Smartec STC-IPM3542A/1 User manual

1.3 Megapixel
WDR IP Camera
STC-IPM3542A/1
Thanks for purchasing our product. Before operating the unit, please read the
instructions carefully and keep this manual for future reference.

120621-XE3243EO-0831-V2.1-V2a
i
Safety Warning
1. Read this manual carefully before installing the unit
Please read this manual first for correct installation and operation.
2. Never install the camera on a ceiling that cannot hold its weight
The product may fall down and cause damages.
3. Never install the camera near electric or magnetic fields
Install the camera away from TV, radio transmitter, magnet, electric motor, transformer, audio
speakers since the magnetic fields generate from above devices would distort the video image.
4. Never install or use the camera in areas exposed to water, oil or gas
The water, oil or gas may result in operation failure, electric shock or fire. Do not use this unit
near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet
basement, near a swimming pool, in an unprotected outdoor installation, or any area which is
classified as a wet location.
5. Never face the camera toward the sun
Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit.
6. Power Cord Protection
Touching the wet power cord with hands or touching the power cord with wet hands may result in
electric shock. Power supply cords should be routed so that they are not likely to be walked on
or pinched by items placed upon or against them, playing particular attention to cords and plugs,
convenience receptacles, and the point where they exit from the appliance.
7. Attachments
Do not use attachment not recommended by the product manufacturer as they may cause
hazards.
8. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of
any kind onto the product.
9. Do not operate the camera in environments where the temperature,
humidity or power source is beyond the specified ones
Use the camera in suitable environments where the temperature is within -10°C~50°C and
humidity below 80%. Use the input power source as this instruction indicated.

120621-XE3243EO-0831-V2.1-V2a
ii
10. Cleaning
Unplug the unit from the outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
11. Never disassemble the camera nor put impurities in it
Disassembly or impurities may result in trouble or fire.
12. Stop using when the product emits smoke or abnormal heat
13. Servicing
Do not attempt to repair this unit yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
14. Retain Instructions
THE SAFETY AND OPERATING INSTRUCTIONS SHOULD BE RETAINED FOR FUTURE
REFERENCE.
NOTE:
The information in this manual was current when published. The manufacturer reserves the right to
revise and improve its products. All specifications are therefore subject to change without notice.

120621-XE3243EO-0831-V2.1-V2a
iii
Table of Contents
1. CAMERA................................................................................................................................................................................ 1
1.1 FEATURE........................................................................................................................................................................... 1
1.2 LIST OF CONTENTS ............................................................................................................................................................ 1
1.3 SYSTEM REQUIREMENTS.................................................................................................................................................... 1
1.4 SPECIFICATION .................................................................................................................................................................. 2
1.5 DIMENSIONS...................................................................................................................................................................... 3
1.6 CAMERA OVERVIEW........................................................................................................................................................... 4
1.7 INSTALLATION .................................................................................................................................................................... 5
2. USER INTERFACE ................................................................................................................................................................ 7
2.1 LOGIN ............................................................................................................................................................................... 7
2.2 INTERFACE OVERVIEW ....................................................................................................................................................... 8
1. Live View ............................................................................................................................................................... 9
2. Video ................................................................................................................................................................... 10
3. Image .................................................................................................................................................................. 12
4. Audio ................................................................................................................................................................... 14
5. DateTime............................................................................................................................................................. 15
6. Network ............................................................................................................................................................... 16
7. Alarm................................................................................................................................................................... 17
8. Storage................................................................................................................................................................ 18
9. Maintain............................................................................................................................................................... 19
10. PTZ/OSD............................................................................................................................................................. 20

