SmartPool S120U User manual

www.smartpool.com
®
INSTALLATION AND OPERATION MAN AL
Models S120U & S240U
Read all instructions before assembling or using the Sun eater system.
Retain this manual for future use.

www.smartpool.com 2
TABLE OF CONTENTS
Important Safety Information...........................................................................................................................................2
ow SUN EATER Works....................................................................................................................................................3
Sizing Guide ....................................................................................................................................................................3
List of Components...........................................................................................................................................................3
Installation of Sun eater/Layout Options......................................................................................................................4-6
Winterization...................................................................................................................................................................7
Repairs............................................................................................................................................................................7
Available Kits/Accessories ................................................................................................................................................7
Troubleshooting ...............................................................................................................................................................8
Warranty.........................................................................................................................................................................8
IMPORTANT SAFETY INFORMATION
Please read this manual carefully and thoroughly. Improper installation or failure to comply with the guidelines of this manual
may damage the product and will void the warranty.
It is advised to consult with a professional when installing the Sun eater on a roof, fence or rack system.
When installing the collectors near the pool, especially on an elevated rack system, ensure that the structure does not provide
access to the pool.
Installing the collectors over grass will cause damage to the lawn.
Do not walk on the collectors.
Turn off all pool equipment prior to installation.
Only use SmartPool approved mounting equipment when installing collectors on a roof, fence or rack system.
Wear and tear components (connector hoses, strapping, clamps, plastic fittings and hardware) should be inspected regularly to
ensure they are in working condition. These components are not covered by warranty.
!
CAUTION:
!
CAUTION:
!
CAUTION:
!
CAUTION:
!
CAUTION:
!
CAUTION:
!
CAUTION:

www.smartpool.com3
HOW S NHEATER WORKS
• The pool pump circulates the
water through the collectors.
• The collectors absorb the heat
from the sun.
• Warm water is returned to
the pool.
SUN EATER collectors have a web construction designed for
maximum heat absorption regardless of the position of the sun.
Collector Cross Section
SIZING G IDES
ABOVEGRO ND POOLS
Round Oval S140 S240
Up to 24' Up to 15' x 30' 1 Box 1 Box*
Up to 33' Up to 21' x 41' 2 Boxes 1 Box
*The S240U can be used but only a S140U is required.
INGRO ND POOLS
Dimensions S140 S240 Kits
Up to 15' x 30' 4 Boxes 2 Boxes 1 SK22U
Up to 16' x 36' 6 Boxes 3 Boxes 1 SK22U
Up to 20' x 40' 8 Boxes 4 Boxes 1 SK22U
S120
Item Description Qty
A1.5" Stainless Steel ose Clamp 4
B3.75" Rubber ose Connector 1
CPVC Elbow Connector 2
DPVC End Cap 2
ETeflon Tape 1
S240
Item Description Qty
A1.5" Stainless Steel ose Clamp 4
B3.75" Rubber ose Connector 2
CPVC Elbow Connector 2
DPVC End Cap 4
ETeflon Tape 1
Note: An extra rubber hose has been supplied to connect
additional Sun eater systems.
A
(x4) B
C
(x2)
D
(x2)
E
INSTALLATION
TOOLS REQUIRED
• Flathead screwdriver or 5/16” (8mm) nut driver
• Plug for return fitting
• For roof or rack mounting:
o Power drill
o 1/8” (3mm) drill bit
o #2 Phillips head drill bit
o Silicone sealant (GEII or equivalent)
GUIDELINES FOR POSITIONING T E COLLECTOR
• The collector(s) needs at least 6 hours of full sunlight daily.
• For ground installation, ensure the area is free of sharp objects prior
to installation.
• A 1hp pump will handle installations up to 30ft from the pool
equipment and a height of 1 story.
•
The collector(s) can be installed on the ground, a roof, a rack or a fence.
Additional plumbing and hardware kits may be required (not included).
READ T E ENTIRE MANUAL PRIOR TO T E INSTALLATION AND USE OF T E SUN EATER SYSTEM.
LIST OF COMPONENTS

