Slant/Fin VICTORY II VHS Series User manual

IMPORTANT
READ A OF THE FO OWING
WARNINGS AND STATEMENTS
BEFORE READING THE
INSTA ATION INSTRUCTIONS
WARNING
LIQUE IED PETROLEUM (L.P.)
PROPANE GAS- IRED BOILERS
Installation location ONLY as permitted in paragraph
entitled "LIQUE IED PETROLEUM (L.P.) PROPANE
GAS- IRED BOILER LOCATION" on page 4 of this
instruction book.
The above warning does not apply to NATURA gas-
fired boilers.
The installation must conform to the requirements of
the authority having jurisdiction or, in the absence of
such requirements, to the National uel Gas Code,
ANSI Z223.1-latest edition. The installation must also
conform to the additional requirements in this Slant/ in
Instruction Book.
In addition where required by the authority having juris-
diction, the installation must conform to American
Society of Mechanical Engineers Safety Code for
Controls and Safety Devices for Automatically ired
Boilers, No. CSD-1.
WARNING
This boiler, gas piping and accessories must be
installed, connected, serviced and repaired by a
trained, experienced service technician, familiar with all
precautions required for gas-fired equipment and
licensed or otherwise qualified, in compliance with the
authority having jurisdiction.
WARNING
The venting system of this boiler is under positive pressure. Leakage from this
system can be hazardous and if not avoided can result in death or serious injury.
In addition to the recommendations within this manual and the User’s Information
Manual, the venting system, from the blower to the outdoor discharge, must be
carefully checked annually by aqualified service agency.
IMPORTANT
RADIANT FLOOR, LOW WATER TEMPERATURE, AND LARGE WATER VOLUME
systems require special piping arrangements. ee page 18.
This manual must be left
with owner and should be
hung on or adjacent to
the boiler for reference.
VICTORY VSP™
INSTALLATION AND OPERATING INSTRUCTIONS
Publication No. VSP-40 Part No. 455002 Printed in U.S.A.303
Heating Contractor
Address
Phone Number
Boiler Model Number
Boiler Serial Number
Installation Date
DIRECT-VENT SEA ED COMBUSTION BOI ERS
HOT WATER MODE S VSP-60 THROUGH VSP-180
GAS-FIRED CAST-IRON BOI ERS FOR NATURA AND .P. PROPANE GASES
TABLE OF CONTENTS
Dimensions, Rating and Orifice Sizes ........................................2
Identification of Parts ..................................................................3
Installation Requirements ...........................................................4
Venting Application .....................................................................5
Boiler Room Air Supply and Ventilation......................................5
lue gas Venting Requirements..................................................5
Vent Material ..............................................................................5
Air Intake Material ......................................................................6
lue and Air Intake Restrictions .................................................6
Non-Direct Vent Installation ........................................................8
Sidewall Venting, Non-Direct Vent ..............................................8
Vent Termination Location and Clearance..................................8
Non-Direct Vent Vertical Venting .................................................8
Direct Vent Installation ................................................................8
Sidewall Venting, Direct Vent ......................................................8
Vent/Air Intake Termination Installation.......................................8
Direct Vent, Venting and Air Intake through a Roof ..................13
Venting and Air Intake Regular Inspection ...............................15
Gas Piping ................................................................................15
Electrical Wiring ........................................................................15
Multi Zoning ..............................................................................18
Water Piping .............................................................................18
Wiring Diagram.........................................................................16
Operating Instructions...............................................................19
Gas Input Rate Adjustment ......................................................20
Boiler Control ............................................................................22
Sequence of Operation.............................................................21
Status of Indicator Lights (LED’s).............................................22
Safety Check ...........................................................................23
Care and Maintenance .............................................................24
General Troubleshooting Guide...........................................25-27

VICTORY VSP Models
2
NOTE: Height dimensions increase by 11⁄2" and depth increases to 281⁄2" when combustible floor kit is used.
Natural #49 50 50 50 51 51 51 52 52 52
Propane #57 58 59 59 60 60 61 62 63 63
VSP-60 60,000 3 111⁄8"173⁄8"
VSP-90 90,000 4 141⁄8"203⁄8"
VSP-120 120,000 5 171⁄8"233⁄8"
VSP-150 150,000 6 201⁄8"263⁄8"
VSP-180 180,000 7 231⁄8"293⁄8"
Boiler
Model
No. of
Sections
Input
Btuh AB
Gas
Type 2000 3000 4000 5000 6000 7000 8000 9000 10000
Orifice
Size for
Sea evel
Orifice Sizes for High Altitudes
Includes 4% Reduction for Each 1000 Feet
Elevation — Feet
Orifice sizes indicated for sea level above are factory installed in boiler unless otherwise specified by the local authority. Orifice
table is based on a higher heating value between 1000 Btuh and 1010 Btuh for Natural Gas (See page 20, if local higher heat-
ing value exceeds these numbers). See page 20, for burner input adjustment.
LEFT SIDELEFT SIDE FRONTFRONTRIGHT SIDERIGHT SIDE
(DOTTEDPIPING(DOTTEDPIPING
BYOTHERS)BYOTHERS)INSTALLMA NUALMA ININSTALLMA NUALMA IN
SHUTOFFVALVE5'ABOVESHUTOFFVALVE5'ABOVE
FLOOR WHENREQUIREDBYFLOOR WHENREQUIREDBY
LOCALCODELOCALCODE
PRESSURERELIEFPRESSURERELIEF
VALVEVALVE
1-1/2"FPT1-1/2"FPT
SUPPLYSUPPLY
3/4"3/4"
DRAINDRAIN
28-3/428-3/4
(SEENOTE)(SEENOTE)
25-1/825-1/8
(SEENOTE)(SEENOTE)
3/4"TOAIR3/4"TOAIR
ELIMINATINGELIMINATING
SYSTEMSYSTEM
30-1/230-1/2
(SEENOTE)(SEENOTE)
SEDIMENTSEDIMENT
TRAPTRAP
(REQUIRED)(REQUIRED)"A""A"
JACKETJACKET
"B""B"
3"DIA3"DIA
VENTVENT
CONNECTORCONNECTOR
PRESS/TEMPPRESS/TEMP
GAUGEGAUGE
JUNCTIONJUNCTION
BOXBOX
1-1/2"1-1/2"
RETURN TAPPING,RETURN TAPPING,
1-1/4"CIR.FLANGE1-1/4"CIR.FLANGE
VENTVENT
CONNECTORCONNECTOR
28-1/2"28-1/2"
(SEENOTE)(SEENOTE)
RATINGS AND DIMENSIONS
Figure 1. Dimensions data
Gas Orifice Size Victory VS boiler

VICTORY VSP Models 3
LOCATION AND IDENTIFICATION OF PARTS
Figure 2. Location and identification of parts
Base Assembly