120621-XE3243EO-0831-V2.1-V2a
1
1. CAMERA
1.1 Feature
Sony 1 / 3" 1.3 Megapixel Progressive Exmor™ CMOS Sensor
1280(H)x1024(V) (SXGA); H.264, MPEG4, M-JPEG
Color:[email protected], B/W:[email protected], Sense-up:[email protected]
2D Noise Reduction & Sense Up
Motion Detection & Alarm Trigger
Two-way Audio & Support Multicast
Support Micro SD/SDHC Card
Support 12Vdc / PoE Power Input
Support ONVIF
1.2 List of Contents
Camera Unit
User manual
Accessories (Vary by model)
1.3 System Requirements
For IE Browser Live View--
Resolution
1280x720p
1280x1024p
1920x1080p
2056x1536p(3.0MP)
Suggested Bitrate
2000~4000kbps
2000~6000kbps
4000~8000kbps
4000~10000kbps
Compression format
H264 or MPEG4
H264 or MPEG4
H264 or MPEG4
H264 or MPEG4
Frame Rate
Up to 30fps
Up to 30fps
Up to 30fps
Up to 20fps
CPU (Recommended)
Intel Core i3 540
Intel Core i3 540
Intel Core i5 760
Intel Core i7 860
RAM
2GB RAM
2GB RAM
4GB RAM
4GB RAM
IE Browser
8.0 or above
8.0 or above
8.0 or above
8.0 or above
OS
WinXP-Pro
WinXP-Pro
WinXP-Pro/Win7 Pro
WinXP-Pro/Win7 Pro
Microsoft Internet Explorer 8.0 or above(Only support 32bit IE Browser)
The compression format of IP Cam encoder is in H.264/High profile.
When using Live view in IE Browser, IP Cam will decode in real time by RTSP, the maximum
bitrate is 10,000kps.

120621-XE3243EO-0831-V2.1-V2a
2
1.4 Specification
VIDEO
Image Sensor
Sony 1 / 3" 1.3 Megapixel Progressive Exmor™ CMOS Sensor
Highest Resolution
1280(H)x1024(V) (SXGA)
Video Resolution
1280x960, 1280x720, 720x480
Video Frame Rate
Up to 30fps for All Video
Video Compression
H.264, MPEG4, M-JPEG
Minimum Illumination
Color:[email protected], B/W:0.01Lux@F1.2, Sense-up:[email protected]
Digital Wide Dynamic Range
10 Level (Adjustable Level Settings)
Second Video Output
1.0Vp-p Composite, 75Ω (BNC)
Signal to Noise Ratio
More than 52dB (AGC off)
FUNCTION
Menu
Can Be Set via Browser
Digital Day&Night Mode
Color / B&W / Auto
Auto Electronic Shutter
1/2 to 1/100,000 sec.
Manual Electronic Shutter
1/2, 1/4, 1/8, 1/15, 1/30, 1/60, 1/120, 1/250, 1/500, 1/750, 1/1,000,
1/1,500, 1/2,000, 1/10,000, 1/100,000 sec.
White Balance
Auto_wide / Auto_normal / Sunny / Shadow / Indoor / Lamp / FL1 / FL2
Dynamic Noise Reduction
2D DNR
Sense Up
Yes
Language
English / Japanese / Traditional Chinese / Simplified Chinese
Image Setting
Brightness / Contrast / Saturation / Sharpness / DeNoise /
EV Compensation / AWB / WDR / Rotation
Motion Detection
Yes
Motion Alarm Trigger
Yes
Timer Clock
Yes
Camera Control Interface
Pelco D, Pelco P, Customer
NETWORK
Browser
IE 8.0 or Above
Ethernet
10/100M Auto Negotiation
Bit Rate Transmission
64 up to 12,000 Kbps
Supported Protocols
TCP, UDP, HTTP, SMTP, FTP, NTP, DNS, DHCP, ARP, UPnP, RTSP
RTP Ethernet (RJ-45 Wired 10/100 Base-TX)
Video Streaming
H.264, MPEG4 and M-JPEG Dual/Triple Streaming
Audio Streaming
Two-way Audio ; G.711 (μLaw), 8KHz Sample Rate
Users
Support 10 Simultaneous Users
Security
ID/Password Protection, IP Address Filtering, User Access Log
Alarm Event
File Upload via FTP and Email/Notification via Email, HTTP, External
Digital Output Activation, micro SD Recording
Multicast
Support Multicast Function
GENERAL
Connector
Audio, RJ45/PoE, DC Power, BNC (Composite Video Out),
DI/DO/RS485, Micro SD Slot
Automatic IRIS ; Connector
DC
Lens Mount
Built-in DC Auto IRIS Lens
Lens, Angle of View (H)
f3.0~10mm/F1.3 Aspherical Megapixel Varifocal Lens/95.6°~28.8°
Water Resistance
IP66
Max. Breaking Strength
656.1 Kgf
Power Supply ; Consumption
12Vdc / PoE ; 4W, Heater adds max.3W
Operation ; Storage Temp.
-40°C ~ 50°C ; -20°C ~ 60°C
Operation ; Storage Humidity
Maximum: RH80% ; RH90%
Dimensions
142(DIA)x112(H)mm
Net Weight
950g
Subject to change without notice

