FUNTRONIX
Dual Wireless Shot Clock
Systems
OPERATING MANUAL
Model SC-200 with 6-inch displays
Model SC-1200 with 12-inch displays
Revision January 25, 2017

Copyright © 2017 Funtronix LLC. All rights reserved
2
Thank you for purchasing the Funtronix wireless shot clock system. At Funtronix, our motto is
“Electronic Fun for Everyone”. Our goal is to add a little fun to your sports and leisure activities.
The contents of the package may contain parts and packing materials that can be hazardous to
children under 3 years old. Assembly of these components must to be performed with adult
supervision.
While the AC adapter is UL approved, the input-side plugs into a standard high-voltage AC outlet.
Care should be taken to not make physical contact with the power supply plug area.
Before using your new shot clock system, please read the following precautions. Doing so will
reward you with many years of enjoyment with your new wireless shot clocks. Failure to follow
them may cause bodily harm or may damage the pager beyond the terms of the warranty.
1. DO NOT expose the shot clocks or keypad to rain or other condensing moisture.
2. DO NOT store the shot clocks or keypad in direct sunlight for extended periods of time.
3. DO NOT drop or hit the shot clocks, as this may result in injury and/or void the warranty.
4. DO read the entire owner’s manual so that you will utilize the full potential and versatility of your
wireless shot clock system.

Copyright © 2017 Funtronix LLC. All rights reserved
3
TABLE OF CONTENTS
SECTION DESCRIPTION PAGE
1 Initial Setup 4
2 Using Your Shot clocks 5
3 Charging the keypad 6
4 Charging the rechargeable scoreboard battery 7
5 Pairing the wireless keypad and shot clocks 8
6 Detailed Specifications 8
PACKAGING CONTENTS
ITEM QUANTITY DESCRIPTION
1 2 Shot clock Unit
2 1 Wireless keypad Remote Control
3 1 Keypad Lanyard
4 1 Keypad charging adapter
5 1 Owner’s Manual
Optional Accessories:
(2) Rechargeable Scoreboard Batteries, Model BT-12V-7A
(2) Battery Chargers for BT-12V-7A, Model CHG-800
(2) AC adapters, Model PS-12V-3000

Copyright © 2017 Funtronix LLC. All rights reserved
4
SECTION 1: Initial SETUP
Charge the keypad as instructed in SECTION 3.
For SC-200 ONLY:
Insert 8 c-size alkaline batteries into each shot clock, or use the optional AC adapter (not
included) to power the shot clock displays.
Extend the swivel foot support found on the bottom of the shot clocks. Set the shot clock(s) on
a stable surface.
For SC-1200 ONLY:
Charge the rechargeable scoreboard batteries (if included) as instructed in SECTION 4.
Attach the rechargeable batteries to the back of the shot clock displays as shown below:
Attach the rechargeable battery as shown
or
Plug the shot clock displays into wall outlets using the AC adapters (if included), Model PS-
12V-3000. Plug each AC adapter into the connector located below the power switch found on
the back of the each shot clock display.
For both SC-200 and SC-1200 models:
Turn the shot clocks on using the power switch located on the back of each shot clock display.
Proceed to SECTION 2 for details regarding the use of your shot clock system.

Copyright © 2017 Funtronix LLC. All rights reserved
5
SECTION 2: USING YOUR SHOT CLOCKS
Refer to the keypad image below for instructions on how to use your shot clock.
You can adjust the shot clocks from 1 to 99 seconds, and this time will be stored in the shot clocks even
when power is turned off. To set the shot clocks, follow these steps:
1. With both shot clocks on, press and release the “RESET/HOLD” button.
2. Adjust the “reset” shot clock time using the ADJUST buttons.
3. Press the “START” button to start the clocks and the “STOP” button to stop the clocks.
4. Pressing the +/- ADJUST buttons after the shot clocks have already been started (but not
immediately after pressing the “RESET/HOLD” button) will allow you to adjust the current time on
the shot clock without affecting the reset time of the shot clocks.
Note: To guarantee that both shot clocks remain in-sync with each other, always turn them both on
prior to pressing any buttons on the keypad. If the shot clocks do not show the same time, follow
these steps to sync them back up:
1. Make sure the shot clocks are turned on and stopped.
2. Press and release the “RESET/HOLD” button.
3. Note the time on one of the shot clocks (let’s call it the first shot clock), then turn this shot clock off.
4. Adjust the time on the other (second) shot clock to match the first shot clock.
5. Turn the first shot clock back on.

