Slam Specialties MC.1-SS User manual

SLAM SPECIALTIES
Control Systems
Model No. : MC.1-SS Made in USA
Thank you for purchasing the MC.1 Controller from Slam Specialties. This page includes installation instruc-
tions as well as contact information for technical support. If you have any questions about the operation of this
unit, please call 888-352-5225.
The MC.1 is a two part control system for air suspension vehicles consisting of a handheld control unit and the
accompanying receiver/driver module. Microprocessors and solid state drivers offer fast reliable response while
communicating with each other over a single wire, making the unit easy to install and flexible to move.
There are two multi-conductor cables in the receiver box. The 3-conductor is for power, ground and ignition; the
9-conductor is for hooking up your valves. Please follow these instructions for wiring your MC.1. NOTE: the Aux
wire is optional. The controller will funtion normally with or without the Aux wire connected. AUX function is activated
by a ground trigger. When activated, the four fill valve outputs are energized until the ground trigger is released off
of the Aux line.
Front Up
Rear Up
Front Driver Up
Front Driver Down
Front Passenger Up
Front Passenger Down
Rear Passenger Up
Rear Passenger Down
Front Down
All Up (Pancake)All Down (Pancake)
Rear Driver Up
Rear Driver Down
Handheld operation wired as g. 2
Rear Down
The MC.1 can be wired in multiple configurations depending on the desired orientation of the handheld (fig. 2 and
fig. 3). below is the valve wiring diagram for each configuration. Connect the power wire as per fig 1. for BOTH
configurations. g. 1
MC.1 Receiver
Power cable
Valve cable
Handheld Jack
AUX input
pg 1/3
fig. 2
fig. 3
Valve Wiring
Valve Wiring
Receiver Power Wiring
Red
Green
White
Purple
Brown
Blue
Yellow
Orange
Black
Orange
Yellow
Blue
Brown
Purple
White
Green
Red
Black
Front Driver Fill
Front Driver Dump
Front Passenger Fill
Front Passenger Dump
Rear Driver Fill
Rear Driver Dump
Rear Passenger Fill
Rear Passenger Dump
Valve Grounds (-)
Front Driver Fill
Front Driver Dump
Front Passenger Fill
Front Passenger Dump
Rear Driver Fill
Rear Driver Dump
Rear Passenger Fill
Rear Passenger Dump
Valve Grounds (-)
Red
Orange
Black
Black.1
Battery (+12v)
Ignition (+12v)
Ground
Aux input
10A
Fuse
Red
+12v
Orange
Black Ground
Ignition (+12)
Black.1
OFF ROAD/SHOW USE ONLY
Aux Input Wiring/function
Aux wiring is ground trigger. While (-)
signal is applied, the box will output to
all fill valves, until (-) signal is released

SLAM SPECIALTIES
Control Systems
Model No. : MC.1-SS Made in USA
Contents:
(1) Handheld Unit
(1) Receiver Unit
(9) Male Bullet Connectors
(1) 10A ATC fuse
(2) Self tapping screws
(1) 3/8” Grommets
Dimensional Data:
3.775”
1.45” 0.895”
1.95”
www.slamspecialties.com 1.888.352.5225
OFF-ROAD/SHOW USE ONLY
pg 2/3
.187”
Aux Operation
The Auxiliary function of the MC.1 is pre-programmed from the factory to
energize the fill valves when triggered with a ground/negative trigger. This is
only the case when the controller is configured as shown in Fig 2.
In the event the controller is installed in the configuration as shown in Fig 3,
press and hold both the fill and dump button (circled in Fig 2, or Fig 3) for three
seconds. The LED on the bottom of the controller will flash red/green to
indicate that the function has changed from fill to dump, or from dump to fill.
This change will remain stored in the controller until re-programmed by doing
this process again.
Check www.slamspecialties.com for more information

SLAM SPECIALTIES
Control Systems
Model No. : MC.1-SS Made in USA
Dimensional Data: *prints are actual size
OFF-ROAD/SHOW USE ONLY
www.slamspecialties.com 1.888.352.5225
pg 3/3
1.8” .395”
3.75”