VICTORY VSP Models
4
The installation must conform to the requirements of the
authority having jurisdiction or, in the absence of such
requirements, to the National uel Gas Code, ANSI Z223.1-
latest edition.
This installation must also conform to the additional require-
ments in this Slant/ in Instruction Book.
NATURA GAS-FIRED BOI ER OCATION
Provide a level, solid foundation for the boiler. Location
should be as near as possible to chimney or outside wall so
that the flue pipe from boiler is short and direct. (See Appen-
dix A for vent terminal location restrictions.) The location
should also be such that all boiler components are protected
from water (dripping, spraying, rain, etc.) during appliance
operation and service (circulator replacement, control
replacement, etc.).
WARNING
IQUEFIED PETRO EUM ( .P.) PROPANE GAS-FIRED
BOI ER OCATION
REQUIRES SPECIAL ATTENTION
Liquefied Petroleum (L.P.) propane gas is he vier th n ir.
Therefore, propane boilers, piping, valves should NOT be
installed in locations where propane leaking from defective
equipment and piping will "pool" in a basement or other
space below the leak.
A spark or flame from the boiler or other source may ignite
the accumulated propane gas causing an explosion or fire.
Provide a level, solid foundation for the boiler. Location
should be as near the chimney as possible so that the flue
pipe from boiler to chimney is short and direct.
The UNIFORM MECHANICA CODE may be in effect in
your geographic area.
The following precautions are cited by the 1994 UNI ORM
MECHANICAL CODE, section 304.6:
" PG Appliances. Liquefied petroleum gas-burning
appliances shall not be installed in a pit, basement or
similar location where heavier-than-air-gas might collect.
Appliances so fueled shall not be installed in an above-
grade under-floor space or basement unless such loca-
tion is provided with an approved means for removal of
unburned gas."
Consult Chapter 5 of the 1994 UNI ORM MECHANICAL
CODE for design criteria of the "approved" means for
removal of unburned gas.
BOI ER FOUNDATION
A. Provide a solid, level foundation, capable of supporting
the weight of the boiler filled with water, and extending at
least 2" past the jacket on all sides. See dimensions of
boilers, page 2.
B. or installation on non-combustible floors only*.
C. If boiler is to be located over buried conduit containing
electric wires or telephone cables, consult local codes or
the National Board of ire Underwriters for specific
requirements.
* Installation on combustible flooring allowed only with proper Com-
bustible loor Kit. Kit part number is printed on boiler rating plate.
In no case may the boiler be installed on carpeting.
MINIMUM C EARANCES FROM COMBUSTIB E
CONSTRUCTIONS
A. Minimum clearances to the exterior surfaces of the boiler
shall be as follows:
MINIMUM ALCOVE AND CLOSET CLEARANCE
or Combustible Recommended
Surface Construction for Service
ront 6" 18"
Rear 6" 18"
Left Side 6" 18"
Right Side 12" 24"
Top 12" 12"
lue Connector:
Enclosed — 6" 6"
Uninclosed — 2" 6"
B. Provide accessibility clearance of 24" on sides requiring
servicing and 18" on sides used for passage.
C. All minimum clearances shown above must be met. This
may result in increased values of some minimum clear-
ances in order to maintain the minimum clearances of
others.
D. Clearance from hot water pipes shall be 1 inch**.
** At points where hot water pipes emerge from a floor, wall or ceiling,
the clearance at the opening through the finished floor boards or wall
or ceiling boards may be not less than 1/2 inch. Each such opening
shall be covered with a plate of uncombustible material.
SAFETY
KEEP THE BOILER AREA CLEAR AND REE ROM
COMBUSTIBLE MATERIALS, GASOLINE AND OTHER
LAMMABLE VAPORS AND LIQUIDS.
**
**
**
12"
6"
6"
6"
2"
2"
12"
: 6" FOR ENCLOSED
VICTORY "VSPH" BOILER
MIN. CLEARANCES FOR
COMBUSTIBLE CONSTRUCTION
Figure 3. Victory “VSP” boiler min. clearances for
combustible construction.
INSTA ATION REQUIREMENTS

VENTING APP ICATION
VSP Series are sealed combustion type boilers, they maybe
installed and vented either as direct vent boiler which all air for
combustion is obtained directly from outside or as non-direct
vent boiler which air for combustion is taken from inside the
boiler room.
VSP boilers must be vented by proper 3" diameter. Stainless
Steal venting system (see “vent material” on this page) through
the roof or sidewall.
BOI ER ROOM AIR SUPP Y AND VENTI ATION
An ample supply of air is required for combustion and ventila-
tion. When buildings are insulated, caulked and weather-
stripped, now or later on, direct openings to outside may be
required and should be provided. If the boiler is not near an
outside wall, air may be ducted to it from outside wall openings.
Provisions for combustion and ventilation air must be made in
accordance with section 5.3, Air for Combustion and Ventila-
tion, of the National uel Gas Code, ANSI Z223.1-latest edi-
tion, or applicable provisions of the local building codes. The
following recommendation applies to buildings of energy-saving
construction, fully caulked and weatherstripped.
INSTALLATION IN ENCLOSED BOILER ROOM REQUIRES
TWO UNOBSTRUCTED OPENINGS OR PASSAGE O AIR
INTO THE BOILER ROOM:
A. NON-DIRECT VENT INSTA ATION
1. Air drawn horizontally from outdoors DIRECT Y
through an outside wall; one louvered opening near the
floor and one louvered opening near the ceiling, each open-
ing with a minimum REE air passage area of 1 square
inch per 4000 Btuh of total appliances’ input.
2. Air drawn horizontally through HORIZONTA DUCTS;
one opening near the floor and one opening near the ceil-
ing, each opening with a minimum REE air passage area
of 1 square inch per 2000 Btuh of total appliances’ input.
3. Air drawn VERTICA Y from outdoors; one opening at
the floor and one opening at the ceiling, each opening with
a minimum REE air passage area of 1 square inch per
4000 Btuh of total appliances’ input.
4. Air drawn from inside the building; one opening near
the floor and one opening near the ceiling, each opening
with a minimum REE air passage area of 1 square inch
per 1000 Btuh of total appliances’ input.
I BOILERS ARE INSTALLED ADJACENT TO OTHER UEL
BURNING EQUIPMENT, THE AREA O REE OPENINGS
MUST BE APPROPRIATELY INCREASED TO ACCOMMO-
DATE THE ADDITIONAL LOAD.
B. DIRECT VENT INSTA ATION
Adequate air supply should be provided to prevent overheating
of the boiler controls and boiler room. Openings for passage of
air into the boiler room for direct-vent installation must be at
least 1⁄2 of the openings required for the non-direct vent as men-
tioned above.
If additional non-direct vent appliances are installed in the same
space and adequate air openings are provided for them, there
are no additional air openings required for the VSP boiler.
or both direct and non-direct installation, the following must be
considered:
- Openings must never be reduced or closed. If doors or
windows are used for air supply, they must be locked open.
- Protect against closure of openings by snow and debris.
Inspect frequently.
- No mechanical draft exhaust or supply fans are to be
used in or near the boiler area.
- Boiler area must never be under negative pressure. The
flow of combustion and ventilating air to the boiler must
not be obstructed.
F UE GAS VENTING REQUIREMENTS
The Victory VSP series boiler is a high efficiency, mechanically
induced draft boiler and, therefore, requires different venting
arrangements than natural draft, lower efficiency boilers.
THE OLLOWING INSTRUCTIONS MUST BE CARE ULLY
READ AND OLLOWED IN ORDER TO AVOID ANY HAZ-
ARDOUS CONDITIONS DUE TO IMPROPER INSTALLATION
O THE AIR INTAKE AND LUE GAS VENTING SYSTEM.
The vent piping installation MUST be in accordance with these
instructions and with ANSI Z223.1-latest edition NATIONAL
UEL GAS CODE, Part 7, Venting of Equipment. Other local
codes may also apply and must be followed. Where there is a
conflict between these requirements, the more stringent case
shall apply.
The use of a vent damper is NOT permitted on this boiler series.
VENT MATERIA
The vent system for direct or non-direct vent installation must be
UL listed single wall 3” diameter AL29-4C* stainless steel materi-
al. The following manufacturers’ systems are approved for use
within a specified minimum and maximum equivalent vent length
for each model. Proper adapter must be used as a connector
between Victory VSP boilers flue collar and venting system as
shown below:
VICTORY VSP Models 5
*AL29-4C is registered Tr dem rk of Allegheny Ludlum Corp
He t-F b P rt Numbers for v rious items of vent system re listed in
Sl nt/Fin P rt List, Public tion No. VSP-10PL
Manufacturer Type/System Adapter art Sealant
No.
Heat- ab. Inc. Saf-T Vent Not Required RTV 106 or Dow
Corning 732
Heat- ab. Inc. Saf-T Vent Not Required Not Required
EZ Seal
ProTech asNSeal SA-SLB-3 Not Required
System, Inc.
lex-L StaR-34 SRA SA3 GE-1S806
International, Inc.
Z- lex, Inc. Z-Vent O2SVSSLA2 GE, RTV 106

