Smart+ Products SPP-1500-4PR User manual

SMART+ PRODUCTS
Infrared Heater
User’s Manual
Model# SPP-1500-4PR
120VAC 15 AMP DEDICATED CIRCUIT
FOR INDOOR USE ONLY
The SMART+
PRODUCTS Infrared
Heater works with your
in‐home furnace to provide
supplement
heat. Carefully and
thoroughly read this
manual before using the
SMART+ PRODUCTS
Infrared Heater for the
first time. We
recommend keeping this
manual for regular
review and future
reference. Heater is
intended for residential
use.

Thank you for choosing a SMART+ PRODUCTS Infrared Zone Heating System. This owner’s manual will provide you
with valuable information necessary for the proper care and maintenance of your new product. Please take a few moments
to thoroughly read the instructions and familiarize yourself with all the operational aspects of your new heater.
IMPORTANT INSTRUCTIONS
When using this electric unit, basic safety precautions should always be followed to reduce the risk of fire, electric
shock, and injury to persons, including the following:
1Read ALL instructions before using this unit.
2CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater yourself.
3This heater may get hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use
handles when moving this heater.
4Keep combustible materials, such as furniture, pillows, bedding, paper, clothes, and curtains at least 3 ft from the
front of the heater and keep them away from the sides, top, and rear. DO NOT place towels or other objects on the heater.
5Extreme caution is necessary when any heater is used by or near children or the disabled, or when the heater is left
operating and unattended.
6DO NOT operate any heater with a damaged cord or after the heater malfunctions, has been dropped or damaged
in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
7This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER locate heater
where it may fall into a bathtub or other water container. To protect against electrical hazards, DO NOT immerse in water
or other liquids.
8DO NOT touch the control panel or plug with a wet hand.
9DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar coverings. Arrange
cord away from traffic area and where it will not be tripped over.
10 DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric
shock or fire, or damage the heater.
11 To prevent a possible fire, DO NOT block the air intakes or exhaust in any manner. DO NOT use on soft surfaces,
like a bed, where openings may become blocked.
12 A heater has hot and arcing or sparking parts inside. DO NOT use in areas where gasoline, paint, explosive and/or
flammable liquids are used or stored. Keep unit away from heated surfaces and open flames.
13 Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if
you have to use an extension cord, the cord shall be No. 16 AWG minimum size and rated not less than 1500W.
14 To avoid fire or shock hazard, plug the unit directly into a 120 V AC electrical outlet.
15 To disconnect heater, turn controls to OFF, then remove plug from outlet. Pull firmly on the plug, DO NOT unplug
by pulling on the cord.
16 Always unplug the unit before moving or cleaning, or whenever the heater is not in use.
17 Use only for intended household use as described in this manual. Any other use not recommended by the
manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by
unauthorized dealers may cause hazards.
18 Always use on a dry, level surface. Use on floor only.
19 DO NOT use outdoors.
20 WARNING: To reduce the risk of fire or electric shock, DO NOT use this unit with any solid-state speed control
device.
21 DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your
warranty. The inside of the unit contains no user serviceable parts. Qualified personnel should perform all servicing only.
22 Connect to properly grounded outlets only.
23 .Save these instructions.

SPECIFICATIONS
SAFETY FEATURES
Tip-Over Safety Feature
This heater is equipped with a tip-over safety feature. Once the heater is tipped over, an internal switch will automatically
shut the heater off. Once the heater is restored an upright position, the heater will reset. To continue operation, turn on the
heater using the supplied remote control or the control panel on the heater.
Overheat Safety Feature
This heater is equipped with a overheat safety feature. When the heaters internal components reach a certain
temperature that could cause overheat and possible fire, the heater will automatically shut off.
Voltage Rating
120 V (60Hz)
Power Consumption
1000/1500W
Unit Size
13.1 in. (W) x 16.5 in. (D) x 16.7 in. (H)
Unit Weight
22.7 lbs
Or
Turn the heater on by pressing the ON/OFF button on the
control panel or by pressing the Power button on the
supplied remote control.

WARNING: This heater has a voltage rating of 120 volts. The cord has a plug as shown in A. An adapter as shown in C is
available for connecting three-blade grounding-type plugs to
two-slot receptacles. The grounding lug extending from the
adapter must be connected to a permanent ground such as a
properly grounded outlet box. The adapter should not be used
if a three-slot grounded receptacle is available.
DO NOT DEFEAT THE SAFETY PURPOSE OF THE
GROUNDED PLUG.
WARNING: It is normal for the power cord to feel warm to
the touch; however, a loose fit between the outlet and the plug
may cause overheating of the plug. If this occurs, try inserting the plug into a different outlet. Contact a qualified
electrician to inspect the original outlet for damage.
IN THE BOX
·INFRARED ZONE HEATING SYSTEM ·REMOTE CONTROL ·REMOTE CONTROL BATTERY
·INSTRUCTION BOOKLET
PRODUCT DIAGRAM
Remote Control

Control Panel
1
2
3 4
1211109 8 7 6 5
1、Signal-receiving window: for receiving remote
control signal. 2、Digital display：indicate set
room temperature or time value according to the
timer. 3、Power indication Light：indicate when
the unit connects to power supply. 4、ON/OFF
switch button: for power-on or off. 5、Energy-
saving mode：The light ‘s on when energy-saving
mode goes. 6、Mode button：for select running
mode. 7、Heat-down mode indication light: The
light ‘s on when heat-down mode goes. 8、Temp up
button: for setting temp upward. 9、Heat-up mode
indication light: The light ‘s on when heat-up mode
goes. 10、Temp down button: for setting temp
downward. 11、Timer indication light：The light’s
on when timer functions. 12、Timer button：used for setting the timer and adjust time value for the timer.
13、Fahrenheit indicating light 14、C/F Button (Button for alternating between Fahrenheit and Celsius). 15、Celsius
indicating light

Remote Control
Mode button: Used for mode selection ON/OFF button: Used for power-
on or power-off Temp up button: to make set temperature raise
Temp down button: to make set temperature ecline
Timer button: used for setting timer and adjust time value of timing
PREPARATION
Place the heater on a firm, level surface and plug into a grounded 120V 60Hz power outlet. and turn on the power switch
in the rear of the unit. Only operate heater in upright position with caster wheels attached.
When using remote control, please pull out the insulating film as the following steps.
Remote control Insulating film Battery cover

OPERATING INSTRUCTIONS 1、Start and select working mode
2、Setting room temperature
Voltage Rating
120 V (60Hz)
Power Consumption
1000/1500W
Unit Size
13.1 in. (W) x 16.5 in. (D) x 16.7 in. (H)
Unit Weight
22.7 lbs
Or
Turn the heater on by pressing the ON/OFF button on the
control panel or by pressing the Power button on the
supplied remote control.
Or
Select a heat setting. Press the MODE button to toggle
between the three heat settings.
Power for heat-up mode is 1500W; and heat-down is
1000W. ECO mode is an Economic Energy Saving
Function. When ECO mode is chosen the heater will
consume one-third less power once the room temperature
reaches a certain point.
Voltage Rating
120 V (60Hz)
Power Consumption
1000/1500W
Unit Size
13.1 in. (W) x 16.5 in. (D) x 16.7 in. (H)
Unit Weight
22.7 lbs
Or
Turn the heater on by pressing the ON/OFF button on the
control panel or by pressing the Power button on the
supplied remote control.
Or
Select a heat setting. Press the MODE button to toggle
between the three heat settings.
Power for heat-up mode is 1500W; and heat-down is
1000W. ECO mode is an Economic Energy Saving
Function. When ECO mode is chosen the heater will
consume one-third less power once the room temperature
reaches a certain point.
Or Or Or
Adjust the thermostat by pressing the arrows on the control
panel or remote control.
Or
Set temperature indication varies from 86℉to 59℉，or
from 30℃to 15℃. Once you have chosen the desired
temperature, the heater will remain on until the room
temperature increases to the temperature on the digital
display. The heater will cycle on and off to maintain the
desired room temperature.
Press ℃/℉button, then digital display will indicate
Fahrenheit value or Celsius value.

3、Setting timer-power-off
Caution!
ONLY
under
power-on
mode can
you set
timer-
power-off
function.
4、Setting
timer-power-
on
Caution! ONLY under power-off mode can you set timer-power-on function.
5、Setting electro lock
Function of electro lock can avoid misoperation from children. Locking can be set in both power-on and power-off
modes.
Voltage Rating
120 V (60Hz)
Power Consumption
1000/1500W
Unit Size
13.1 in. (W) x 16.5 in. (D) x 16.7 in. (H)
Unit Weight
22.7 lbs
Or
Turn the heater on by pressing the ON/OFF button on the
control panel or by pressing the Power button on the
supplied remote control.
Or
Select a heat setting. Press the MODE button to toggle
between the three heat settings.
Power for heat-up mode is 1500W; and heat-down is
1000W. ECO mode is an Economic Energy Saving
Function. When ECO mode is chosen the heater will
consume one-third less power once the room temperature
reaches a certain point.
Voltage Rating
120 V (60Hz)
Power Consumption
1000/1500W
Unit Size
13.1 in. (W) x 16.5 in. (D) x 16.7 in. (H)
Unit Weight
22.7 lbs
Or
Turn the heater on by pressing the ON/OFF button on the
control panel or by pressing the Power button on the
supplied remote control.
Or
Select a heat setting. Press the MODE button to toggle
between the three heat settings.
Power for heat-up mode is 1500W; and heat-down is
1000W. ECO mode is an Economic Energy Saving
Function. When ECO mode is chosen the heater will
consume one-third less power once the room temperature
reaches a certain point.
Voltage Rating
120 V (60Hz)
Power Consumption
1000/1500W
Unit Size
13.1 in. (W) x 16.5 in. (D) x 16.7 in. (H)
Unit Weight
22.7 lbs
Or
Turn the heater on by pressing the ON/OFF button on the
control panel or by pressing the Power button on the
supplied remote control.
Or
Select a heat setting. Press the MODE button to toggle
between the three heat settings.

MAINTENANCE
1Turn off the power switch in the rear of the unit.
2Unplug the unit and let it cool completely.
3To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. You may use a mild detergent if
necessary. After cleaning, dry the unit with a soft cloth. CAUTION: DO NOT letliquid enter the heater.
4DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes to clean the heater. This may
cause damage or deterioration to the surface of the heater.
5DO NOT immerse the heater in water.
6Wait until the unit is completely dry before use.
7Air filter needs cleaning after used 3 months. Please take down the filter as following steps. Flushand clean the
taken –down filter with water ,then dry it out and re-assemble.
8If won’t use the unit for a long time, please take out battery in remote control according to following steps, then
take care of the remote control.
Remote control Battery cover Battery

STORAGE
Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use the original packaging to
repack the unit.
TROUBLESHOOTING
If the heater will not operate, please check the following before seeking repair of service:
1. Check if the power cord is plugged into an electrical outlet, if not, plug in.
2. Check if electricity to the main fuse is working.
3. Check if the battery in remote control is in good use ,and if the insulating film is pulled out.
NOTE: The heater may not be operating if the thermostat is set higher than the room temperature. To begin
operation, increase the thermostat temperature for a higher heat setting.