SL PROLIGHTING SL-1R100 User manual

'
J.
I
User Manual
lR mini beam moving head
•
Congratulatlons on purchasing thls 1R Beam
And thank you for extendlng your trust in our technology.
1
1
1
!·
,,

1
For reasons of safety and approval(CE) the personal reconstruction and/or modification of
this product is prohibited . Please observe that damage caused by mod i fications
performed manually to this device is not covered by the warranty.
This product leaves our works in a perfect condition . Please observe all notes in these
operating instructions to warrant this condition and the safe operation of the productl
Any damage caused as a result of the non-compliance with these operating instructions
leads to the expiration of any warranty claim. The manufacturer does not accept liability
for any damage to property or for personal injury resulting from the improper handling of
the product ,or non-observance of the operating instructions.
Store these operating instructions in asafe place for later reference and pass them to any
new holder when selling or lending or leaving this device in the hands of any other party.
1. Specification
Source
•Ught sourc:e: Yodn lamp
• Lamp llfe: 2.000 hours
• Lumlnous Flux: 3200LUMEN, 3680001ux@4m at 3.8°, 466LUXC8m at 3. 8°
• Control: Remote on/off vla DMX
• Ballast: swltchlng mode powersupply
Optlcal System
• Beam angle: 3.8°
X/Y
• Pan : 630° (2,5 sec) , or 540° (2sec) Tllt: 265° (1.8 ~r
• 16-blt resolutlon
• Auto reposlttonlng
Cofors
• 14+open, lnterchangeable, lndex able and bldlrecttonai ra ·. , , c ff ect
Gobos
• 14+open
Features
• DMX channels: 14 channels.
• Super fast, smooth and sllent movement
• Full range 0-100% dlmmer
•Various strobe
• Dlsplay fllp, X/Y reverse and so on
• Hlbematton when lost DMX f'or preset time
• Fan speed auto change accordlng to temperature
• Heat pipe f'or coollng
Power
2

• Max power consumptlon: 120W
• Power supply: Electronlc auto-ranglng
• Power In/out
• Input voltage range: 100-240V, 50-60Hz
Display
• 2.4inch super nlce LCD display wlth frtendly
Engllsh/ Chlnese menu
• Auto lock
• Fllp
Dlmenslon and Welght
• Flxture: 330X230X430 MM
• Paddng: 3S0X320X480 MM
• Net Welght : 9.5KG
• Gross Welght: 11.5KG
Rlgglng
• Mountlng polnts: 2 ¼-tum locks
• 1 x Omega brackets wlth ¼-tum qulck locks
• Safety rope
2. DMX Chart
Value
Function
1
0-255
Pan
0-100%
2
0-255
Pan fine
0-100%
3 0-255
Tilt
0-100%
4 0-255
Tilt fine
0-100%
5 0-255
Pan/Fine Speed
Fast-> Slow
Strobe/Shutter
252-255
Open
239-251
Random Strobe(Fast)
6
226-238
Random Strobe(Medium)
213-225
Random Strobe(Slow)
208-212
Open
108-207
Pulse: Slow •> Fast
104-107
Open
4-103
Strobe: Slow -> Fast
0-3
aose
7
0-255
Dlmmer 0-> 100%
3
-!
J
,,
.., .. .. ~·
,.\
í
... . _,""' ___ ,
---
-- -

ColorWheel
193-255 Rotation(CCW):Slow
-> Fast
191-192 stop
128-190 Rotation(CW): Fast-> Slow
124-127
BLUE + WHITEColor14
120-123
BLUE
116-119
ers 8000 + BLUE
111-115
CTB 8000
107-110
ero 190 + ere 8000
103-106
ero 190
99-102
ero 260 + ero 190
94-98
ero 260
90-93
CY AN + ero 260
86-89
CYAN
82-85
MAGENTA+ CYAN
77- 81
MAGENTA
8 73-76
YELLOW+ MAGENTA
69-72
YELLOW
64-68
PINK + YELLOW
60-63
PINK
56-59
LAVENDER + PI NK
52-55
LAVENDER
47-51
LIGHT GREEN+ LAV E r,·
43-46
LIGHT GREEN
39-42
GREEN+ LIGHT GR Ei. ,
35 - 38
GREEN
30-34
AQUAMARINE + GREEN
26-29
AQUAMARINE
22-25
ORANGE + AQUAMARINE
18-21
ORANGE
13-17
RED+ ORANGE
9-12
Red
5-8
White+red
0-4 White
4