When joining the various components of the above listed
vent systems, the manufacturers’ instructions should be
closely followed to insure proper sealing. Use sealant speci-
fied by vent system manufacturer for sealing of pipe and fit-
tings. See igure 4 for proper application of vent pipe sealing
for Saf-T vent system by Heat- ab, Inc. All vent connections
must be liquid and pressure tight. lue vent system CANNOT
be cut to length. Consult manufacturer’s instructions. or Heat-
ab system, use slip joint connector to adjust pipe lengths
dimensions.DO NOT use plastic or galvanized flue pipe.
AIR INTAKE PIPE MATERIA
3” PVC Schedule 40 or galvanized steel materials are rec-
ommended.
All joints must be sealed using appropriate sealants.
F UE AND AIR INTAKE RESTRICTIONS
1. Maximum allowed equivalent flue and air intake length for
different flue systems at different altitudes are given in the
tables on page 7.
2. Equivalent of flue or air intake length is sum of the
straight pipe lengths and equivalent length of elbows as
shown in the table on this page.
3. The vent termination is in addition to the allowed equiva-
lent lengths.
4. Minimum flue length is 2 feet.
5. lue length restriction is for both direct and non-direct
vent installations.
EXAMPLE: Boiler model VSP-180 is to be installed at sea
level. The combustion air is provided by air intake piping
directly to the boiler (direct-vent installation). lue piping
includes 2 elbows and using Heat- ab system. Air intake is
PVC and includes 3 elbows.
Maximum straight flue length would be 30-2x3=24 feet.
Maximum straight air intake pipe would be 40-3x5=25 feet.
If the air for combustion were taken from the boiler room
(non-direct vent installation), still the maximum straight flue
length would be 24 feet.
6. All Victory VSP boilers are equipped with a built-in
condensation drain and trap. The trap loop must be
filled with water. DO NOT operate the boiler without
filling the trap with water to prevent flue gas discharge
into space. The drain should extend to a floor drain or
to a container which may require emptying periodically.
7. The horizontal vent pipe must be sloped upward from
the boiler at a pitch of at least 1⁄4" per 1 foot of run, so
that the condensate from the vent system runs to the
drain trap.
8. The horizontal vent pipes must be supported with pipe
straps at intervals no greater than indicated by vent
pipe manufacturer’s instructions. The vertical portion
vent pipe also must be supported per manufacturer’s
instructions. Support air intake piping in the same
manner as the vent pipes.
9. Minimum clearances of vent pipes from combustible
constructions must be maintained (see Page 4). Main-
tain minimum 1" clearance between vent pipes and
PVC air intake pipes.
10. Common venting with other appliances or another VSP
boiler is not allowed.
11. DO NOT install a vent damper or similar devices in
vent system or on the boiler.
12. Do not insulate venting system.
VICTORY VSP Models
6
Figure: 4 Vent Sealing Instructions
(Consult vent manufacturer’s instructions.)
Heat- ab, Inc. Saf-T Standard 3
elbow
Heat- ab, Inc. Saf-T, tight radius elbow 6
ProTech System, Inc. asNseal 6
lex-L International, Inc. StaR-34 6
Z- lex, Inc. Z-Vent 6
N/A PVC, Schedule 40 5
N/A Galvanized steel 6
Manufacturer Type/System Equivalent
Length (Feet)
Equivalent Length of Various 90-Degree Elbows

VICTORY VSP Models 7
Maximum allowed flue and air intake equivalent length (Feet)
for
Heat-Fab Saf-T vent system (Including EZ-Seal)
Boiler Model
Number Piping
0 - 5,000 t.
Elevation
VSP-60 lue 40 40 40
Air Intake 40 40 40
VSP-90 lue 40 40 35
Air Intake 40 40 40
VSP-120 lue 40 35 30
Air Intake 40 40 40
VSP-150 lue 35 30 25
Air Intake 40 40 35
VSP-180 lue 33 28 23
Air Intake 40 35 30
5,000 - 7,500 t.
Elevation
7,500 - 10,000 t.
Elevation
Maximum allowed flue and air intake equivalent length (Feet)
for
Z-Flex Z-Vent and Flex- StaR-34 vent systems
Boiler Model
Number Piping
0 - 5,000 t.
Elevation
VSP-60 lue 35 35 35
Air Intake 40 40 40
VSP-90 lue 35 35 30
Air Intake 40 40 40
VSP-120 lue 35 30 25
Air Intake 40 40 40
VSP-150 lue 30 25 20
Air Intake 40 40 35
VSP-180 lue 28 23 18
Air Intake 40 35 30
5,000 - 7,500 t.
Elevation
7,500 - 10,000 t.
Elevation
Maximum allowed flue and air intake equivalent length (Feet)
for
ProTech FasNSeal vent systems
Boiler Model
Number Piping
0 - 5,000 t.
Elevation
VSP-60 lue 30 30 30
Air Intake 40 40 40
VSP-90 lue 30 30 25
Air Intake 40 40 40
VSP-120 lue 30 25 20
Air Intake 40 40 40
VSP-150 lue 25 20 15
Air Intake 40 40 35
VSP-180 lue 23 18 15
Air Intake 40 35 30
5,000 - 7,500 t.
Elevation
7,500 - 10,000 t.
Elevation

