SLS K2 User manual

1. K2 Dual Core Unit
2. USB 2.0 A Male-Micro B Male Cable : 1meter
3. HDMI 1.4 Cable Male to Female : 1foot
4. Antenna
5. High Quality Velcro
6. Getting Started with K2DC
Getting Started
K2 Dual Core System
2. Connect Ethernet Cable to
K2DC and another end to
Network Device
(Hub or Switch or Router).
3. Connect HDMI Female to
K2DC and HDMI Male end
to TV or Projector.
4. Connect USB A type Male end of USB Cable
to 5V 1A DC power supply to switch board
and switch it ON.
5. Android OS starts booting. After few
seconds, Homepage will appear.
1. Connect Micro USB Cable
and connect the antenna to
K2DC.
What’s in the box?
Starting K2DC System
For More information on K2DC usage, visit
http://www.slscorp.com/products/k2-dual-core-system.html
For any support, queries and suggestions, contact us at [email protected].

Informativa agli utenti
Ai sensi dell'art. 26 del Decreto Legislativo 14 marzo 2014, n. 49 "Attuazione della direttiva
2012/19/UE sui rifiuti di apparecchiature elettriche ed elettroniche (RAEE)"
Il simbolo del cassonetto barrato, riportato sull'apparecchiatura, indica che il
prodotto alla fine della propria vita utile deve essere raccolto separatamente
dagli altri rifiuti ed avviato a recupero o eventuale smaltimento secondo
specifiche modalità e tramite soggetti autorizzati
La raccolta differenziata della presente apparecchiatura, qualora giunta a fine
vita, è organizzata e gestita dal produttore.
Il Punto di Vendita che intenda disfarsi della presente apparecchiatura, in quanto guasta,
danneggiata o obsoleta, è tenuto per legge a contattare Lottomatica, tramite le modalità
previste dal servizio di assistenza tecnica, al fine di richiederne ed organizzarne la riparazione
o il ritiro e sostituzione.
Per maggiori dettagli sulle modalità di recupero e smaltimento degli AEE professionali di
Lottomatica si faccia riferimento alla relativa sezione del Portale Rivenditori
www.rivenditorilottomatica.it
SLS Part Number : DOC0001 September 2017 Version : 1.1

FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is
connected.
•Consult the dealer or an experienced radio/TV technician for help.
•This device and its antenna(s) must not be co-located or operating in conjunction
with any other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of 20 cm
between the radiator and your body.

IC statement
“This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the
following two conditions:
1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired
operation of the device.”
« Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement. »
Cet équipement est conforme aux limites d'exposition aux rayonnements ioniques du CI établies
pour un environnement non controlé. Cet équipement doit être installé et utilisé avec une
distance minimale de 20 cm entre le radiateur et votre corps.
This radio transmitter (identify the device by certification number) has been approved by Industry
Canada to operate with the antenna types listed below with the maximum permissible gain
indicated. Antenna types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device. The equipment just has one
model antanna, Dipole type, and antanna gain is 3dBi.