www.smartpool.com 4
S140 INSTALLATION
This layout is for a single collector installed near the pool filter equipment. Installing the collector on a roof, rack or fence may require additional
plumbing and hardware kits.
Cool Water
(Feed)
War Water
(Return Fitting)
Pool Pu p
Elbow Connector
Elbow Connector
White End Cap
White End Cap
Label
Filter
Feed Hose
Return Hose
1) Ensure there is adequate work space to unroll the 20’ collector.
2) Remove the collector from the box and the strap from around the
collector. Slowly uncoil the panel.
Note: Laying the collector in the reverse direction of the coils will help
flatten the panel.
3) Remove and discard the black protective caps covering the threaded
portion of the headers.
4) Wrap the threaded ends of the
headers with the provided Teflon
tape to ensure a watertight seal.
5) Locate the header that does not have
the white serial number label and
install the PVC end caps on either
end of that header.
6) Locate the header with the white
serial number label and install the
PVC elbow connectors on either end
of that header.
7) Turn the pool pump off and
ensure the handle of the filter
is in the OFF/CLOSED position.
8) Plug the return fitting to
prevent water loss.
9) Remove the flex hose
from the return fitting of
the pool and secure it to
the lower PVC elbow
connector using a stainless
steel clamp.
10) Secure another flex hose (not included) to the top PVC elbow and
return fitting of the pool using the stainless steel hose clamps
following the above system layout.
The collector is now installed and ready to use. Ensure that all
fittings are secure.
11) Remove the plug from return fitting and turn the handle of the
filter to the FILTER position.
12) Turn the pool pump to the ON position.
Note: Air bubbles may come through the return line during initial
start-up of the collector. This is normal and will stop after all the air has
been purged from the solar heating system.

www.smartpool.com5
1) Ensure there is adequate work space to unroll the 20’ collectors.
2) Remove the collectors from the box and the strap from around the
collectors. Slowly uncoil the panels.
Note: Laying the collectors in the reverse direction of the coils will help
flatten the panels.
3) Remove and discard the black protective caps covering the threaded
portion of the headers.
4) Join the headers with the white labels
together using a rubber hose connector
and two 1 1/2" hose clamps. Position the
hose clamps 1/2” in from each end of
rubber connector hose and tightens.
5) Locate the header that does not have
the white serial number label and
install the PVC end caps on either
end of that header.
6) Locate the header with the white
serial number label and install the
PVC elbow connectors on either end
of that header.
7) Turn the pool pump off and
ensure the handle of the filter
is in the OFF/CLOSED position.
8) Plug the return fitting to
prevent water loss.
9) Remove the flex hose
from the return fitting of
the pool and secure it to
the lower PVC elbow
connector using a stainless
steel clamp.
10) Secure another flex hose (not included) to the top PVC elbow and
return fitting of the pool using the stainless steel hose clamps
following the above system layout.
The collector is now installed and ready to use. Ensure that all
fittings are secure.
11) Remove the plug from return fitting and turn the handle of the
filter to the FILTER position.
12) Turn the pool pump to the ON position.
Note: Air bubbles may come through the return line during initial
start-up of the collector. This is normal and will stop after all the air has
been purged from the solar heating system.
S240 OR M LTI-SYSTEM INSTALLATION
This layout is for system of 2 or more collectors installed near the pool filter equipment. Installing the collector on a roof, rack or fence may
require additional plumbing and hardware kits.
Cool Water
(Feed)
War Water
(Return Fitting)
Pool Pu p
Elbow Connector
Elbow Connector
Black Rubber Connector Hose Labels
Filter
White End Caps
Feed Hose
Return Hose

Note: The mounting hardware is sold separately. See page X for available kit options.
Setup and Positioning
• Allow the collectors to lay in the sun for 30 minutes to relax the material and
flatten the panels.
• Ensure there is at least 1’ around all sides of the collector(s) for adequate space for
connectors and plumbing.
• Install the collectors on a slight angle toward and end cap for draining and
winterization.
• The panels can be placed on either side of a roof vent up to 3” in diameter.
• Ensure the collectors will have at least 6 hours of direct sun exposure.
Installation
Note: Below instructions are for mounting purposes only. For full collector
installation, please see the appropriate system layout provided in this manual.
1) Once positioning is established, locate the manufactured slots in the collector (5
slots in a 20’ collector).
2) Place the bracket in place and pre-drill a 1/8” pilot hole
for the screw.
3) Insert the screw using a Phillips head screwdriver to hold
the bracket in place (as shown).
Important: If installing on a roof, use a silicone sealant to prevent water leakage
into structure. Apply adequate amounts of
sealant to both the pre-drilled hole and over the screw head once installed.
4) Install a bracket on the bottom side of the panel
(as shown), ensuring that the bottom bracket is in line
with the top bracket.
Note: (15) brackets are provided with each kit, which will
support up to (2) 2’x20’ collectors. (10) brackets are used
for the top end of each 2’ panel and (5) are used for the
bottom of the second 2’ collector.
5) Once all brackets are installed, use the provided strapping to hold the collectors in
place. Tie a knot in the top bracket and feed the strap through the middle bracket
before tying the strap the bottom bracket (as shown).
www.smartpool.com 6
ROOF/RACK/FENCE INSTALLATION
RETURN FROM SOLAR
FEED TO SOLAR
Cool Water Feed
War Water Return
Filter
Check Valve Diverter Valve
Pipe
Adapter
Black Rubber Connector Hose
Vacuu Relief
End Cap
End Cap
Pu p
End Cap
End Cap
Pipe
Adapter
HARD PL MB SYSTEM LAYO T
Note: The SK22 (not included) is required for the following installation. See page 7 for available kit options.