VICTORY VSP Models
8
VENTING INSTA ATION
ollow the vent material manufacturer’s instructions in con-
junction with these instructions for venting system installa-
tion.
I. Non-Direct Vent Installation
The air for combustion is taken from the ambient air sur-
rounding the boiler; therefore, ample supply of air is required
for combustion and ventilation (see page 5.)
DO NOT use this installation method if the surrounding of the
boiler is contaminated. The harmful corrosive contamination
may be from the chlorine-type detergents, cleaners, bleach-
es, and fabric softeners used in laundry or chlorine-based
swimming pool chemicals.
A. SIDEWA VENTING - NON-DIRECT VENT
igures 5 and 6 show typical horizontal sidewall venting. or
combustible wall passage of vent piping, a UL listed thimble
must be used, providing the wall thickness from 3" minimum
up to 12" maximum. The vent piping must terminate with a
screened tee or elbow termination facing down.
CAUTION: lue gasses existing from the vent terminal will
condense. Building materials in the area of the vent terminal
should be protected from discoloration and degradation.
VENT TERMINATION LOCATION AND CLEARANCES
1. The venting system shall terminate at least 3 feet above
any forced air inlet located within 10 feet.
2. The venting system shall terminate at least 4 feet below,
4 feet horizontally from, or 1 foot above any door, window
or gravity air inlet into any building. The bottom of the vent
terminal or air intake terminal shall be at least 12 inches
above grade or the normal snow level whichever is
greater.
3. Through the wall vents shall not terminate over public
walkways or over areas where condensate or vapor could
create a nuisance or hazard or could be detrimental to
the operation of regulators, relief valves or other equip-
ment. Minimum clearance of 4 feet horizontal distance is
maintained, from electric meters, gas meters, regulators
and relief equipment.
4. Vent termination must not be located in any confined
space (i.e. window wells, alcoves, narrow alleys) or under
any overhang or deck. Vent termination should not allow
flue gas discharge towards neighbor’s windows or where
personal injury or property damages can occur.
B. NON-DIRECT VENT - VERTICA VENTING
igure 7 shows typical venting through the roof. The vent
pipe must pass through the ceiling, floor and the roof verti-
cally through a 7" minimum diameter cutout. A fire stop is
required for each ceiling and floor penetration. or roof pas-
sage, an appropriate UL listed roof flashing must be used.
An existing chimney (see igure 8) may be used as a chase
for vertical venting. Other appliances CANNOT be vented
into the same chimney or vent pipe with in the chimney.
The vertical vent piping must terminate with a screened tee,
combination of 45˚ elbow and a 90˚ screened elbow termina-
tion or a rain cap termination.
II. Direct Vent Installation
Air intake piping from outside to the boiler air intake collar
provides the air for combustion. The boiler surrounding may
be contaminated with chlorine-based products such as laun-
dry detergents.
A. SIDEWA DIRECT VENTING
igures 9 and 10 show typical sidewall direct venting.
Slant/ in vent/air intake termination MUST be used for this
method of installation.
CAUTION: lue gasses existing from the vent terminal will
condense. Building materials in the area of the terminal
should be protected from discoloration and degradation. See
page 8 for vent termination location and required clearances.
VENT/AIR INTAKE TERMINATION INSTALLATION
1. Termination must be installed vertically with vent pipe
on the top.
2. Refer to igure 11 for installation details.
3. Wall thickness should be 3" to 12" thick
4. Maintain clearances for termination given on page 8.
5. Cut a rectangular opening with following dimensions in
the wall.
Height: 91⁄4" to 10"
Width: 71⁄4" to 8"
6. rom outside of the wall, install outside termination
plate using 4 screws.
7. or combustible wall a 4" galvanized pipe must be
used as a wall thimble.
The length of the 4" galvanized pipe should be
approximately 1" shorter than the wall thickness.
8. rom inside the building, fit galvanized pipe over 4"
collar of the outside plate.
9. rom inside, fit 3" diameter air intake pipe over 3"
collar located on the air box of the outside plate.
(text continued p.13)

VICTORY VSP Models 9
6IN. MIN.
9IN. MAX.
OUTSIDE V E NT TE RMI NATION
ELBOWWITHSCREEN
A U/L LISTEDWA L L T HIMBLE
MUST BE USEDON COMBUSTIBLE
WALLS. S/F P/N 440695
(ADJUSTAB LE 5IN. TO 8IN.)
MAYBE USED. ABOV E T HIMBLE
MUST BE USEDWITHHEAT-FAB
SLIP JOINT CONNECTOR
12"MIN
SNOWLINE
(SEE DEFINITION)
OUTSIDE
WALL
SLOPE UP 1/4 IN.
PER FOOT MIN.
FROM BOILER T O
V E N T T E R M I N AT I O N
STANDARD90˚
ELBOW
BUILT-IN
CONDENSATION
DRAIN &TRAP
3IN. DIA.
S.S. FLUE
PIPE (SEE
PAGE 5)
STAN DARD90˚ELBOW
OR
TIGHT RADIUS 90˚ELBOW
TO DRAIN OR
CONTAINER
FILL TRAP
WITHWATER
AIR INTAKE
(DO NOT BLOCK)
VSP BOILER
VICTORY VSP MODELS NON - DIRECT VENT, SIDEWALL VENTING
All joints must be liquid and pressure tight. Use U/L listed single wall 3" dia.
AL29-4C S.S.*. venting materials (See page 5).
Definition of Snow Line: Knowledge of local conditions will reveal the maximum height that repeated snowfalls accumulate to.
The height should be used as the SNOW LINE.
*AL 29-4C IS A REGISTERED TRADEMARK OF ALLEGHENY LUDLUM CORP.
Figure 5. on-direct vent, side wall venting.
Figure 6. on-direct vent, side wall venting.
SLOPE UP 1/4 IN.
PER FOOT MIN.
FROM BOILER TO
V E N T T E R M I N AT I O N
2FT. MIN.
6IN. MIN.
9IN. MAX.
OUTSIDE V ENT T ERM IN ATION
ELBOWWITHSCREEN
BUILT-IN
CONDENSATION
DRAIN &TRAP
FILL TRAP
WITHWATER
AIR INTAKE
(DO NOT BLOCK)
VSP BOILER
TO DRAIN OR
CONTAI NE R
3IN. DIA.
S.S. FLUE
PIPE (SEE
PAGE 5)
A WA L L T HIMBLE MUST
BE USEDON COMBUSTIBLE
WALLS. S/F P/N 440695
(ADJUSTABLE 5IN. TO 8IN.)
MAYBE USED. ABOV E T HIMBLE
MUST BE USEDWITHHEAT-FA B
SLIP JOINT CONNECTOR
12"MIN
SNOWLINE
(SEE DEFINITION)
OUTSIDE WALL

VICTORY VSP Models
10
FIRESTOP ANDFIRESTOP AND
SUPPORTSUPPORT
VENT TERMINATIONVENT TERMINATION
TEEWITHSCREENTEEWITHSCREEN
FLASHINGANDFLASHINGAND
STORMCOLLARSTORMCOLLAR
FIRESTOP ANDFIRESTOP AND
SUPPORTSUPPORT
1FTMIN.1FTMIN.
ALTERNATEVERTICALTERMINATIONALTERNATEVERTICALTERMINATION
S.
SLOPEUP1/4IN.SLOPEUP1/4IN.
PER FOOTMIN.PER FOOTMIN.
6"MIN6"MIN
TO DRAIN ORTO DRAIN OR
CONTAINERCONTAINER
4545˚˚ELBOWELBOW
9090˚˚TERMINATIONTERMINATION
ELBOWWITHSCREENELBOWWITHSCREEN
3IN.DIA.3IN.DIA.
S.S.VENTINGMATERIALS.S.VENTINGMATERIAL
3IN.DIA.3IN.DIA.
S.S.VENTINGMATERIALS.S.VENTINGMATERIAL
10FT.MIN10FT.MIN
RAIN CAP TERMINATION MAY BE USEDRAIN CAP TERMINATION MAY BE USED
VSPBOILERVSPBOILER
AIR INTAKEAIR INTAKE
(DO NOTBLOCK)(DO NOTBLOCK)
FILL TRAPFILL TRAP
WITHWATERWITHWATER
BUILT-INBUILT-IN
CONDENSATIONCONDENSATION
DRAIN&TRAPDRAIN&TRAP
VICTORY VSP MODELS- NON- DIRECT VENT, VENTING THROUGH A ROOF
All joints must be liquid and pressure tight. Use U/L listed single wall 3" dia.
AL29-4C* S.S. venting materials (See page 5).
Figure 7. Victory VSP models-non-direct vent, venting through the roof
*AL 29-4C IS A REGISTERED TRADEMARK OF ALLEGHENY LUDLUM CORP.