Copyright © 2017 Funtronix LLC. All rights reserved
6
SECTION 3: CHARGING THE KEYPAD BATTERY
The wireless keypad contains a rechargeable battery. While the charge of the keypad battery will typically
last between 1 to 2 weeks (depending on usage), we recommend charging your keypad the night before
each use of the scoreboard.
The charging indicator will light up orange to indicate the keypad is charging. The light will turn green
once the keypad is fully charged.
Plug keypad charger into 120VAC wall outlet

Copyright © 2017 Funtronix LLC. All rights reserved
7
SECTION 4: CHARGING THE RECHARGEABLE SCOREBOARD BATTERY
WARNING: Pursuant to California Proposition 65, the battery contains chemicals known to the
State of California to cause cancer and birth defects or other reproductive harm. Wash hands after
handling.
1. Only charge the battery in a well-ventilated area.
2. Only use the charger with the battery that was included with your scoreboard.
3. Do NOT charge the battery if it has any physical damage to its casing, such as cracks or
punctures, or other visible damage.
4. Do NOT use the charger if it has received a sharp blow, been dropped, or is otherwise
damaged in any way.
5. Do NOT use an extension cord with the charger.
6. Operate the charger as far away from the battery as the charger’s cable length permits.
7. Do NOT charge the battery near any flammable materials, such as carpets, upholstery, paper,
cardboard, etc.
8. Do NOT smoke or allow sparks or flames in the vicinity of the battery.
9. Never charge a frozen battery.
10. Never set a battery on top of the charger.
11. Never place the charger above a battery being charged – gases from the battery may corrode
and damage the charger.
12. Never short the battery contacts together.
13. Do NOT operate the charger with damaged cord or plug.
14. Keep out of reach of children.
Follow the steps below to charge your battery.
1. Do NOT plug the charger into the AC outlet just yet – leave it unplugged until step 4.
2. Disconnect the battery’s power cable from the scoreboard.
3. Plug the battery’s power cable into the charger’s mating power connector.
4. Plug the charger’s power cable into a standard 120VAC wall outlet.
5. When charging is complete, first unplug the charger from the wall outlet before unplugging the
charger from the battery.
The charger’s status lights will light up depending on various conditions. See details below:
Red light is flashing Battery cable polarity is reversed. Correct the
connection before continuing
Yellow/Orange light is lit The battery is charging
Yellow/Orange light is flashing The charging process has been aborted
Green light is lit/pulsing The battery is fully charged and the charger is in ‘maintain’ mode to keep the battery fully charged until it
is used.

Copyright © 2017 Funtronix LLC. All rights reserved
8
SECTION 5: PAIRING THE WIRELESS KEYPAD AND SHOT CLOCKS
If either shot clock is showing a rotating pattern on its screen, this is an indication that it is not
paired to the keypad. Follow the steps below to reconnect the keypad and shot clocks together.
1. If the keypad had previously been paired to the shot clocks, you must first perform a step to
delete any old connections within the keypad. To do this, press and hold both the “START”
and “STOP” buttons simultaneously for several seconds – until the keypad emits 5 beeps in
a row. It is important to press both of these buttons at the exact same time and hold them
down for this step to work.
2. Make sure both shot clocks are displaying a rotating pattern on their screens. If they are
not, cycle power on and off on the shot clock repeatedly (waiting 2 seconds in each ‘on’ and
‘off’ state) until the rotating pattern is displayed.
3. Make sure only one shot clock is turned on and showing the rotating pattern. The other
shot clock needs to be off to connect the first shot clock.
4. Press and hold the “CONNECT 1” button on the keypad until the keypad beeps once. The
first shot clock will show it is connected after a few seconds.
5. Leave the first shot clock turned on.
6. Turn on the second shot clock.
7. Press and hold the “CONNECT 2” button on the keypad until the keypad beeps once. The
second shot clock will show it is connected after a few seconds.
8. You are now ready to use your shot clocks.
SECTION 6: PRODUCT SPECIFICATIONS
(Specifications subject to change without notice)
FUNCTIONAL SPECIFICATIONS
Keypad Operating Range: Up to 400 feet from Shot clock displays.
ELECTRICAL SPECIFICATIONS
Operating Voltage: +12 volts DC.
Operating Current: 200/250 mA (low brightness)
(SC-200/SC-1200): 400/600 mA (high brightness)
MECHANICAL SPECIFICATIONS
Dimensions: SC-200:15” X 12” X 2 1/4”
SC-1200: 18” X 16” X 2 ¼”
Weight per shot clock: 3 pounds (SC-200)
(approximate) 6 pounds (SC-1200)
ENVIRONMENTAL SPECIFICATIONS
Operating Temperature: +10 degrees C to +50 degrees C.
Storage Temperature: 0 degrees C to 80 degrees C.
Humidity: 0 to 95% non-condensing.

Copyright © 2017 Funtronix LLC. All rights reserved
9
Please visit our website for new products and accessories for your Funtronix Product:
www.funtronixonline.com