Sliger S610 User manual

S610
Build Guide

RED M3 x 5mm FLAT HEAD
SSDs (on SSD bracket)
USB and Power Button Bracket
SCREWS
GREEN M3 x 6mm PAN HEAD
Securing PCIe Cards
SSD
PINK M3 x 8mm FLAT HEAD
Power Cord Inlet
The S610 comes with a total of 6 dierent screws. For the purposes of this guide we
will assign a unique color to each screw to signify their locations in this guide.
BLUE 6-32 x 1/4” FLAT HEAD
Handle Bracket
SFX PSU Brackets
Side Fan / Radiator Bracket
GREY M3 x 12mm SOCKET CAP
Case Handle

EASY-OFF PANELS
RE-ASSEMBLY NOTES
Side panels are reversible to either side.
Front Panel can be installed with either end at top or bottom.
The front, side panels, top and bottom all have tool-less removal via their ball-
stud mounting points. Careful, panels may be very tight on the rst few times
on/o.

Power Button Location
The S610 has two power button locations allowing you to choose what orientation
the case is. Either with the GPU on the bottom of the case, or GPU on the top of
the case. Here is the process on removing the power button switch panel and
installing it onto the other location.
Step 1
Remove 4x M3 x 5mm FLAT HEAD
Step 2
Tilt the Power Button Panel as shown in
the photo.
Step 3
Slide the Power Button Panel towards the
inside of the chassis.

Power Button Location Cont.
Step 4
Flip over the chassis so the bottom is now the top.
Step 5
Tilt the Power Button Panel as shown in
the photo and reinsert the panel from
inside of the chassis.
Step 6
Reuse the 4x M3 x 5mm FLAT HEAD
screws to secure panel.
End Result

MOTHERBOARD
Be sure to install your IO shield rst!
Some CPU coolers and AIOs may require a back plate to be installed before
installing the motherboard into the case. Once the IO shield is properly installed
the motherboard can now be mounted using 4x 6-32 x 1/4” HEX HEAD screws.
A Phillips #2 screw driver with a minimum 3” shaft length
is recommended for installing these screws.

SSD MOUNTING
The S610 has a two SDD mounting locations on the SFX PSU Length-wise
bracket. Each SSD attaches to the bracket with 2x M3 x 6mm PAN HEAD
screws. Be sure to install drives with the SATA power and data connections facing
the same direction as PSU power connections.

POWER SUPPLY INSTALLATION
Lastly, the SFX PSU mounting bracket is
secured to the case spine via 2x 6-32 x 1/4”
FLAT HEAD screws. These screws are
located at the top middle of the spine, next
to the motherboard corner stando. There
are also 2x 6-32 x 1/4” FLAT HEAD screw
locations behind the front panel of the case.
Install the power pig-tail by snaking it
through the rear chassis hole and securing it
with 2x
M3 x 8mm FLAT HEAD screws. Then
insert into the SFX PSU.
The SFX PSU attaches to the bracket with 3x
6-32 x 1/4” HEX HEAD screws.

WIDTH-WISE PSU INSTALLATION
Then SFX PSU mounting bracket is secured
to the case spine via 4x 6-32 x 1/4” FLAT
HEAD screws as shown in the photo.
Install the power pig-tail by snaking it
through the rear chassis hole and securing it
with 2x
M3 x 8mm FLAT HEAD screws. Then
insert into the SFX PSU.
The SFX PSU attaches to the Width-wise
bracket with 6x 6-32 x 1/4” HEX HEAD
screws.

PCIe CARD
The PCIe card is secured with up to 3x M3 x 6mm PAN HEAD screws.
NOTE: Depending on your GPU card size. You may have to try dierent
angles and approaches to get it in the chassis and seated into the PCIe
slot.
Then install the PCIe Top cover with 1x 6-32 x 1/4” FLAT HEAD screw.

120/240/280mm AIO INSTALLATION
The S610 supports a variety of water-cooling / AIO setups. The three dierent
congurations are; a 120mm AIO installed on the PSU Bracket, a 240mm radiator
attached to the side bracket, or a 280mm radiator attached to the side bracket.
The 120mm radiator can be mounted to the PSU bracket as shown in the image
below. Using 4x 6-32 x 1/4” HEX HEAD screws to secure it to the bracket.
Hoses must come out of the radiator facing the open side of the case as shown.
NOTE: You must attach radiator rst before installing your SFX PSU.

240/280mm AIO INSTALLATION CONT.
The S610 side bracket supports either a 240mm or 280mm radiator. Fans are
recommend to be mounted on the inside exhausting air out the side panel through
the radiator.
NOTE: For the 280mm radiator, it is best to set the radiator inside the case after
getting the water block secured to the CPU, and then placing the side bracket over
the radiator. Secure the radiator to side bracket with 4x to 8x 6-32 x 1/4” HEX
HEAD screws. Lastly, the side bracket is attached to the chassis with 4x 6-32 x 1/4”
FLAT HEAD screws.

The S610 side bracket can t 2x 120mm or 140mm fans.
SIDE BRACKET FANS
120mm
140mm

The S610 can t 2x 120mm slim 15mm fans mounted on the top of the
chassis.
NOTE: The case handle bracket can not be used with this conguration.
TOP MOUNTED FANS

The S610 supports up to 120MM by 25mm,
NOTE: Fan can only when used in conjunction with the "Width-wise"
PSU Bracket.
FRONT FAN
120MM by 25mm

The S610 supports either an 80mm or 92mm fan mounted on the rear of
the chassis. Use standard KB5 screws to attach the fan.
REAR FAN
80mm
92mm

SSD MOUNTING
The S610 has an optional SSD window bracket. Each SSD attaches to the bracket
with 2x M3 x 6mm PAN HEAD screws. The assembly then attaches to the chassis
with 2x 6-32 x 1/4” FLAT HEAD screws.
NOTE: When using the SSD Window Bracket, You CAN NOT use the side bracket for
fans or radiator, but you can pair the SSD window bracket with our 120mm AIO kit.

CASE HANDLE BRACKET
The S610 case handle bracket can be mounted in two dierent locations show in
the photos below. They are attached to the chassis with 4x 6-32 x 1/4” FLAT
HEAD screws.
GPU Bottom Orientation
GPU Top Orientation
NOTE: A 120mm by 15mm thick fan can
be mounted to the case handle bracket.
Use 4x KB5 screws to attach fan to
bracket. Note: KB5 screws not
included.

Case Handle is attached with 2x M4 x 12mm Socket Cap
Use the included Allen key to tighten.
NOTE: Do not over-torque screws
CASE HANDLE