VICTORY VSP Models 11
RAIN CAP TERMINATION MAY BE USEDRAIN CAP TERMINATION MAY BE USED
SEAL CHIMNEY OPENINGSEAL CHIMNEY OPENING
WITH MORTARORCOVERPLATEWITH MORTARORCOVERPLATE
CHIMNEYCHIMNEY
TOP PLATETOP PLATE
VENTVENT
TERMINATIONTERMINATION
TEEWITH SCREENTEEWITH SCREEN
1FTMIN.1FTMIN.
ALTERNATEVERTICALTERMINATIONALTERNATEVERTICALTERMINATION
SLOPEUP1/4 IN.SLOPEUP1/4 IN.
PERFOOTMIN.PERFOOTMIN.
TO DRAIN ORTO DRAIN OR
CONTAINERCONTAINER
4545˚˚ELBOWELBOW
9090˚˚TERMINATIONTERMINATION
ELBOWWITH SCREENELBOWWITH SCREEN
VSPBOILERVSPBOILER
DRAIN&TRAPDRAIN&TRAP
CONDENSATIONCONDENSATION
BUILT-INBUILT-IN
AIRINTAKEAIRINTAKE
(DO NOTBLOCK)(DO NOTBLOCK)
WITH WATERWITH WATER
FILLTRAPFILLTRAP
3IN.DIA.3IN.DIA.
S.S.VENTINGS.S.VENTING
MA TERIALMA TERIAL
3IN.DIA.3IN.DIA.
S.S.VENTINGS.S.VENTING
MA TERIALMA TERIAL
10FT.MIN.10FT.MIN.
VICTORY VSP MODELS- NON - DIRECT VENT, UTILIZING AN EXISTING
CHIMNEY AS A CHASE
All joints must be liquid and pressure tight. Use U/L listed single wall 3" dia.
AL29-4C* S.S. venting materials (See page 5).
Figure 8. Victory VSP models-non-direct vent, utilizing an existing chimney as a chase
*AL 29-4C IS A REGISTERED TRADEMARK OF ALLEGHENY LUDLUM CORP.

VICTORY VSP Models
12
VICTORY VSP MODELS - DIRECT VENT, SIDEWALL VENTING
All joints must be liquid and pressure tight. Use U/L listed single wall 3" dia.
AL29-4C* S.S. venting materials (See page 5).
TO DRAIN ORTO DRAIN OR
CONTAINERCONTAINER
SLOPEUP1/4IN.SLOPEUP1/4IN.
PERFOOT MIN.PERFOOT MIN.
FROMBOILER TOFROMBOILER TO
VENT TERMINATIONVENT TERMINATION
SNOWLINESNOWLINE
(SEE DEFINITION)(SEE DEFINITION)
STRAIGHTSCREENEDSTRAIGHTSCREENED
VENT TERMINATIONVENT TERMINATION
FILL TRAPFILL TRAP
WITHWATERWITHWATER
BULT-INBULT-IN
COND ENSATIONCOND ENSATION
DRAIN&TRAPDRAIN&TRAP
HEAT-FABHEAT-FAB
18"SLIPJOINT18"SLIPJOINT
CONNECTORCONNECTOR
12"MIN12"MIN
VSPBOILERVSPBOILER
SLANT/FINSLANT/FIN
VENT/AIR INTAKEVENT/AIR INTAKE
TERMINATIONUNITTERMINATIONUNIT
3-12"THICK3-12"THICK
WALLWALL
AIR INTAKEAIR INTAKE
PIPE-3"I.D.PIPE-3"I.D.
GALVANIZEDGALVANIZED
STEELORPVCSTEELORPVC
FLUEPIEFLUEPIE
3"DIA3"DIA
S.S.(SEEPAGE5)S.S.(SEEPAGE5)
OUTSIDEOUTSIDE
WALLWALL
2FT.MIN.2FT.MIN.
AIR INTAKEAIR INTAKELOUVERSLOUVERS
SLOPEUP1/4IN.SLOPEUP1/4IN.
PERFOOT MIN.PERFOOT MIN.
FROMBOILER TOFROMBOILER TO
VENT TERMINATIONVENT TERMINATION
SNOWLINESNOWLINE
(SEE DEFINITION)(SEE DEFINITION)
TO DRAIN ORTO DRAIN OR
CONTAINERCONTAINER
BULT-INBULT-IN
COND ENSATIONCOND ENSATION
DRAIN&TRAPDRAIN&TRAP
FILL TRAPFILL TRAP
WITHWATERWITHWATER
FLUEPIPEFLUEPIPE
3"DIA.3"DIA.
S.S.(SEEPAGE5)S.S.(SEEPAGE5)
VSPBOILERVSPBOILER
AIR INTAKEAIR INTAKE
PIPE-3"I.D.PIPE-3"I.D.
GALVANIZEDGALVANIZED
STEELORPVCSTEELORPVC
HEAT-FABHEAT-FAB
18"SLIPJOINT18"SLIPJOINT
CONNECTORCONNECTOR
12"MIN12"MIN
OUTSIDEOUTSIDE
WALLWALL
9090˚˚ELBOWELBOW
3-12"THICK3-12"THICK
WALLWALL
SLANT/FINSLANT/FIN
VENT/AIR INTAKEVENT/AIR INTAKE
TERMINATIONUNITTERMINATIONUNIT
AIR INTAKEAIR INTAKELOUVERSLOUVERS
STRAIGHTSCREENEDSTRAIGHTSCREENED
VENT TERMINATIONVENT TERMINATION
Figure 9. Direct vent, sidewall venting illustration; with straight horizontal vent.
*AL 29-4C IS A REGISTERED TRADEMARK OF ALLEGHENY LUDLUM CORP.
Figure 10. Direct vent, sidewall venting illustration; horizontal vent using elbows.
** Definition of Snow Line: Knowledge of local conditions will reveal the maximum height that repeated snowfalls accumulate to.
The height should be used as the SNOW LINE.
**