Gabowt.
2SS
6080 14 SHA1CE. FASTSPEED
--
-•- ·•
251 6080 14 SHAlE. SlOW SPEED
-•• ·•
·--
185 6obo2
SHA.KE: FAST SPEED
-•• ·•·· •• · ••• ·•
1.81 Gobo2 SHAIE: SLOW SPEED
11()
FAST RO TA TlON(ODCXW!SE) }
......
···-·
135
StOW ROD\l10N (Cl.CXXWISE )
~134
~
:is
StOW ROTA~
........
·--·•
1
•
8;:
FAST ROTATIOH(ANTlClOOWISEl
.
•~"9
GobolS
- .:- - ~
Gobol4
4:- : -5-!
Gobol3
9 --
~:
GoboU
:
.
:= . :- :4 Gobol.1
1
.! :--$.~
GobolO
1
1 ~
--....:.t
Gobo9
35-39 Gobo8
30-34
Gobo7
~29
Gobo6
20-24
GoboS
1~19
Gobo4
15-19
Gobo3
10-14
Gobo2
5-9 Gobol
0-4 Open
10
0-255 Foms Neartofar
Prism
11 128-2.SS
Prism lnsert
0-127
Open
5

I
j
255
12
.. . .. .
193
191-192
190
... . ..
128
0-127
128-255
13
n-121
26-76
0-25
101-255
14
26-100
0-25
3. Notes on safety
1. Befare o,,.,..tlon
Prism Rotatlon
FAST ROTATION(CLOCKWISE)
.... ..
SLOW ROTATION(CLOCKWISE )
STOP
S LOW ROTATION(ANTICLOCKWISE)
......
FAST ROTATION(ANTICLOCKWISE)
Prism Posít lon
RESET
Al! reset
PAN/TILT RESET
EFFECTS RESET
Unused
·-··· -
Lamp
On
Off
Unused
1
ATIENTION:
DANGER OF LIFE I RISKOF FIRE 1
RISK OF SHORT CIRCUIT 1
Prior to the initial operation of this product, please do the followings
-Read these operating instructíons with great care ;
-Study and observe all ínstructions carefully;
-Ensure that everybody and anybody i nvolved in the installation , operation , transport and
storage of this product is suitably qual i fied ;
-Verify whether any VÍsible damage was caused during transport . lf the power cord .
hous i ng or the lig ht are damaged , do not operate the deVÍce; contact your specialized
dealer immediately .
2. Supp/y Voltage, Malns ConlandConnect/on to Malns
The handling of supply voltage , mains cords and connections to ma i ns calls for particula r
care considering the risk from a life-threatening electric shock,the risk of tire and the risk
of short cir cu its please observe the following notes in particular:
Products operating on supply voltage should be kept out of the reach of children .
Therefore ensure the permanent supeMsíon if children are in the immediate vicinity of the
6
'
J

