Smartwares 271723 Operation and maintenance manual

IP SURVEILLANCE CAMERA
IAN 271723
IP SURVEILLANCE CAMERA
Quick-start guide with instructions for
assembly and use, and safety notices
105x148mm
Version 1.4
BEZPEČNOSTNÍ IP KAMERA
Quick Start Guide s návodem k montáži,
obsluze a bezpečnostními pokyny
IP-ÜBERWACHUNGSKAMERA
Quick-Start-Guide mit Montage-, Bedienungs-
und Sicherheitshinweisen

GB Assembly, operating and safety instructions Page 5
CZ Pokyny k montáži, obsluze a bezpečnostní pokyny Strana 23
DE/AT /CH Montage-, Bedienungs- und Sicherheitshinweise Seite 41
Before reading, unfold both pages containing illustrations and familiarise yourself with all
functions of the device.
Před čtením si odklopte obě dvě strany s obrázky a potom se seznamte se všemi funkcemi
přístroje.
Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie
sich anschließend mit allen Funktionen des Gerätes vertraut.
100x148mm

100x148mm
B
1 2 3 4
5 6 7
8
129
10
11
AA1 A2 A3
13

105x148mm
C
D
E

105x148mm
H
F
G

100x148mm
I
J

5GB
List of pictograms used............................................ Page 6
Introduction
Intended use............................................................................ Page 7
Parts Description...................................................................... Page 8
Technical Data ........................................................................ Page 8
Scope of delivery.................................................................... Page 9
Safety instructions....................................................... Page 10
Installing the camera................................................. Page 13
Connecting the camera .......................................................... Page 14
Camera setup.......................................................................... Page 15
Changing passwords and configuring the camera
on the WLAN network............................................................ Page 15
Using the camera.................................................................... Page 17
Troubleshooting ............................................................ Page 18
Cleaning and Care....................................................... Page 19
Disposal................................................................................ Page 19
Warranty and Service
Warranty Declaration............................................................. Page 20
Service address....................................................................... Page 20
Notes on Conformity................................................. Page 21
Trademark notices....................................................... Page 22

6 GB
List of pictograms used
Read the instructions!
Safety instructions
Directions for use
Dust- and hose-proof
DANGER: This symbol with wording "DANGER" indicates
a hazard which may result in
serious injuries or death if
not observed
. To avoid the da nger, follow the instruction.
WARNING: This symbol with the wording "WARNING"
indicates a hazard which may result in injuries or property
damage if not observed. To avoid the danger, follow the
instruction.
Keep out of reach of children!
Dispose of the packaging and the product in an environ-
mentally compatible manner!

7GB
IP Surveillance Camera
Introduction
Congratulations on the purchase of your new product. In
doing so you have chosen a top-quality product. Familiarise
yourself with the product before using it for the first time To do
so, carefully read the following quick-start guide including instructions
for assembly and use, and safety notices. The product also includes a
tutorial CD providing more information on the special function of the
camera, including connecting it to a PC. Only use the product as indi-
cated and for the specified areas of application. Both instructions for
use (quick-start guide + tutorial CD) are part of this product. Keep these
for future reference. If you pass the product on to anyone else, please
be sure to also include all documentation.
Intended use
This camera fall into the category information technology. The product
is suitable for use indoors or in protected outdoor areas and is for the
surveillance of garages, car parks, house entrances, etc. The camera
features a night vision function with 6 infrared LEDs and provides clear
image transmission. It also features a built-in microphone for recording
ambient noise. Transmission is sent to a router, from where it can be
accessed and controlled via app. Any use other than previously described
or modifying the product is prohibited and will result in damage. The
manufacturer is not liable for any damages caused by improper use.
This product is not intended for commercial use.