VICTORY VSP Models 13
WALL
3" PVC OR
GALV.PIPE
FOR AIRINTAKE
3"AL294C
S.S.VENT PIPE
(SLIPJOINT CONNECTOR)
4"GALVANIZED
PIPE(WALL THIMBLE
FOR COMBUSTIBLE
WALLSONLY)
WALL
(3"-12"THICK)
SCREW
FLUEGASES
OUTSIDE
TERMINATION
PLATE
DO NOT
SEALHERE
DO NOT
SEALHERE
STRAIGHT
SCREENED
TERMINATION
STRAIGHT
SCREENED
TERMINATION
OUTSIDE
TERMINATION
PLATE
INSIDE
TERMINATION
PLATE
SCREW
4"GALVANIZED
PIPE
SEALHERE
INSIDETERMINATION
PLATE
COMBUSTIONAIR
Figure 11. Vent/Air Intake Termination
10. rom inside, install inside termination plate using 4
screws. Make sure the 4" collar on the plate, penetrate-
ed into the galvanized pipe.
11. Assemble and seal straight screened termination to
the slip joint connector.
12. rom outside of the building, insert vent pipe (slip joint
connector and termination assembly) through the 3"
holes of the outside and inside termination plate.
13. rom outside of the building seal outside termination
plate to building.
14. rom inside, proceed with air intake and vent pipe
installation. ollow vent manufacturer’s instructions and
restrictions mentioned on page 6 of this manual. DO
NOT exceed the maximum allowed equivalent lengths
given in tables on page 7.
When joining various components of the vent system and air
intake piping, proper sealant must be used (see page 6).
Install horizontal vent pipe with seams on the top. Connect
and seal air intake piping to air intake collar of the boiler.
Adjust the air pipe support to hold air intake pipe securely
(see igure 2).
B. DIRECT VENT - VENTING AND AIR INTAKE
THROUGH A ROOF
igure 12 shows typical vertical venting. The vent pipe must
pass through the ceiling, floor and the roof vertically through a
7" minimum diameter cutout. A fire stop is required for each
ceiling and floor penetration. or roof passage an appropriate
UL listed roof flashing must be used.
The vertical vent piping must terminate with a screened
straight termination.
The air intake terminal should be a screened 180˚ elbow fac-
ing down. The air intake opening must be at least 1 foot below
the vent opening.
ollow vent manufacturer’s instructions and restrictions men-
tioned on page 6 of this manual.
DO NOT exceed the maximum allowed equivalent length given
in tables on page 7. When joining various components of the
vent system and air intake piping, proper sealant must be
used (see page 6).
Install horizontal vent pipe with seams on the top. Connect
and seal air intake piping to air intake collar of the boiler.
Adjust the air pipe support to hold air intake pipe securely
(See igure 2).

VICTORY VSP Models
14
FIRESTOP AND
SUPPORT
FIRESTOP AND
SUPPORT
ALLJOINTS INVENT SYSTEMMUSTBELIQUID AND PRESSURE TIGHT.USEU/LLISTED
SINGLEWALL3" DIA.AL29-4C S.S.VENTINGMATERIALS(SEE PAGE5).
AL29-4CIS A REGISTERED TRADEMARKOF ALLEGHENYLUDLUMCORP.
SLOPEUP1/4IN.
PER FOOTMIN.
VICTORY VSP MODELS
TO DRAIN OR
CONTAINER
*
DIRECT VENT,VENTING AND AIR INTAKE THROUGH AROOF
3IN.DIA.
S.S.VENTINGMATERIAL
(SEE PAGE5)
3IN.DIA.
S.S.VENTING
MATERIAL
VSPBOILER
FILL TRAP
WITHWATER
BUILT-IN
CONDENSATION
DRAIN&TRAP
STRAIGHT TERMINATION
WITHSCREEN
SNOW
LINE
2"MIN
PIPE
SUPPORT
1FT.MIN.
AIR INTAKE
180˚ ELBOW
WITHSCREEN
FLASHINGAND
STORMCOLLAR
3" PVCOR
GALVANIZED
AIR INTAKE
PIPE
1FT.MIN.
10FT.MIN.
(FOR PVCAIR
INTAKE PIPE)
6"MIN.
Figure 12. Direct vent, venting and air intake through a roof.
VICTORY VSP MODELS
DIRECT VENT, VENTING AND AIR INTAKE THROUGH A ROOF
All joints in vent system must be liquid and pressure tight. Use U/L listed
single wall 3” dia. AL29-4C S.S. venting materials (See page 5).

VICTORY VSP Models 15
VENTING AND AIR INTAKE SYSTEM REGULAR
INS ECTION
A. Inspect the system regularly for condensation, corrosion
and/or physical damage. A qualified professional should ser-
vice the boiler annually and include such an inspection at that
time. The homeowner should look over the system monthly for
damage, water stains, any signs of rust, other corrosions or
separation of the vent and air intake piping (if direct-vent).
B. Should an inspection turn up signs of condensation, corrosion
or damage, the boiler should be shut down immediately and
the condition should be corrected by a qualified professional.
C. All Victory VSP boilers are equipped with a built-in condensa-
tion drain and trap. The trap loop must be filled with water. DO
NOT operate the boiler without filling the trap with water to
prevent flue gas discharge into space. Periodic inspection
should be made of this assembly for deterioration of the tub-
ing and to insure that the trap is not plugged. If it is plugged or
appears to have excessive sediment in it, it should be
removed from the drain assembly, straightened out to clear
the obstruction, reformed, filled with water and reinstalled as
before.
GAS PIPING
A. Local installation codes apply. The pipe joint compound
used on threads must be resistant to the action of liquefied
petroleum gases.
B. The gas supply line to the boiler should run directly from the
meter for natural gas or from the fuel tank for L.P. propane
gas. See page 2 for location of union and manual main
shut-off valve that may be specified locally.
Selecting pipe size for natural gas:
1. Measure or estimate the length of piping from the meter
to the installation site.
2. Consult gas supplier for heating value of gas (Btu/cu. ft.).
3. Divide boiler rated input by heating value to find gas flow
in piping (cu. ft. per hour).
4. Use table below to select proper pipe size.
EXAMPLE: Boiler model VSP-150 is to be installed. Distance
from gas meter to the boilers is 30ft. Heating value of natural
gas is 1020 Btu/cu. t. Select proper pipe size.
Gas flow = 150,000 Btu/hour = 147 cu. ft. per hour
1020 Btu/cu. ft.
At 30 ft. length of pipe, match required capacity from table on
this page (choose higher capacity, in this case is 152 cu. ft. per
hour). Required pipe size is 3⁄4".
Improper gas pipe sizing will result in pilot flame outages, insuf-
ficient heat and other installation difficulties. or more informa-
tion and also if other appliances are to be attached to the pip-
ing system, see Appendix C of National uel Gas Code ANSI
Z223.1-latest edition.
C. The boiler and its gas connection must be leak tested
before placing the boiler in operation. Use liquid soap solu-
tion for all gas leak testing. DO NOT use open flame. This
boiler and its individual shutoff valve must be disconnected
from the gas supply piping system during any pressure test-
ing of that system at test pressures in excess of 1⁄2PSIG.
This boiler must be isolated from the gas supply piping sys-
tem by closing its individual manual shutoff valve during any
pressure testing of the gas supply piping system at test
pressures equal to or less than 1⁄2PSIG.
D. All gas piping used should be inspected thoroughly for
cleanliness before makeup. A sediment trap must be provid-
ed, as illustrated on page 2.
E. The minimum and maximum gas supply pressure (at the
inlet of gas valve) are shown on the boiler rating plate for
the type of gas used. Gas supply pressure should never be
less than minimum or more than maximum pressure when
the boiler or any other appliance is turned on or off.
E ECTRICA WIRING
DANGER: Before wiring always turn off electric power supply
otherwise, shock or death can result.
1. Power Supply
A separately fused circuit is recommended. Use standard
15 Amp. fuse or breaker and 14 gage conductors in BX
cable or conduit.
Provide disconnect means and overload protection as
required. See boiler wiring diagram ( igure 13a) boiler con-
trol ( igure13b) and ladder diagram ( igure 13c).
Boiler must be electrically grounded in accordance with the
requirements of the authority having jurisdiction, or, in the
absence of such requirements, with the National Electrical
Code, ANSI/N PA 70-latest edition.
Length
of pipe
in eet 1/2 3/411
1/411/2
Gas low In piping -- cu. ft. per hr.
Iron Pipe Size (IPS) — inches
10 132 278 520 1050 1600
20 92 190 350 730 1100
30 73 152 285 590 890
40 63 130 245 500 760
50 56 115 215 440 670
60 50 105 195 400 610
70 46 96 180 370 560
80 43 90 170 350 530
90 40 84 160 320 490
100 38 79 150 305 460
At pressure drop of 0.3 in. water, specific gravity = 0.6.