product!
For commercial facilities the regulations on the prevention of accidents ofthe respective
trade association must be observed. The operation of this equipment at schools, training
facilities , and nobody or yourself-help workshops must be supervised responsibly by
trained personnel. Check the product regularty for any damage to the mains cord! Should
you discover any damage to the mains cord, do not operate or disconnect this productl
secure the product againstaccidental operation and contact your specialized dealer.
AtNays separate the product from mains by holding the mains plug by the handling
surface .Never disconnect by holding the line cord ! Be sure to connect the product
exclusively toAC110-127V/59-60Hz!
AtNays insure during installation, operation, transport an d when storing the product that
the mains cord is not exposed to possible mechar., .. ~3 ma ge , or damage caused by
humidity, fluids , heat or cold!
The products cable entry must not be exp os ed í(• :-' •;~ 4 S fro m pum Create the mains
connection once the product has been insta /le t1n · .,•n 9et the mains plug last !
The product must only be connected to a pr o·. ·. ~; tJJ hC supply grid . Connect
the mains cord to suitable outlets only !Use < i~
. r; -: 0:11 ::> l ia nce with
specifications only! Do notallow the mains ce ; -:.
,<Ct wi th other cords!
Ensure during installation ,operation, transpo r: · 1. • ._
.., :~L n:~:-:c of the cables are
freely exposed !
Never touch the mains cord ,mains plug and ou tlet w:L' 1wet or damp hands !
When not using the product, and preform to clean in g a! · ,...3y s dí sconnect the product from
mains! To do so, hold the mains plug by the handling surface and never pull the mains
cord!
Never connect the device to dímmer packer!
4. Housing
ATIENTION :
DANGER OF UFE ! RJSKOF FIRE !
RISK OF SHORT CIRCUIT !
Always i nsure during installation, operation, transport and when storing the product that
no shocks or other forces impact the housing 1
The housing must not touch onto any otherdevices orobjects during operation!
Easily flammable materials, e.g . decoration material and other surfaces and objects, must
maintain a minimum distance of 3m to the housing rwans must maintain a minimum
distance of 50cm to the housing! The device must be installed on a fireproof surface only
(no carpet)1 ANlays ensure a proper circulation of air.
Do not touch the housing during operation it will heat up .The housing is safe to touch
approx .. 5 minutes following the end ofoperationl
Thedevice must neverbe carried vía the projector anns . Use the caring handles only 1
Fluids must not enter the housing as thi s could reduce the protective insulation and may
7

trigger short circuits which may lead to fatal electro shocks !lf fluids have entered ,
disconnect the mains plug immediately and secura the product against un intentional
operation and contact yours specialized dealer! Damage caused as a re-suit offluids
entering the housing is exempt from warranty .
No metal parts or other items must enter the housing as this may reduce the protective
insulation or trigger short circuits which may lead to fatal electric shocks llf metal parts or
other items have entered , disconnect the mains plug immediately,secure the product
against unintentional operation and contact your spec i alized dealer!Damage caused by
metal parts orother items in the housing is exempt warrantable.
3. Operatlng Envlronment
AnENTION:
DANGER OF UFEI RISKOF FIRE 1
RISK OF SHORT CIRCUIT !
The product must be operated and stored in adry environment only!
Splash water ,rain , humidity, fog may reduce the protective insulation which may le ad to
fatal electric shocks !The limited value for relative humidity is 50% at 45 -C .A mínimum
distance of 1.5m to a fog machine must be observed ; fog saturation in the roo m mu st nct
reduce the visibility to below 10m .
The product must be operated ata temperature range of between -5 "C and 45 ·c. 01,:¡
Protect the product against direct exposure to sunlight or other heat, su ch a: fr •.) !'
radiatorsl lfthe product is taken from a cold environment into a warm environment 1, :" 1,1: l
only be taken into operation once it has reached ambient temperature, sm cc: ¡p¿
condensation created by the difference in temperature may destroy the devicel
Protect the product against dust! Dust may reduce the protective insulation, wh ích rn2y
cause fatal electric shocksl
The product must be operated at altitudes ranging between 20m below and 3000m a bove
sea level only!
The product must not be operated during thunder storms; risk of destruction from surge
voltages!
The product must be operated ata mínimum distance of 1. 5m to lit objects only!
5. lnstallation
~
ATIENTION :
RISK OF SHORT CIRCUIT !
This product can be operated suspended oras stand-alone system.
8