8 GB
Parts Description
Before reading, unfold the page containing the illustrations and famil-
iarise yourself with all functions of the device.
1Camera
2Mounting bracket
3WLAN aerial
4Tutorial CD
5Wall plug
6Screws
7Power supply
8Ethernet cable (see Fig. B)
9RJ-45 connection element
10 RESET button (see Fig. B)
11 SD slot (for micro SD card max. 32GB Class 10 - not included)
(see Fig. B)
12 Quick start guide with instructions for assembly and use, and
safety notices
13 Decal for marking the area under surveillance
Technical Data
Camera:
Device type: Surveillance Camera WLAN Outdoor
IP66
Dimensions: approx. 6 x 11cm (ø x d), approx.
6 x 15.5cm (ø x d) (with WLAN aerial
and sun screen)
Image sensor: 2 megapixel CMOS
Focal length: 3.6mm

9GB
Resolution (horizontal TV lines): 1280 x 720 pixel
Picture angle: h 65°, v 38°
Detection range
Motion detector: 90° x 5m
Infrared range (night vision
mode black/ white): 6 IR LEDs up to 8m range
Light sensitivity: 1–8LUX
Operating temperature: -10°C – +50 °C
Humidity during use: 40–80% RH
Storage temperature: -10°C – ~+60 °C
Humidity during storage: 20–90% RH
Connections: Ethernet (10/ 100 Base-T/ Base-TX);
WLAN IEEE 802.11b/ g/ n
Frequency: 2.4 GHz
Protection class: IP66 (dust- and hose-proof)
Weight: approx. 540g (camera with base,
aerial and sun screen)
Power supply (for dry indoor use only):
Model/type: CS9C050150FGF
Manufacturer: CSEC
Input voltage/frequency: 100–240V~, 50 /60 Hz
Input current: 500mA
Output voltage: 5V DC
Output current: 1.5A
Protection class: II/
Scope of delivery
Remove all parts from packaging and dispose of all packaging material.
Please contact customer service if parts are missing or damaged.

10 GB
1 Camera
1 Mounting bracket
1 WLAN aerial
1 Power supply
1 Mounting kit
1 Tutorial CD
1 RJ-45 connection element
2 Decals for marking the area under surveillance
1 Quick-start guide with instructions for assembly and use, and safety
notices
Safety instructions
Damage due to failure to comply with these instructions for use will
void the warranty! We assume no liability for consequential damage!
We assume no liability for property damage or personal injury due to
improper handling or failure to observe the safety notices!
Children and persons with limitations
DANGER TO LIFE AND RISK
OF ACCIDENT FOR INFANTS AND CHILDREN!
Never leave children unsupervised with the packaging
material. The packaging material poses a suffocation hazard. Pack-
aging materials are not toys. Children frequently underestimate the
dangers.
Always keep children away from the product. This device may be
used by children aged 8 years and up, as well as by persons with
reduced physical, sensory or mental capacities, or lacking experi-
ence and/or knowledge, when supervised or instructed in the
safe use of the device and they understand the associated risks.

11GB
Do not allow children to play with the device. Cleaning and user
maintenance must not be performed by children without supervision.
DANGER TO LIFE! During installation keep children away from
the area in which you are working. A large number of screws and
other small parts are included within the scope of delivery. These
may prove life-threatening if swallowed or inhaled.
Damage
Never use the product if it is damaged in any way.
Contact your service centre or a professional if the product is dam-
aged, requires repairs, or for any other problems with the product.
Ensure all electrical connections and cable connections to other
devices comply with the applicable guidelines and with the instruc-
tions for use.
Be sure not to overload socket and extension cables. This can lead
to fire or electric shock.
Please note the temperature and humidity during operation and
storage to ensure proper camera operation. These are specified in
the technical data. Moist, very cold or hot environments or storage
can damage the camera.
The camera is suitable for outdoor use, the power supply may only
be used indoors.
Avoid major shock. This can damage the electronic circuit.
Cordless systems are exposed to interference of telephones,
microwaves, as well as other electronic devices operating in the
2.4 GHz range (impacts of interference include poor image quality
or transmission problems).
Maintain a minimum distance of 3 metres during installation and
operation.
Do not open the camera. This is a maintenance-free camera. Open-
ing the product will void the warranty.
Be sure not to damage any wires during installation.

