Sliger SV590 User manual

SV590
Vertical Mini-ITX PC Case - Build Guide V1.0

SCREWS
The SV590 comes with a total of 5 different screws.
For the purposes of this guide we will assign a unique color to each
of the screw to signify their locations through out this guide.
GREEN M3 x 6mm PAN HEAD
Securing PCIe Cards
RED M3 x 5mm FLAT HEAD
Radiator Mount Bracket
Power Cord Mount Bracket
SSDs / SSD brackets
VIOLET 632 x 1/4” TRUSS HEAD
Motherboard
Power Supplies
PINK M3 x 8mm FLAT HEAD
Power Cord
ORANGE 632 x 1/4” FLAT HEAD
Side Panels
Base Plate
Radiators
3.5” Hard Drives (on bottom of case)

EASY OFF TOP
The top cover features tool-less removal via ball-stud mounting points,
this allows for convenient access to your motherboard and PCIe card IO
ports in place of traditional front panel IO ports.
The top panel may be very tight on the first few times on/off.

SIDE PANELS
Side panels of the SV590 are held on via 8x 632 X 1/4” FLAT HEAD screws.
Four per side, two at top and two at bottom.
Please be careful to use the correct size screw driver head as to not
strip the screw heads,
GPU SIDE REAR CORNER CPU SIDE FRONT CORNER

SLIDE OFF PANELS
Once the screws are removed, the front/GPU side panel slides off the front,
and the rear/CPU side panel slides off the back of the case.
Panels may scratch the case frame, please handle them carefully.

CASE FRAME
The rear radiator mount bracket of the SV590 frame is held on by
6x M3x5mm FLAT HEAD screws; 3x per side, 2x at top and one at bottom.
You will also need to unscrew the SSD mount bracket which is held on
by and additional 2x M3x5mm FLAT HEAD screws.

FRAME SEPARATION

POWER CORD
The SV590 includes an
internal power cord
extension, and a mount
bracket for easy access
to the extension plug.
There is also a pass
through grommet tothrough grommet to
get the extension into the
case. Clip this grommet
over the cord, then run
the cord through the
cutout, and slide the
grommet into position as
shown at left.shown at left.
The power cord extension is then installed into the mount bracket with
two M3x8mm FLAT HEAD screws.
Once the power cord is installed both into the bracket, and into the grommet
the bracket then can be attached to the case via 2x M3x5mm FLAT HEAD
screws.
Note that the SV590
power cord mountpower cord mount
is adjustable to
four different positions
in order to allow the
user to position it
where it obstructs the
motherboard IO ports
the least.the least.
It is critical you install
the power cord before
installing the IO shield
for your motherboard!

POWER SUPPLY
The fan on the power supply is recommended to be positioned with the
fan side of the power supply towards the center spine of the case, this
orientation will result in better overall system temperatures and lower noise.
Once positioned, the SFX PSU can be attached to the PSU Mounting Bracket
with up to 6x of the included 632 x 1/4” TRUSS HEAD screws.
Note that not all SFX Power Supplies have all 6x screw holes as shown.

MOTHERBOARD
Don’t forget to install the power
cord and your IO shield first!
Some CPU coolers may require a
back plate installed before installing
the motherboard into the case.
It is advised to also check that any
back of motherboard M.2 drives are back of motherboard M.2 drives are
installed before mounting the
motherboard.
Once the IO shield and power cord /
power cord grommet are properly
installed the motherboard can now
be mounted using 4x 632 x 1/4”
TRUSS HEADTRUSS HEAD screws.
A Phillips #2 screw driver with a
minimum 3” shaft length is
recommended for installing these
screws. Both of the screws on the
PCIe slot side of the motherboard
have pass-through holes in the
case frame to allow the screw drivercase frame to allow the screw driver
and screw to pass through and be
screwed in straight.
Additional installation instructions
for your CPU, CPU cooler, RAM,
etc. are covered by your
motherboard or coolers respective
user manual.user manual.

CABLE MANAGEMENT
Once the motherboard and power
supply are mounted it is
recommended to do some cable
management before we install any
radiators or PCIe cards.
Note the CPU and cooler mount back
plate / standoffs are installed.plate / standoffs are installed.
The power switch/LED is routed and
plugged into the motherboard.
The power cord is mounted at
top (two screws in counter sinks)
and properly passed through
the grommet, and routed to the
inlet on the power supply.inlet on the power supply.
(Also be sure to check that your
PSU switch is set to on!)
Motherboard power cables are
plugged in, and GPU power
cables are loosely positioned.
Power cables are loosely managed
and zip tied.and zip tied.
The PCIe riser is plugged into the
PCIe slot on the motherboard.