VICTORY VSP Models
16
PILOTPILO T
BURNERBURNER
MODEL UT-1107MODEL UT-1107
P5P5 P4P4 P1P1 P6P6
P2P2
P3P3
INTEGRATED BOILER CONTROLINTEGRATED BOILER CONTROL
P6P6
THERMOSTATTHERMOSTAT
K4K4
MVMV
MV/PVMV/PV
PVPV
NEUTRALNEUTRAL
HOTHOT
MM
12 0 V /60H z120 V /60H z
120VAC120VAC
24VAC24VAC
K5K5
K1K1
MM
CIRCULATORCIRCULATO R
BLOWERBLOWER
HIGHHIGH
LIMITLIMIT
PRESSUREPRESSURE
SWITCHSWITCH
ROLL-OUTROLL-OUT
SWITCHSWITCH
L1L1
11
L2L2
GNDGND
P6P6
44
P5P5
P4P4
11
55
P4P4
11
P5P5
P4P4
22
33
DISCONNECTDISCONNECT
SWITCHSWITCH
P1P1
33
P1P1
11
P2P2
22
P2P2 11
P6P6
33
P6P6
22
P3P3
99
CHASSISCHASSIS
GNDGND
P3P3
77P3P3
44
P3P3
66
P3P3
33
P3P3
11
P3P3
55
P3P3
22
NOTE:NOTE: PXPX
INDICATES CONNECTOR'S TERMINAL ON BOILER CONTROLINDICATES CONNECTOR'S TERMINAL ON BOILER CONTROL
K3K3
P3P3
88
Figure 13b. Boiler control Figure 13c. Ladder wiring diagram
PRESSURE
SWITCH ROLL-OUT
SWITCH
CAUTION:
IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE
APPLIIANCE MUST BE REPLACED, IT MUST BE REPLACED
WIT H TY PE 105∞C OR ITS EQUIVALENT.
WIRE LEGEND:
FACTORY WIRED
FIELD WIRED, FIELD SUPPLIED
BLOWER
(INDUCER)
LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS.
PROPER OPERATION AFTER SERVICING".
1
CIRCULATOR
MV
GND
VR8204A
1
JUNCTION
BOX
DISCONNECT
SWITCH
120V/60Hz
AQUASTAT
RED
WHITE
BLACK
L1-HOT
L2-NEUTRAL
1
2
M
BLACK
1
2
3
6
5
4
P5
P4
BLACK
G/Y
1
2
3
4
1
2
3
P2
BLACK
WHITE
GREEN
PROVIDE DISCONNECT MEANS & OVERLOAD PROTECTION AS
REQUIRED.
120V/24V
TRANSFORMER
12
BLACK
WHITE
BROWN
PINK
1
2
3
4
5
6
7
8
9
PV
MV/PV
L4080B
GAS VALVE
24V
THERMOSTAT
RED
BLUE
WHITE
RED
BLACK
YELLOW
YELLOW
P6
P3
P1
GREEN
WHITE
WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION.
"VERIFY
RED
Figure 13a. Schematic wiring diagram.

VICTORY VSP Models 17
MU TIZONING OF VSP BOI ER
ZONE VALVE SYSTEM USING V8043E/ ZONE VALVES
Figure 14.
MU TIZONING OF VSP BOI ER
PUMP ZONING SYSTEM USING R845A RELAY
Figure 15.
MU TIZONING OF VSP BOI ER
PUMP ZONING SYSTEM USING R882A/B RELAYS
Figure 16.

VICTORY VSP Models
18
2. Power Connection
A. Remove electrical junction box cover.
B. Hot connection lead is black. Neutral connection lead is white.
roper polarity is important for VSP boilers. Reversed
polarity will cause system lockout and the power LED will
flash continuously.
C. Connect ground wire to ground screw inside the junction box.
D. Replace junction box cover.
THERMOSTAT CONNECTIONS
Install thermostat on an inside wall and away from any heat
sources, sunshine and drafts. Thermostat wires must be connect-
ed to terminals block on boiler. See wiring diagram igure 13a.
Thermostat heat anticipator: or a non-zoned system set thermo-
stat heat anticipator to 0.4 Amps, for zoned system set to match
power requirements of zone valves or relays. Refer to manufactur-
er’s instructions and specifications. Also see instructions with ther-
mostat.
MULTI ZONING
or multiple zoning, either zone valves or circulators maybe used.
or zone valve system see igure 14.
or pump zoning system see igure 15 and igure 16.
DO NOT use boiler transformer to power external accessories like
zone valve and relays, overload and/or burned-out transformer
and boiler malfunction can result. Use separate transformer to
power such components. or pump zoning system, remove boiler
circulator wire connector from P5 of electronic boiler control (See
igure 13b).
WATER I ING
Always follow good piping practices. Observe minimum 1" clear-
ance to combustibles around all uninsulated hot water pipes or
when openings around pipes are not protected by non-com-
bustible materials.
On a hot water boiler installed above radiation level, the boiler
must be provided with a low water cutoff device at the the time of
installation by the installer (see igure 17 for piping arrangement).
The low water cutoff must be wired in series with rollout safety
switch and Aquastat (limit control). See wiring diagram igure
13a.
1. Supply and Return
or tapping sizes see dimensions on page 2. Shut-off valves
are recommended.
2. Circulating Systems
Victory VSP boilers are equipped with a water circulating
pump mounted to the return water connection on the boiler.
This pump location is appropriate for most installations. It
may be desired and proper to locate this pump to the alter-
nate location shown in igure 17, especially when applied to
larger systems using high-head pumps.
When the pump is removed there is a 11⁄2" PT tapping
that the return pipe may be attached to.
At one month intervals after the last call for heat, the circula
tor will be energized for 30 seconds. Short operation after
long term idle periods prevent damage of the pump from
sedimentation.
3. Radiant Floor, Low Water Temperature and Large Water
Volume Systems
A boiler by-pass loop, three way valve arrangement, or
primary secondary pumping (with a boiler loop) must be
used to provide a minimum 130˚ return water temperature to
the boiler. This will prevent condensation on the cast-iron
sections that can result in improper operation of the boiler.
Model ounds Gallons
VSP-60 24.75 3.0
VSP-90 32.00 3.8
VSP-120 39.25 4.7
VSP-150 46.50 5.6
VSP-180 53.75 6.4
Boiler Water Content
GATE VALVEGATE VALVE
FACTORYFACTORY
CIRCULATORCIRCULATOR
LOCATIONLOCATION
3/4"PRESSURE3/4"PRESSURE
RELIEFVALVERELIEFVALVE
AIRVENTAIRVENT
RETURNRETURN
SUPPLYSUPPLY
EXPANSIONEXPANSION
TANKTANK
ALTERNATEALTERNATE
CIRCULATORCIRCULATOR
LOLOCATCATIONION
FLOWCONTROLFLOWCONTROL
VALVEVALVE
WATERFEEDWATERFEED
PRESSUREPRESSURE
REDUCINGREDUCING
(FILL)VALVE(FILL)VALVE
DRAINCOCKDRAINCOCK
Figure 17. Piping arrangement