12 GB
AC Adaptor
Only plug the power supply into easy to access sockets so it can
easily be unplugged in the event of an emergency.
Do not touch the power supply with wet hands. Otherwise there is
a risk of electric shock.
Only use the power supply in dry indoor spaces.
Never unplug the device by the cable. Always touch the device by
the housing.
Please remember the power supply will continue to draw a small
amount of electricity even without the camera being operated so
long as the power supply is plugged into the socket. To completely
disconnect the power supply it must be unplugged from the mains
socket.
DANGER TO LIFE! Never open the power supply. Otherwise
there is a risk of electric shock.
Never cover the power supply.
Immediately unplug the power supply if you notice unusual noises
or smoke.
Position the cable so as to avoid a trip hazard.
Protect all plug connectors from moisture.
Application
Do not use the camera in explosive environments, e.g. at tank
plants, or in dusty environments.
Observe applicable national laws if you intend to use this camera
to photograph or watch people.
Areas under camera surveillance must be marked. The respective
decals are included, please again observe the labelling require-
ments of the respective country.
Do not place any liquid-filled containers such as vases or drinks on
or near the device. Shield the power supply from drips or sprays.

13GB
Keep away from open flames. For example, do not place any
burning candles on or near the device. That way you can avoid
the spread of fire.
Installing the camera
Note: Mount the camera at a height and position at which it cannot
be reached without aid. Proceed likewise with the connecting and
Ethernet cable.
Be sure not to pierce electrical lines or other obstructions during
installation.
Before mounting the product to the wall, check which mounting
materials are suitable for your wall.
Hold the mounting bracket 2against the wall in the desired
mounting position and mark the drill holes on the wall using the
predrilled holes.
CAUTION! RISK OF INJURY! Please refer to your electric
drill‘s instructions for use.
Now drill the mounting holes (Ø 5mm). Ensure that you do not
damage the supply line.
Now insert the wall plugs 5into the bore holes.
Secure the mounting bracket 2to the wall using the screws 6
(Fig. A1).
Loosen the wing bolt on the mounting bracket 2and adjust the
viewing angle (see Fig. A2).
Then secure the joint by tightening the wing bolt.
Screw the camera 1onto the mounting bracket 2(see Fig. A3).
Once the you have turned the camera
1
on the screw in the mounting
bracket 2so it is connected as tight as possible, turn the triangle
nut in the opposite direction to secure the camera 1.

14 GB
Note: For details and more information, please refer to the included
tutorial CD 4.
Connecting the camera (see Fig. B)
Connect the Ethernet cable 8with the router.
Plug the connector of the power supply 7into the camera 1.
Plug the power supply 7into the socket.
Wait about 45 seconds after connecting to the electric circuit. Once
the red and green LED on the camera light up, it is connected to
the network.
The red LED indicates the camera is connected with the power
supply. The green LED indicates the camera is connected with the
router.
Note: To use the camera to record, insert an SD card in the SD slot
(see Fig. B).
Open the rubber cover.
Slide the SD card, pins down, into the SD slot 11 .
Carefully push the SD card against the resistance of the spring.
The SD card is now locked in place.
To remove the SD card, lightly push against the SD card using
your fingernail.
The spring will now slightly push the SD card out of the SD slot 11 .
The SD card can now be removed.
Close the rubber cover to prevent water from entering.