Should your lighting effect show any signs of damage, do not install the devicel In this
case , have your lighting effect repaired by your specialized dealer. The manufacturar does
not accept responsibility orliability far damage to
property or personal injury resulting from an improperty installationt
As a stand-alone system the device must be installed vertically on an absoluta planar, firm,
fireproof, shock and vibration-free surface. The installation of this lighting effect must be
carried out by trained and professional staffl The installation of this lighting must only be
carried out with the appropriate mataríais !
Toe suspended installation of this lighting effect necessitates a su i table suspension
systemt The líghting effect must nevar be fixed swinging freely in the room. No individuals
should li nger undemeath the lighting effect during suspended installation!
lt is a must to install this device with a second indepe nd <: i'~
1;
xt ure . Such second fixture
must guarantee in the event of failure of the main fixture that no assembly parts will fall
down. Use the fixture on the undersurface only .
The light effect unit must be attached via two cert ífie d hc ,.: .-l ,··,,.\ Gm eg a bracket to a
tie-bar system. Use the screw threads on the unde rs u rfñ . '.: ·1 ·
lt must be ensured that an expert inspects the m ec ha :: :,:..
prior to the ínitial operation and following ma jor r .: .,
operation. lt must be ensured that an expert inspe ::; r:; :
_. ., Jn t ins tallation
r. 1 ,he renewed
·J sa fe ty-relevant
installation at least once ayear. lt must be ensured t :-. 3, , , •- , ts the mechanical
i nstallation and the installation of relevance to s ~r ¿ :•· .M <rame work of an
acceptance test at least every fouryears.
The ínstallation fixture must be as such that it can withstai:c tu~ ,~ ~~ rí od of 60m i nutes 10
times the load capacity without harmful deformation.
1t is prohibited for any individual to unnecessarily stay or pass beneath the installatlon
during any type of assembly work .
The light effect unit must be secured by a safety arrester cable if fly-mounted . The cable
must withstand 12 times the weigh of the light effect unit Use arrester cables equipped
with quick closing links . The dropping distance must not exceed 20 cm. Defect arrestar
cables or arrestar cables that have already been exposed to stress must not be used.
6. Operation
[
ATIENTION :
RISK OF SHORT CIRCUIT 1
Controls
9

Link all DMX devices with a DMX-512 controller by using a standard,3-pin DMX cable.
connectthe output of the first devicewith the input of the second device and the output of
the second devicewith the input of the third device and so on.
Connectthe mains plug to an outlet.
operating the product for the first time may generatesmoke and odor, this is not a defect.
Avoid dis/connecting the product repeatedly and quickly from/with mainsl Always wait 15
minutes prior to the nextdis/connection!
The device starts not until a self-testing and starting time. lf the moving head is ready to
start, push and roll the function wheel. The LCD display shows the options.
7. Lamps
ATI'ENTION : --¡
DANGER OF LIFE ! RISKOF FU U: !
RISK OF SHORT CIRCUfT :
During operation, the lamps will reach temperaturas of up to 600 O C. To i!<:: :· :-., : ·r.a iamps
may cause serious bums! Objects coming into contact with the lamps du nr,~~ . ,,id shortly
afteroperation may catch fire!
Disconnect the product from mains prior to installing or befare changing a lam i:, ! Allow a
lampto cool forapprox.15minutes befare exchanging it!
Never touch a lamp with bare handsl lf damaged or deformad, a lamp must be
exchanged!
When exchanging the lamp be sure to use suitable lamps only. Lamps with greater
performance generate excessive heat for the product; risk of firel Damage resulting from
the use of an unsuitable lampisexempt from warranty!
Neverconnect the lighting effect to the mains priorwith opened housing.
B.Fuse
ATTENTION:
DANGER OF UFE ! RISKOF FIRE !
Rl8K OF SHORT CIRCUIT !
Disconnect the productfrom the mains prior befare changing a fuse.
Only replace the fuse by a fuse of same type and rating! An incorrect fuse could damage
of destructthe lighting effect.
Replace a fuse by levering the fuse holder coverwith an appropriate screwdriver. Remove
the old fuse and place the fuse lnslde the holder. Replace the fuse holderand insert it
Neverconnect the lighting effect to the mains prior With opened housing.
10

9, C/eaning
ATIENTION:
DANGER OF UFE ! RISKOF FIRE !
RISK OF SHORT CIRCUIT !
The product must be freed regularly from dust, other deposits and contamination as this
may reduce the protective insulation, which may lead to a fatal electric shock!
Before cleaning, always disconnect the product from mains!
This product should be cleaned with a moist cloth only; never use aggressive cleaning
agents, solvents or benzene for cleaning.
Ensure that the product is completely dry before operating it again after cleaning!
A1TENTION :
FRAOILEI
RISK OF SHORT CIRCUI 1!
To avoid damage caused during transport, wrap the product in i ts m ;~\:-: -:-l · .,. : :: ·, ··,g c 1, ly
and handle it with great care during transport!
11