VICTORY VSP Models 19
4. Air Control System
Diaphragm type compression tank is used to control system
pressure. It must be installed at the boiler or between boiler
and supply main pump(s).
An automatic air vent is used to remove air from the system
in igure 17. If system pressure needs further control, add
an additional tank in parallel with original tank or install a
larger capacity tank. Use appropriate size tank for volume of
water in system. See chart for boiler’s volume.
5. Cold Water Fill
Pressure reducing (fill) valve and shut-off valve should be
installed.
6. Relief Valve Discharge Piping
Use same size or larger piping than valve outlet. Must ter-
minate 6" minimum from floor with a plain (no threads)
end. Place a bucket under pressure relief valve discharge.
Make sure discharge is always visible. DO NOT hard-pipe
to drain piping.
7. Providing Protection from Freezing
Anti-freeze is sometimes used in hydronic heating systems
to protect against freeze-up in the event of power failure or
control shutdown when the building is unoccupied. It
should be recognized that unless the building is kept
above freezing temperature by some means, the plumbing
system is not protected. Two types of anti-freeze may be
used: ETHYLENE GLYCOL, used in automobiles, has
desirable properties, but is toxic. Its use maybe prohibited
when system water/glycol solution is in contact with a
potable water vessel (as an indirect hot water heater with
built-in heating coils). PROPYLENE GLYCOL is used in
the quick-freeze food industry; it is practically non-toxic. Its
use may be permitted when system solution is in contact
with a potable water vessel. When anti-freeze must be
used, inhibited propylene glycol is recommended. Useful
information on the characteristics, mixing proportions, etc.
of glycol in heating systems is given in Technical Topics
No. 2A, available from the Hydronics Institute, 34 Russo
Place, Berkeley Heights, NJ 07922. Consult glycol manu-
facturers for sources of propylene glycol.
8. Water Treatment
A good water treatment program will not only extend the
useful life of this boiler but it will also save much of the
time and expense of repairs made necessary by pre-
ventable occurrences. A reputable water treatment compa-
ny should be consulted to evaluate and determine the best
overall treatment program for your boiler equipment.
PIPING A HEATING - COO ING SYSTEM TO A WATER
BOI ER AND CHI ER
igure 18 illustrates a method of piping a heating-cooling sys-
tem to a water boiler and a chiller. Hand valves (shown) or
automatic valves must be installed to prevent circulation of
chilled water in the boiler or hot water in the chiller.
The air control system and pressure control system must
operate with chiller only, or the boiler only, being valved to the
piping system. Separate control devices on the boiler and
chiller may be used, or a single set of air and pressure con-
trols on the common piping may be preferred.
If the boiler is used to supply hot water to heating coils in air
handling units, flow control valves or other devices must be
installed to prevent gravity circulation of water in the coils dur-
ing the cooling cycle.
O ERATING INSTRUCTIONS
I. Filling and Venting Water Systems
A. ill the system with water. Vent or purge of air.
B. ire the boiler as soon as possible (see following warn-
ing and instructions) and bring water temperature in
the system.
C. Vent air and add water as needed to achieve operating
pressure on boiler gauge. Pressure must be between
approximately 12 psi (cold water) and 25 psi at water
temperature setting of high limit control, for boilers
equipped with 30 psi relief valves. Boilers rated for a
higher pressure and equipped with a matching relief
valve may operate at a higher pressure, but no higher
than 5 psi below the relief valve opening pressure.
D. Check for and repair any leaks before placing system
in service.
BEFORE FIRING BOILER, make these checks:
1. System is full of water. Air is vented or purged.
2. Relief valve is installed in accordance with ASME Boil-
er and Pressure Vessel Code, Section IV. Valve open-
ing is not closed or reduced in size.
3. Venting is installed according to instructions under
“ LUE GAS VENTING REQUIREMENTS”.
4. All wiring is completed, following applicable wiring dia-
grams.
5. Using soap solution, check for gas leaks in all gas pip-
ing from meter to boiler pilot and manifold. DO NOT
use open flame.
Figure 18. Cooling system to a water boiler and chiller.

VICTORY VSP Models
20
II. Initial Start
Safe lighting and other performance criteria were met when
testing various gas manifold and control assemblies used
on the Victory VSP Series Boilers under the ANSI Z21.13-
latest edition.
Instructions
ollow the lighting instructions in this manual. These
instructions are also attached to the boiler.
SAFETY INFORMATION
or Your Safety Read Before Operating
A. This appliance is equipped with an ignition device which
automatically lights the pilot. DO NOT try to light the pilot by
hand.
B. BE ORE OPERATING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
• DO NOT try to light any appliance.
•DO NOT touch any electric switch: DO NOT use any
phone in your building.
• Immediately call you gas supplier from a neighbor’s
phone. ollow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire depart-
ment.
C. Use only your hand to turn the gas control knob. Never
use tools. If the knob will not turn by hand, don’t try to
repair it, call a qualified service technician. orce or
attempted repair may result in a fire or explosion.
D. Do Not use this appliance if any part has been under
water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the
control system and any gas control which has been under
water.
1. STOP! Read the safety information above.
2. Set the thermostat to lowest setting.
3. Turn off all electric power to the appliance.
4. This appliance is equipped with an ignition device which
automatically lights the pilot. DO NOT try to light the pilot by
hand.
5. Remove jacket front panel
6. Turn gas control knob clockwise to “O ”.
DO NOT force.
7. Wait five (5) minutes (longer for propane) to clear out any
gas, then smell for gas, including near the floor. If you then
smell gas, STOP! ollow “B” in the safety information
above on this page. If you don’t smell gas, go to next
step.
8. Turn as control knob counterclockwise to “ON”.
9. Replace jacket front panel.
10. Turn on all electric power to the appliance.
11. Set thermostat to desired setting.
12. If the appliance will not operate, follow the instructions
“To Turn Off Gas to Appliance” and call your service
technician or gas supplier.
To Turn Off Gas to Appliance
1. Set thermostat to lowest setting.
2. Turn off all electric power to the appliance if service
is to be performed.
3. Remove jacket front panel.
4. Turn gas control knob clockwise till knob stops,
then continue to “O ”. Do not force.
5. Replace jacket front panel.
Removing Jacket Front anel
1. Turn black screws 1⁄4turn to open position.
2. Remove front panel.
To replace the panel, reverse procedure.
Gas Input Rate Adjustment
1. Consult gas supplier for higher heating value* of gas
(Btu/cu. ft.)
2. Set thermostat high enough so that boiler will remain on
3. Measure manifold pressure.
Correct manifold pressure for gas used is printed on boiler
rating plate. NOTE: Gas pressure may be adjusted by
turning pressure regulator screw on combination gas valve
(turn clockwise to increase pressure, counterclockwise to
decrease pressure).
* ”Higher Heating” value of gas is commonly known as “heating value”.
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing property
damage, personal injury or loss of life.
0FF0FF
ONON
HONEYWELLHONEYWELL
GASGAS
INLETINLET
GASCONTROLKNOBGASCONTROLKNOB
SHOWNIN"OFF"SHOWNIN"OFF"
POSITIONPOSITION
OUTLETOUTLET
VSP40-19
FIGURE19
Figure 19.
Gas Valve VR8204 or VR8304
OPERATING INSTRUCTIONS