15GB
Camera setup
Download the „OMGuard HD“ app from the App Store or Google
Play (see Fig. C).
In the app, select „Add new system“ and „Scan“ to select the
camera 1you wish to connect to the router. This will open a new
window with all the cameras available on the network. The camera
will have an alphanumeric code which also corresponds with the
„DID Code“ printed on a label on the underside of the camera.
Compare the codes and select it in the display. Select a name for
the camera and enter it under system name. Then enter the default
security code „123456“ and click „Save“ (see Fig. D). The camera
will capture a still frame and show it in the display along with the
message „Connected“.
Changing passwords and configuring the
camera on the WLAN network (see Fig. E)
Note:You will find the expanded description in the tutorial CD.
Select the „Camera Settings“ symbol, then „System Informa-
tion“ for additional camera configuration.

16 GB
Select „More“ and enter the default Admin password „123456“.
Click „OK“ to confirm.
Opening „More“ for the first time will open a window prompting
you to enter a new Admin password. You will need to enter a new
password or you will be unable to access the settings. To change
the password again later, scroll all the way up in the „Adv. Set-
tings“ menu until you see the item „Admin Password“. Then enter
your old password, followed by the new one. Enter it again to
confirm the new password.
Scroll down until you see the field „Security Code“. Select „Change“.
Enter the default old password („123456“) and select a new
password and repeat to confirm your entry. Click „OK“ to confirm
your entry.
Scroll down until you see the „WLAN Config.“ field. Select „Adv.
WLAN network“ (see Fig. G).
Once you have successfully entered your WLAN password the
camera will restart. Please disconnect the network plug from the
router when restarting.
The security code allows you to access the camera („Live View“,
not for changing settings) and the „Admin Password“ is used to
change any camera settings.
IMPORTANT: The camera software requires two passwords – the
security code for accessing the camera, and the admin password for
configuring the camera.The factory setting for both passwords is
„123456“. After changing the passwords the new passwords must be
used, not the default password. Please remember the passwords.
Be sure to change both passwords to prevent unauthorised access
to the camera.

17GB
Using the camera
Please check the preview image (still frame) (see Fig. H). Select
the camera image and enter your new security code. You will now
see the „Live Image“ from the camera (see Fig. I).
For an IOS device select in the app to view a live camera
recording (see Fig. J right).
Or alternatively select for an ANDROID device to view a live
camera recording (see Fig. J left).
Select to take a screen shot. The picture will be saved to your
mobile and gallery/photos.
Select to switch the audio on/off in LIVE mode.
Select to record. It will then record for one minute and stop
automatically.
Select to return to the main screen of the App.
To use the playback function, select , then from the main
screen of the app.
Now select the file you wish to play from the results (see Fig. J,
Android: left, IOS: right). The app will now start the playback.
Use the pause symbol to pause playback, use return to the
playback list.
At the very top you will see information related to name, connec-
tion and image quality*.
There are 4 displays:
A – camera name: user specified
B – connection status: connecting/connected /disconnected
C – Resolution information: various by resolution selected.
(1280X720/640X480)
D – connection type and connection quality: unknown (app does
not recognise the type of connection) /Direct link (camera
and mobile on the same network)/Indirect link (camera and

18 GB
phone on different networks - connected via internet) Connec-
tion quality = good/normal /poor.
Note: For details and more information, please refer to the included
tutorial CD 4.
Notice to Android users: Close the app after viewing the camera
image on your mobile. To do so, from the main screen in the app,
press and hold the respective button at the bottom left corner of the
display. The EXIT command will appear. Select it to close the app.
Note: Depending on the operating system and version you may not
have full access to all functions.
Troubleshooting
No image appears.
Check the display (LED) on the camera.
Verify the camera is connected to power with the included
adapter.
Check the connections of the Ethernet cable.
The camera does not respond, the camera image freezes.
Hold the RESET button 10 for approx. 45 seconds to restart.
Whilst holding the button, first the red, then the green, and finally
the red LED again, will flash. After releasing the RESET button 10
it will take approx. 45 seconds for the camera to reconnect to the
network. After this, the red and green LED will light up. The green
LED will light up when the camera is connected to the tethered net-
work. The camera is now again ready for use.
All settings will be reset to the factory settings. It will need to be
completely reconfigured.