IF A COLLECTOR DEVELOPS A LEAK
Your solar collectors are warranted against defects in materials and workmanship (see warranty for details and limitations).
If a leak develops for any other reason, you may use the repair method shown. The collectors are not warranted against freeze damage.
SOLAR COLLECTOR REPAIR
This method allows for an easy and permanent, on-site repair of a collector by isolating the leading riser tube. Referring to the
figure at the right, locate the tube to be isolated. (End tube has been shown for clarity). Using a sharp utility knife, very carefully
cut away approximately 1" (2.54 cm) of the tube at both headers. Drive a #10 sheet metal screw, preferably stainless, into the
hole in the header. The screw must be between 1/2" (1.27 cm) and 3/4" (1.9 cm) long. DO NOT OVER-TIG TEN!
If the screw strips out, or if the repair leaks, use a #12 screw. This repair method will not void the collector warranty.
With proper care and winterization, you will enjoy your solar collectors for many years.
www.smartpool.com7
WINTERIZATION
COLLECTOR REPAIR
YO R SOLAR SYSTEM M ST BE DRAINED FOR WINTERIZATION! FREEZE DAMAGE IS NOT COVERED NDER WARRANTY! YO
M ST DRAIN YO R SOLAR COLLECTORS J ST LIKE YO DRAIN THE REST OF YO R POOL EQ IPMENT!
Remove the vacuum relief valve at the top of the solar system. Remove the rubber end cap at the bottom and be sure ALL the water is drained out of the system. Replace end
caps and blow pressurized air in the reverse direction of normal water flow. This is the most effective way to drain your system. You can leave the collectors in place (as long as
they are completely drained) and they will withstand even the harshest winters. SmartPool recommends that you store your collectors inside in a warm dry place.
AVAILABLE KIT OPTIONS
SK22 : INGRO ND NIVERSAL SYSTEM KIT
Kit Components Qty
1.5" Diverter Valve 1
3.75" Rubber ose Connector 1
Pipe Adaptor 2
End Cap 1
Vacuum Relief Valve 1
Spring Check Valve 1
1.5" Stainless Steel Clamps 3
• Used for hard plumb installation
• Will support up to (8) S140U systems or (4) S240U
SK35: ABOVEGRO ND MAN AL DIVERTER VALVE KIT
Kit Components Qty
1.5" Ball Valve 1
1.5" PVC Tees 2
Flex ose Adaptors 4
• Used for flex hose installations.
• Will support S140U and S240U systems.
SK43: MO NTING KIT
Kit Components Qty
6' Web Strapping 5
Stainless Steel Mounting Brackets 15
#14 Stainless Steel Screws 15
• Used for mounting on roof, rack or fence.
• Will support up to (2) S140U or (1) S240U system(s).
SK34: HIGH WIND ADD-ON MO NTING KIT
Kit Components Qty
6' Web Strapping 4
Stainless Steel Mounting Brackets 4
#14 Stainless Steel Screws 4
• Used in conjunction with SK43 in areas of excessive wind.
• Will support (1) 2' x 20' collector.

