Smart Park CCS-562 User manual

CCS-562
CCS-702
Installation and
Operating manual
Version 562.2/702.2

Introduction
Thank you for purchasing/installing a Smart Park™ commercial camera system.
These instructions are intended for use by an authorized Smart Park™ installer.
Modifications, manipulation or improper repairs to this product can affect the
operability and safety. Modifying this product in any way or using this product
for anything other than it’s intended use may invalidate the product warranty.
1. Parts Check Off List
Camera
LCD Monitor
3 Wire Power loom
Extension Cable (Camera to controller)
Extension Cable (Controller to LCD Monitor)
Monitor Stand
Installation Screws/Stickers
2. Required Tools
• Digital Multimeter
• Wire Cutters/Stripper
• Power Drill
• Socket Set
• Screwdrivers
• Tape Measure
• Marker Pen/Pencil
• Panel Removal Tool
• Safety Glasses

4.1 Attach the camera mounting bracket to the vehicle.
4.2 Mount the camera on the mounting bracket, adjust the angle to suit and
fasten the screws firmly.
4.3 Install the wiring harness with accesory and reverse power as per the
wiring diagram.
4.4 Run the extension cable from the camera to the wiring harness.
4.5 Run the connection from the wiring harness to the LCD monitor location.
NOTE: Protect all cabling by running the cable inside the vehicle or using
conduit where this is not possible.
4. Camera Installation
3. Wiring Diagram

5. LCD Monitor Installation
•、 Install the monitor on a surface which will support more than 4 Kg (9Lbs)
of weight
•、 Install the monitor away from a speaker mounted in the vehicle so the
picture is not distorted by the speaker’s magnetic field.
•、 Don’t install the unit in an extremely hot or humid place (radiator, air duct, etc.)
or in a place subject to direct sunlight, excessive dust, mechanical vibration
or shock.
5.1 Attach the supplied mounting bracket to the ceiling or the floor, etc.
5.2 Adjust the angle of the monitor and fasten the screws firmly.

6. System Connection
7. Attach the Smart Park sticker to the
window.
Installation is now complete.

OPERATING INSTRUCTIONS
1. The reverse camera system will automatically activate whenever the vehicle
is placed in reverse gear.
2. The POWER button can be used to manually turn the monitor on or off at
any time.
NOTE: Your camera must have power or no image will be seen. Some
vehicles will only have power to the camera when in reverse.
3. To change between the 2 camera inputs (CAM1 / CAM2) press the
CAM SEL button (Vehicle must be equipped with 2 cameras).
4. Pressing the MENU button scrolls through the settings available including
VOLUME, BRIGHTNESS, AUTO BRIGHTNESS, CONTRAST, HUE,
SATURATION, MIRROR, RESET, LANGUAGE. Use the UP & DOWN
buttons to adjust the settings.
5. The MIRROR option will allow you to reverse the image from either camera
as required.
6. Pressing & Holding the POWER button for 2 seconds shuts the
system down.

SPECIFICATIONS
MONITOR
LCD Profile Wide-Screen Ratio° 5.6” Inch 4:3
7” Inch 16:9
View Angle (U/D/L/R) (CR>10) 50/70/70/70
Brightness (cd/m2) 500
Contrast Ratio 500:1
Response Time (ms) (at 25°) 10
Power Requirements DC 12v~24v
Power Consumption 5W
Operating Temperature Range -30 ~ +85、
Storage Temperature Range -30 ~ +85、
Dimension 5.6” Inch 165 (L) x 115 (W) x 29 (D) mm
7” Inch 200 (L) x 115 (W) x 29 (D) mm
Weight Approx 5.6” Inch 340g
7” Inch 400g
CAMERA
Image Type Color CCD
Picture Elements 0.44m pixels / 0.29m pixels
Image Size 1/3 Inch, 1/.4 Inch
Lens Focal length 2.8mm/2.5mm
Synchronization Internal
Horizontal Resolution 420 TV Line
Signal to Noise Ratio 48dB
Power Supply 12V/24V DC
Power Consumption 1.5W
Operating Temperature Range -30 ~ +85、
Storage Temperature Range -30 ~ +85、
Dimension 82 (L) x 73 (W) x 58 (D) mm
Weight Approx (Including Mounting Bracket) 380g

www.smartpark.net
For our full range of driver
assistance and safety products:
Reversing Sensors LCD Mirror
Monitors
LCD4WM
Commercial
Camera Systems
Factory Display
Integration Units
iConnect™ iPod
integration
GM Bracket
Camera
HitchView Bumper
Camera
Passenger Vehicle
Camera