240mm / 120mm AIO
The compact design of the SV590 limits
the ways in which dual AIO setups can
be installed.
The 240mm AIO at left, shown in orange,
must be mounted above the 120mm AIO
with the radiator hoses facing
downward.downward.
The 120mm AIO must be mounted
below the 240mm AIO, with the 120mm
AIO hoses able to be oriented to the
top or bottom of the case.
If the 240mm AIO hoses are mounted
to the top, you will not be able to
screw the case together - as the hosesscrew the case together - as the hoses
will hit the motherboard and/or GPU.
Conversely if the hoses are mounted
as shown, the hoses will come out
where there is additional free space
next to the power supply / below the
GPU/PCIe cards.
If your AIOs do not include mountingIf your AIOs do not include mounting
screws please use the 632 x 1/4” TRUSS
HEAD screws provided with the case.
ALL FANS MUST BE SET TO EXHAUST OUT THE REAR OF THE CASE
If installed as intake you will cause your power supply and GPU to run
at high temperatures which can cause part failures.

360mm AIO
NOTE: All 360mm AIOs or radiators in
the SV590 must be mounted with the
radiator hoses/ports at bottom.
If the 360mm radiator
hoses are mounted
to the top, you will not
be able to screw the
case closed as the
hoses will collide
with the motherboard with the motherboard
and/or GPU PCIe riser
bracket.
Conversely if the hoses
are mounted as shown,
to the bottom of the case,
the hoses will not have
interference issues due interference issues due
to free space provided
around the power supply
and below the GPU/PCIe
cards.
If your AIOs do not include
mounting screws please
use the use the 632 x 1/4” TRUSS
HEAD screws provided with
the case.
ALL FANS MUST BE SET TO EXHAUST OUT THE REAR OF THE CASE
If installed as intake you will cause your power supply and GPU to run
at high temperatures which can cause part failures.

REASSEMBLE CASE
We recommend plugging in your
fan headers / fan splitters before
screwing the rear radiator
bracket back onto the case frame.
It is also recommended to do
try various positions with the AIO
CPU pump block to best fit yourCPU pump block to best fit your
AIO hoses as lengths can vary.
With the radiator/AIO in position
your case should look like the example
to the right, less your GPU and
any 2.5” SSD / 3.5” HDDs.
Mounting the AIO/radiator is the reverse order of page 5 in this guide.
The rear radiator mount bracket of the SV590 frame is held on by
6x M3x5mm screws; 3x per side, 2x at top and one at bottom.

GPU MOUNTING
We recommend installing the GPU
after installing the radiator as the
case will be slightly more rigid.
Additionally this method allows
access to the fan screws for ease
of installing fan guards, reversing
fan airflow, etc.fan airflow, etc.
Process of installing the GPU is
same it would be on a standard PC
case, just on a PCIe riser. Slide the
card into position, push
down into the slot, and then secure
the PCIe card bracket with the M3
PPAN HEAD screws.
If your GPU only has a 2-slot wide
PCIe bracket the SV590 includes
a single color matched slot cover.

SSD and HDDs
The SV590 3x SSD bracket
can be mounted in one of
a few positions on either
side of the case.
The SSD bracket itself
is symmetrical on mounting,
but asymmetrical on SSDbut asymmetrical on SSD
position to allow SSDs to
be offset for better cable
management and AIO
tube routing.
Two placement examples are
shown. Motherboard side
example at top, and GPU
side example at left.
The SSD bracket is mounted
via 2x M3 x 5mm flat head
screws.screws.
SSDs are mounted to this
bracket with up to 4x M3 x
5mm flat head screws each.

SSD and HDDs (cont)
The SV590 also has a
section of standard
obround venting at the
bottom of the case for
attachment of 3.5” Hard
Drive Disks and 2.5” SSD
directly to the frame directly to the frame
when stood on end.
Two configurations are
show, at right with 2x
3.5” HDDs, and 1x 2.5”
SSD, and below with 5x
2.5” SSD.
All SSDs in this position
should be mounted with
2x M3 x 5mm FLAT HEAD
screws per SSD.
3.5” Hard Drive Disks should
be mounted with two 632 X
1/4” FL1/4” FLAT HEAD screws.

BASE PLATE
The SV590 removable base plate is attached
via 4x 632 X 1/4” FLAT HEAD screws.
Alignment of the rectangular cutout in the base plate to the obround
vent pattern of the chassis frame before attachment is critical.
This cutout in the base plate is here so that screws for mounting SSD, HDDs,
or custom loop pumps and/or reservoirs do not cause the case to sit uneven.
Other manuals for SV590
2
Table of contents
Other Sliger Enclosure manuals

Sliger
Sliger CL530 User manual

Sliger
Sliger CL530 User manual

Sliger
Sliger SV590 User manual

Sliger
Sliger CERBERUS Manual

Sliger
Sliger SM5X0 Series User manual

Sliger
Sliger S610 User manual

Sliger
Sliger SM570 User manual

Sliger
Sliger SM550 User manual

Sliger
Sliger SM580 User manual

Sliger
Sliger SM5X0 Series User manual