Smartwares C935IP User manual

Wireless APP Camera
Installation and Operating Instructions
C935IP
Version 1.0
PLEASE READTHESE INSTRUCTIONSCAREFULLY BEFOREUSINGTHISPRODUCT
AND KEEP THIS MANUAL FOR FUTURE REFERENCE.

B
Camera Stand x 1
D Power Adapter x 1
F Rj45 Connect Jack x 1
F
Quick Start Guide x 1
KIT CONTENT
A
Wireless App Camera x 1
C Camera Antenna x 1
E Screw Pack x 1
G
Manual CD x 1
Tools Required:
Electric drill
5mm masonry drill bit
15mm masonry drill bit
No. 2 Philips screwdriver
For best system performance:
-iOS: iPhone4S / iPad2 / Mini iPad or above. Maximum 12 registered camera
connections.
-Android: 1.5G dual core processor or above / 960*540 pixel or above. Maximum 12
registered camera connections.
-Storage: Class 10 memory card.
-Bandwidth: 1Mbps or above upload/download speed suggested.

SAFETY AND INSTALLATION TIPS
Do not attempt to open the units with the power adaptor plug connected to
avoid any risk of personal injury.
When installing CCTV camera(s), always follow manufacturer's advice
when using power tools, steps, ladders, etc. and wear suitable protective
equipment (e.g. safety goggles) when drilling holes. Before drilling holes
through walls, check for hidden electricity cables and water pipes. The use
of cable/pipe detector is advisable.
It is also advisable to avoid exposing any cameras to extreme weather
conditions (e.g., under a gutter which is prone to any water leaks). When
installing any cameras with this unit, it is advisable to use cable conduit to
protect any video/power extension cables from being exposed externally
and to prevent/reduce the chances of the cables being tampered with. After
drilling any hole though an external wall for a cable, ensure the hole is
sealed up around the cable using a sealant to prevent drafts.
To prevent a fire or electrical shock hazard, do not attempt to open the
housing while the unit is exposed to rain, water or wet conditions. There
are no user serviceable parts inside. Refer servicing to qualified service
personnel. Avoid pointing the camera(s) directly at the sun or any bushes,
tree branches or moving objects that might unnecessarily cause the camera
to record.
5

NIGHTVISION
The camera has built-in infrared LEDs to allow you to view at night for
24-hour surveillance. The LEDs will automatically activate at night and the
picture viewed will turn to black and white. The night viewing range is up
to 5 meters.
CAMERA INSTALLATION
Secure camera stand on the
stable surface.
Loosen up the Thumb screw.
Adjust proper view angle then
secure the joint with T-bolt.
Ceiling Mount Wall Mount
6

CAMERA OVERVIEW
Antenna
Power Indicator
Signal Indicator
SD Card Slot
PIR Infrared LEDs
Stand
RJ-45 Cable
Power Cable
7

8
DOWNLOAD AND SETUP THE APP
The Wireless APP camera is designed todeliver live video footage directly
to your smart phone or tablet device. Please follow these steps to download,
setup and use the APP.
APP Name: OMGuard HD
Download the App
1. From you smart phone or tablet device, click the APP Store/Google Play
and search for “OMGuard HD”.
2. Once located the APP, select download.
3. Once download completed, you will find the APP icon on your mobile
device screen.
APP Setup
△
! BEFOREYOUSTART
Before connecting the camera to power source, first connect the camera to your
Wi-Fi router by using only the Ethernet cable provided.
After the camera is connected to the Wi-Fi router, connect the camera to power
source and wait until both RED and GREEN LED begin flashing. DO NOT begin
the setup process until both LEDs become steady on (roughly 45 seconds).
Please follow the steps in the following pages to complete the setup.

9
1. Make sure the mobile device you are using is connected to the same
Wi-Fi router the camera is connected to.
2. Locate the “OMGuard HD” icon in your mobile device and launch the
App.
3. Tap the ADD CAMERA icon to add a new camera. Then click
the SEARCH button for a quick setup. The APP will search available
camera(s) connecting to the Wi-Fi router and display the camera
information in the pop up list. Select the camera from the list and the
APP will automatically add the camera’s DID code to the DID column.
Enter the default password 123456.
(iOS) (Android)
Note: After you have entered the default password, the APP will remind you to
change the default password.
4. Click SAVE to complete the camera settings. The system confirms the
user identity and grants permission to user access.
5. You can refer to "ADD CAMERA" section for detail on adding additional
camera(s).

10
In most cases, you can successfully add the camera according to the steps
above. However, the camera will not find the network if Wi-Fi router turns
off the SSID broadcasting function. Please enable the SSID broadcasting to
complete the settings.
Note: Most Wi-Fi routers broadcast the Service Set Identifier (SSID) by default. This
is the name of your wireless network, and SSID broadcasting is how Wi-Fi-enabled
devices find networks.
The camera will only accept SSID composed with English alphabet charactors and
arebic numbers, none-English and special charactors (!@#$%, ect.) will not be
accepted.

11
LIVE VIEW / SNAPSHOT / RECORDING
Tap to take snapshot image(s) of the
video. The captured snapshots will be
stored in your mobile device.
Tap to turn ON/OFF the volume.
Tap to Start/Stop recording.
The recorded video file will be stored
in the memory card of your camera.
Tap to return to the main page.
The APP allows users to have access to live video. User can take snapshot
image(s) and record the live video.
When you launch the App on the smart phone or tablet, the image
displaying on the main screen is the very last automatically captured
snapshot from the live view of the previous established session. Tap the
image to enter live view mode.
The controls and layout of the APP have been customized to meet the
operating system requirements of the mobile device. The main page may
vary, depending on your mobile device. By default, the live view is
displayed in portrait mode. You can also turn the device sideways to switch
to landscape mode for a larger view.
Note: Once the recording is started by motion detection or manually, the APP will
continue the recording for 1 minute. User cannot stop the recording during this period.

12
VIEWING YOUR SNAPSHOTS
For iOS
You snapshots will be named with the time stamp and saved into the
Camera Roll location of your mobile device.
For Android
You snapshots will be named with the time stamp and saved into the
Photo Gallery > snapshot folder on your mobile device.
PLAYBACK YOUR VIDEOS
The recorded video file(s) on your camera is automatically saved to the
memory card inserted in your camera. You can remotely access the file(s)
for playback via your mobile device.
Tap the CAMERA SETTING icon on the main page.
(iOS) (Android)