120621-XE3243EO-0831-V2.1-V2a
3
1.5 Dimensions

120621-XE3243EO-0831-V2.1-V2a
4
1.6 Camera Overview
1. Switches & Connectors
■ DI / DO Port:
(1) IO
(2) IO
(3) ALM-RST (Alarm Reset): The system will force the alarm input to cancel.
(4) ALM-IN (Alarm Input): When activate, the alarm input will be triggered.
(You may also set the alarm to input while the DAY/NIGHT Mode is activated.)
(5) ALM-OUT (Alarm Output): When activate, the alarm output will be triggered.
(You may also set the alarm to output while the DAY/NIGHT Mode is activated.)
(6) GND (Ground)
(7) RS-485(－) Output: Controlled by RS-485 signal sent by the network part (NEGATIVE)
(8) RS-485(＋) Input: Controlled by RS-485 signal sent by the network part (POSTIVE)
■Heater:
This heater will keep the lens and glass free of obscuring condensation. The built-in thermostat
switches the heater on and off appropriately.
Audio Out
Reset Switch
LAN / PoE (RJ-45)
Power 12V DC
Heater
Audio In
DI / DO
Video Out

120621-XE3243EO-0831-V2.1-V2a
5
1.7 Installation
1. Installation Flow Chart
Default Settings of IP CAM
IP Address: 192.168.1.168
User Name: admin
Password: 9999
Suggested IP Address For PC/NB
IP Address: 192.168.1.200
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1
START
Power Type
FINISH
DC
Check the power of PoE
Plug the Power Adapter
Connect the RJ-45 LAN cable to the IP CAM
Get into the IP CAM setting window
PoE
IP setting for PC/NB
(Please see the suggested IP address)
Disable the anti-virus software and firewall
Turn on the PC/NB and log-in Windows OS
Run IE browser (IE 8.0 or above)
User Name: admin / Password: 9999
Type the URL http://192.168.1.168
and get into IP CAM setting window

120621-XE3243EO-0831-V2.1-V2a
6
2. Direct Link
Make sure PC installed with JAVA Version 6 Update 30 or above
(1) Plug the power adapter to IP CAM.
(2) Run the IE browser with http://192.168.1.168
(3) When the log-in window pop-up, please input the User Name and Password.
(4) Whenever the connection is ready, the main page (setting window) of IP CAM will show on.
3. Link via Hub / PoE Hub
Make sure PC installed with JAVA Version 6 Update 30 or above
(1) Run the IE browser with http://192.168.1.168
(2) When the log-in window pop-up, please input the User Name and Password.
(3) Whenever the connection is ready, the main page (setting window) of IP CAM will show on.
Adapter
DC12V
Cat-5 LAN cable
PoE / Hub
Cat-5 LAN cable
Cat-5 LAN cable

120621-XE3243EO-0831-V2.1-V2a
7
2. USER INTERFACE
2.1 Login
1. Start the browser, and input http://192.168.1.168/ in the address field, then press Enter.
2. Enter User Name and Password In the prompt window, and click OK.
The default User Name and Password is admin and 9999. You will need to enter the account and password
every time whenever you restart the application or reconnect.

120621-XE3243EO-0831-V2.1-V2a
8
2.2 Interface Overview
After login to the system, the screen will be displayed as below:
There are many function buttons on the left side. They are as the table below. All of the function buttons
and its details will be shown on the following sections.
Live View
Video
Image
Audio
DateTime
Network
Alarm
Storage
Maintain
PTZ/OSD

120621-XE3243EO-0831-V2.1-V2a
9
1. Live View
Main page. Display the image captured by the camera.
Language:
English / 日本語(Japanese) / 繁中(Traditional Chinese) /
簡中(Simplified Chinese) (Vary by area)
Full Screen
Snapshot
Record & Save
Stop Recording
Information
Motion Detect
Upload
Audio On
Audio Off
Zoom in
Zoom out
Restore

120621-XE3243EO-0831-V2.1-V2a
10
2. Video
IP (Internet Protocol) video settings of the camera. Modify the settings of IP stream type,
streams and local display.
NOTE:
Once the change completed, click Submit to save the settings.
Stream Type
Video Streams
Single / Dual / Tri-stream
Codec Profiles
H.264 + MPEG4 + MegaPixel JPEG
Resolution
H.264: 720P, H.264: D1, H.264: SXGA, H.264:1080P, H.264:
3M
(NOTE: The content may vary by models)

120621-XE3243EO-0831-V2.1-V2a
11
H.264
Frame rate
1 / 3 / 5 / 10 / 15 / 20 / 25 / 30 fps
Bitrate
4000 Kbps
Rate Control
OFF / VBR / CBR
Local Display
Local Display
OFF / NTSC / PAL / HD720P
Rotation
OFF / HORIZONTAL / VERTICAL / BOTH
Format
H.264 (1920 x 1080)
Size
5 sec / 10 sec
Shutter Speed (Min)(Second)
1/2, 1/4, 1/8, 1/15, 1/30, 1/60, 1/120, 1/250, 1/500, 1/750,
1/1000, 1/1500, 1/2000, 1/10000, 1/100000
Shutter Speed (Max)(Second)
1/30, 1/60, 1/120, 1/250, 1/500, 1/750, 1/1000, 1/1500,
1/2000, 1/10000, 1/100000
Shutter Speed (Level)
0~7
Quality (Level)
0~7
FixedShutter (Second)
1/2, 1/4, 1/8, 1/15, 1/30, 1/60, 1/120, 1/250, 1/500, 1/750,
1/1000, 1/1500, 1/2000, 1/10000, 1/100000
FixedShutter (Level)
0~7
(NOTE: The content may vary by models)

120621-XE3243EO-0831-V2.1-V2a
12
3. Image
Modify the settings of image, OSD and advanced image settings.
Image
Brightness
0 ~ 255 (Default 128)
Contrast
0 ~ 255 (Default 128)
Saturation
0 ~ 255 (Default 128)
Sharpness
0 ~ 255 (Default 128)
DeNoise
0 ~ 255 (Default 128)
EV Compensation
0 ~ 255 (Default 128)
Load Default
Restore to the default values
Stream1 / Stream2 / Stream3 OSD
Mode
Date / Time / Text
Text Position
Top-Left / Top-Right

120621-XE3243EO-0831-V2.1-V2a
13
Advanced Settings
Auto IRIS
Manual / Auto
Flicker Control
60hz NTSC / 50hz PAL
White Balance
AUTO_WIDE / AUTO_NORMAL / SUNNY / SHADOW /
INDOOR / LAMP / FL1 / FL2
Back Light Compensation
Off / On
Back Light Level
Min / Mid / Max
WDR Enhancement
Off / On
WDR Level
0~7
IR-Cut Setting
Auto / BW / Color / External
(NOTE: The content may vary by models)

120621-XE3243EO-0831-V2.1-V2a
14
4. Audio
Modify the settings of audio.
Audio
Enable Audio
Enable / Disable
Audio Mode
MIC / SPEAKER / BOTH
Input volume
0~100
Sample Rate
8KHz / 16KHz
Bitrate
Auto / 64Kbps
Output Volume
0~100
(NOTE: The content may vary by models)

120621-XE3243EO-0831-V2.1-V2a
15
5. DateTime
Modify the settings of date and time.
DateTime
Set Manual Date
Manual set the date and time
Sync Current PC Date
Synchronization the date and time with current PC
Sync with SNTP Server
Synchronization the date and time with SNTP Server
Date Format / Position
Select the format and position of date
Time Format / Position
Select the format and position of time

120621-XE3243EO-0831-V2.1-V2a
16
6. Network
Modify the settings of network and IP address.
DHCP
Use DHCP
Use DHCP for connection
Static IP
Use static IP for connection
PPPoE
Use PPPoE for connection
Multicast
Enable Multicast
Enable / Disable
H264 Main /Sub Port
Communication port for H.264
MPEG4 Main / Sub Port
Communication port for MPEG4
MJPEG Port
Communication port for M-JPEG
SMTP
SMTP Auth
Enable / Disable SMTP authentication
FTP Server
FTP Server
Domain name of FTP server
DDNS Server
DDNS Server
Domain name of DDNS server
SNTP Server
SNTP Server
Domain name of SNTP server