www.smartpool.com
Problems Possibilities/Solutions
Sun eater does not appear to be
heating the pool.
• Make sure that water is flowing through Sun eater by checking the flow at the pool return.
• Note the weather - has it been cloudy or raining?
• Use your pool cover at night to reduce heat loss.
• Refer to our order guide - pool size may require additional collectors.
Bubbles continue to appear from
the pool water inlet during
operation.
• Check the connections for leaks.
• Check the flow rate.
• Check the tubing for leaks or clogging.
Sun eater leaks • Make sure connectors and hose clamps are tight and not defective.
TRO BLESHOOTING
Smar Pool Inc. warran s o he original purchaser of he Solar Collec or ha he company will, a i s op ion, repair or replace any solar collec or ha proves o be defec ive in ei her workmanship or
ma erial upon prepaid re urn of he collec or by he owner o Smar Pool, Inc., subjec o he provisions of he limi ed warran y s a ed above, and he exclusions and limi a ions se for h below.
Smar Pool, Inc. will, pursuan o he erms of his warran y, a i s sole op ion. ei her repair he collec or a a nominal charge o he owner, or replace he collec or per he pro-ra ed provisions s a ed
herein. All repaired or replaced collec ors will be re urned a he homeowner’s expense. The pro-ra ed basis for collec or replacemen is se for h above.
What is covere : The solar collec or is warran ed o be free of defec s in ma erial and workmanship when leaving he fac ory.
What is not covere : Hardware; including hoses, clamps and plas ic fi ings; Any damage due o freezing caused by or rela ed o improper drainage, win eriza ion, or s orage; Damage, defec s, malfunc ions, or
o her failures arising from use of he produc which does no comply wi h he ins ruc ions provided by he manufac urer; Damage, defec s, malfunc ions, or o her failure caused by or rela ed o repairs performed
by any servicer o her han an au horized service represen a ive of Smar Pool, Inc. Claims will no be accep ed for a collec or’s damage in ransi unless damage o shipping con ainer is no ed a ime of delivery on
he ranspor company’s delivery bill.
SMARTPOOL, INC. SHALL IN NO WAY BE LIABLE OR RESPONSIBLE UNDER ANY CIRCUMSTANCES OR IN ANY AMOUNT FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES OR FOR ANY
INJURY OR DAMAGES TO PERSON OR PROPERTY USING OR USED IN CONNECTION WITH THIS PRODUCT, OR FOR LOSS OF PROFITS OR OTHER COSTS OR EXPENSES OF ANY KIND OR
CHARACTER. THERE ARE NO OTHER WARRANTIES OR REPRESENTATIONS, EITHER EXPRESS OR IMPLIED, WHETHER OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
OTHER, MADE BY SMARTPOOL, INC., OTHER THAN THOSE SPECIFICALLY SET FORTH IN THIS WARRANTY. NO PERSON, FIRM, OR CORPORATION IS AUTHORIZED TO MAKE ANY
REPRESENTATIONS, OR INCUR ANY OBLIGATIONS IN THE NAME OF OR ON BEHALF OF SMARTPOOL, INC., EXCEPT AS STATED HEREIN. THIS WARRANTY IS EXPRESSLY UNDERSTOOD TO
BE THE EXCLUSIVE REMEDY AVAILABLE TO THE PURCHASER, AND THIS WARRANTY CONTAINS THE FULL AND COMPLETE AGREEMENT BETWEEN SMARTPOOL AND THE PURCHASER.
THIS WARRANTY SETS FORTH THE ONLY OBLIGATIONS OF SMARTPOOL WITH REGARD TO THIS PRODUCT, AND THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF.
The represen a ions se for h herein are he only represen a ions made by Smar Pool, Inc. wi h respec o he produc , and his warran y does no cons i u e ei her a performance or
sa isfac ion guaran ee. I is he responsibili y of he produc owner o regularly es and check he produc for proper func ion and safe y.
This warranty gives the original purchaser specific legal rights. You may have other rights depending on where you live.
ALL WARRANTY CLAIMS M ST BE HANDLED DIRECTLY
WITH SMARTPOOL. DO NOT RET RN TO YO R DEALER. SMARTPOOL ACCEPTS CLAIMS FROM POOL OWNERS ONLY.
FIVE YEAR WARRANTY
Five year limited warranty from date of urchase with one year full.
After the first year, the claimant shall ay the list rice at the date of the claim less one-sixtieth (1/60) of that
rice for each full month remaining in the warranty eriod.
1) Call 1-732-730-9880 to initiate a claim.
2) You will receive an instruction package within 10 days.
3) Please allow 2-4 weeks for warranty claims to be settled.
4) If you do not receive your collector within 6 weeks, please cal SmartPool Warranty
Department Monday through Friday at 1-732-730-9880.
SMARTPOOL SOLAR COLLECTOR
Five Year Limited Warranty
(Valid for North America Only)
To File a Claim: