Smart+ Products SPP1500SBH User manual

DIGITAL QUARTZ INFRARED HEATER
OWNER’S MANUAL
Model No.: SPP1500SBH
PLEASE SAVE THESE INSTRUCTIONS
WARNING: READ THIS OWNER’S MANUAL CAREFULLY BEFORE USE

Thank you for choosing the Smart+ Products Digital Quartz Infrared Heater. This owner’s manual
will provide you with valuable information necessary for the proper care and maintenance of your
new product. Please take a few moments to thoroughly read the instructions and familiarize
yourself with all the operational aspects of your new heater.
IMPORTANT INSTRUCTIONS
When using this electric unit, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to
persons, including the following:
1. Read ALL instructions before using this unit.
2. CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater yourself.
3. This heater may get hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles
when moving this heater.
4. Keep combustible materials, such as furniture, pillows, bedding, paper, clothes, and curtains at least 3 ft from the front of
the heater and keep them away from the side, top, and rear. DO NOT place towels or other objects on the heater.
5. Do not leave heater unattended while on. Extreme caution is necessary when any heater/fan is used by or near children or
invalids and whenever the heater/fan is left operating unattended.
6. DO NOT operate any heater with a damaged cord or after the heater malfunctions, has been dropped or damaged in any
manner. Return heater to authorized service facility for examination, electrical mechanical adjustment, or repair
7. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER locate heater where it
may fall into a bathtub or other water container. To protect against electrical hazards, DO NOT immerse in water or other liquids.
8. DO NOT touch the control panel or plug with a wet hand.
9. DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar coverings. Arrange cord away
from traffic area and where it will not be tripped over.
10. DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire,
or damage the heater.
11. To prevent a possible fire, DO NOT block the air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed,
where openings may become blocked.
12. A heater has hot and arcing or sparking parts inside. DO NOT use in areas where gasoline, paint, explosive and/or flammable
liquids are used or stored. Keep unit away from heated surfaces and open flames.
13. Do not use an extension cord because the extension cord may overheat and cause a risk of fire.
14. To avoid fire or shock hazard, plug the directly remove plug form outlet. Pull firmly on the plug, DO NOT unplug by pulling
on the cord.
16. Always unplug the unit before moving or cleaning, or whenever the heater is not in use.
17. Use only for intended household use as described in this manual. Any other use not recommended by the manufacturer may
cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by unauthorized dealers may
cause hazards.
18. Always use on a dry, level surface. Use on floor only.
19. DO NOT use outdoors.
20. WARNING: To reduce the risk of fire or electrical shock, DO NOT use this unit with any solid-state speed control device.
21. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The
inside of the unit contains no user serviceable parts. Qualified personnel should perform all servicing only.
22. Connect to properly grounded outlets only.
23. SAVE THESE INSTRUCTIONS.

SPECIFICATIONS
Voltage Rating
Power Consumption
Unit Size
Unit Weight
SAFETY FEATURES
Tip-Over Safety Feature
120 V (60Hz)
1000/1500W (12.5 Amps), 5120 BTUs
325x190x314mm / 12.8x7.5x12.4 inches
5.2kgs / 11.5lbs
This heater is equipped with a tip-over safety feature. Once the heater is tipped over, an internal switch will automatically shut the
heater off. Once the heater is restored an upright position, the heater will rest. To continue operation, turn on the heater using the
supplied remote control or the control panel on the heater.
Overheat Safety Feature
This heater is equipped with an overheat safety feature. When the heaters internal components reach a certain temperature that could
cause overheating and possible fire, the heater will automatically shut off. To reset the heater simply turn the unit off, unplug the heater
for about 10 minutes. Plug in and turn it on.
WARNING: This heater has a voltage rating of
120 volts. The cord has a plug as shown in A. An
adapter as shown in C is available for connecting
three-blade grounding-type plugs to two-slot
receptacles. The grounding lug extending from the
adapter must be connected to a permanent ground
such as a properly grounded outlet box. The
adapter should not be used if a three-slot grounded
receptacle is available.
DO NOT DEFEAT THE SAFETY PURPOSE OF
THE GROUNDED PLUG
WARNING: It is normal for the power cord to feel warm to the touch; however, a loose fit between the outlet and the plug may cause
overheating of the plug. If this occurs, try inserting the plug into a different outlet.
Contact a qualified electrician to inspect the original outlet for damage.

PRODUCT DIAGRAM
Remote control hider
Plastic Cabinet
Control Panel
Air Outlet
Air Intake
Temperature sensor
Power Switch
Control Panel
15
14
1
3
5
6
9
12
13
11
10
2
4
7
8

1、Fahrenheit / Celsius Indicator: indicates when Fahrenheit / Celsius mode is on.
2、Lock Indicator: indicates when Lock mode is on.
3、Digital display: Normal ambient temperature display, temperature control and display flashing when regulating the temperature shut
down when the track 60 seconds countdown, timer time display 1-12H, a sleep timer and alarm function to POWER.
4、Remote Indicator: indicates when Remote mode is on
5、Energy-Saving Function Indicator: indicates when energy-saving mode is on.
6、Timing Display Indicator: indicates when Timing Display mode is on
7、High Power Indicator: indicates when high 1500 watt mode is on.
8、Low Power Indicator: indicates when low 1000 watt mode is on
9、Mode Button: use for selecting running mode, high power, low power or energy-saver
10、Up Button: used for raising set temperature and timer duration.
11、Down Button: used for reducing set temperature and timer duration.
12、Timer Power-On/Off Button: used for turning timer function on or off.
13、Control Panel Lock Button: Press 2 seconds to lock, it locks all keys and indicator lights, in addition to lock indicator light, other
indicator lights and display screen are in dark, and can ensure the normal working condition, press 2 seconds to unlock
14、Fahrenheit / Celsius Button:
15、On/Off Button: turns heater on or off.
Remote Control
The remote control buttons function the same way as they do on the control panel.

PREPARATION
Place the heater on a firm, level surface and plug into a grounded 120V 60Hz power outlet. Only operate this heater
in upright position with feet attached.
When using remote control, please pull out the clear insulating film to activate the battery as shown below.
MAINTENANCE
1. Unplug the unit and let it cool completely.
2. To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. You may use a mild detergent if necessary.
After cleaning, dry the unit with a soft cloth. CAUTION: DO NOT let liquid enter the heater.
3. DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes to clean the heater. This may cause
damage or deteriorate the surface of the heater.
4. DO NOT immerse the heater in water.
5. Wait until the unit is completely dry before use.
6. Clean the air filter after 3 months of use or when the filter appears to be dirty. The below diagram shows the location of the
air filter. Remove the Air Intake Grille by pulling handle down and outwards. Wash the filter with clean water. Allow filter to
completely dry before reassembling back onto the heater

7. If you do not plan on using the heater for a long period of time, please remove the remote control battery according to the
below diagram.
STORAGE
Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use the original packaging to repack the unit.
TROUBLESHOOTING
If the heater will not operate, please check the following before seeking repair or service:
1. Check if the power cord is plugged into an electrical outlet, if not, plug in.
2. Check if there is power to the outlet.
3. Check if the battery in remote control is good and that the battery insulating film is pulled out (see
remote preparation on page 6 of this manual).
NOTE: The heater may not operate if the thermostat is set higher than the ambient room temperature. To
begin operation, increase the thermostat temperature setting on the heater using the control panel buttons
or remote control buttons.
Smart+ Products –New Holland, PA
www.smartplusproducts.com