SLI ENFORCER MAE-P317-01Q User manual

ENFORCER PASSIVE STEREO BALUN
4SECO-LARM U.S.A., Inc.
MAE-P317-01Q MAE-P337-01Q
Audio
Signal Type
A
nalog stereo
Max. range 2,500’ (760m)
Bandwidth 10Hz to 50KHz ±3dB
Maximum input 1Vpp
Insertion loss ≤1dB
Return loss ≥15dB over the frequency range
Common mode rejection Greater than 40dB
Power No power required for audio
Connections
Wire type UTP (unshielded twisted pair)
Wire category 20 - 24 AWG @ screwless terminal blocks
Cat2 or better, Cat5e ideal, Cat6 improves range
Connectors In 2 (two) RCA plugs 3.5mm plug
Out RJ-45 jack
Impedance In 600 ohms
Out 100 ohms
Other
Dimensions 2
1
/
8
” x 1
1
/
8
” x 1” (54 x 29 x 25 mm)
Max. humidity 95%
Temperature Range 32° ~ 131° F (0° ~ 55° C)
Case
A
BS plastic
WARRANTY This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is
limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines
that such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only,
at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential
personal or property damages of any kind to the purchaser or anyone else.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right
to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2009 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in
whole or in part, without the written permission of SECO-LARM.
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Tel: [phone] Fax: [phone] E-mail: sales @ seco-larm.com
Mi-MAE-P3x7-01Q
_
0902.docx
PITLW2
Specifications:
Troubleshooting:
No sound •Check to make sure polarity is correct.
•Make sure the maximum distance of the UTP does not exceed the
maximum range of the balun.
•Make sure all connections are snugly in place.
•Check to make sure RJ-45 connector is crimped correctly and wired
according to T568B wiring standard.
MANUAL
Passive Stereo Baluns
The ENFORCER Passive Stereo Baluns are the quick, low-cost way to connect audio devices at
greater distances than traditional audio cabling methods. The stereo baluns work in pairs to allow
analog audio signals to be transmitted over low-cost Cat5e/6 unshielded twisted pair (UTP) cable.
•
Passive operation – No external power
required
•Uses low-cost Cat5e/6 cable instead of costly
coax cables
•Small size for easy installation
•
High immunity from interference – Built-in
impedance coupled device and noise filter
•Gold-plated connector for lon
g
er life and better
reliability (MAE-P317-01Q only)
•Limited lifetime warranty
NOTE: Products with a model number that ends with “Q” or have a round green “Q” sticker represent RoHs compliant products.
MAE-P317-01Q MAE-P337-01Q
Analog StereoBalun 3.5mm Stereo Balun

ENFORCER PASSIVE STEREO BALUN
2SECO-LARM U.S.A., Inc.
Please use T568B wiring standard
Overview:
Installation:
1. Make sure the maximum distance between the audio source and destination does not
exceed the maximum range of the stereo baluns.
2. Run the UTP cable from the audio source to where it will be connected to the destination.
Follow the audio source’s wiring instructions for information on how to safely run and hide
this wire.
3. Connect UTP cable to the two audio baluns connecting the RJ-45 plug according to T568B
wiring standards.
NOTE: The baluns are polarity-sensitive. Observe correct polarity.
NOTE: Stereo baluns are connected in pairs. One connects to the audio source, and the other
connects to the audio destination.
The stereo baluns can be mixed and matched, with both baluns being of the same type,
or one being a 3.5mm stereo type and the other being an analog stereo type.
4. Plug the audio baluns into the connectors on the source and destination.
5. Test the connection by powering up the audio source and destination.
MAE-P317-01Q
RJ-45
j
ack Stereo L
(
white
)
Stereo R
(
red
)
MAE-P337-01Q
RJ-45
j
ack
3.5mm
p
lu
g
Figure 1 – RJ-45 jack wiring diagram:
–
+
–
+
1 2 3 6
Stereo L Stereo R
ENFORCER PASSIVE STEREO BALUN
SECO-LARM U.S.A., Inc 3
Sample Application #1: Portable Music Player or Computer
Sample Application #2: Analog Stereo Signal
SECO-LARM has a complete line of audio/video products.
Please visit www.seco-larm.com for more information.
Up to 2,500’ (760m)
Portable Music
Player or Compute
r
MAE-P337-01Q MAE-P317-01Q
Amplifier
Up to 2,500’ (760m)
Analog Stereo
Source, VCR,
Cassette Deck
Amplifier
MAE-P317-01Q MAE-P317-01Q
Sample Application #3: Connecting a Stereo Source to a Computer
MAE-P317-01Q
Up to 2,500’ (760m)
MAE-P337-01Q
Analog Stereo
Source, VCR,
Turntable
Computer