SMB citytor Original11 BT 02 Manual

Technical Information
Type BT 02
Page 1
Testing standard: EN 1176-1:2008 / EN 15312:2007
07.01.15
General
The described work is to be carried out by qualified specialists.
Dimensions
Width 3,17 m
Height 2,08 m
Depth 0,80 m
Age group
No age restriction
Supplied Tools:
1 socekt key-insertion 1/2" size 14
Tools additionally required:
1 ratch 1/2"
1 torx socket key T30
*The mounting equipment is in a box, which is
attached to a tube of the goal (lower left
corner)
Technical Details
The smb citytor original II is made of screwable round tubes with a diameter of 82,5 x 3,2 mm for the frame
tubes in the front and 60,3 x 2,9 mm for the frame tubes in the back. The net of the goal is made of black
Herkules rope, 8 mm. The maximum mash size is 36 x 122 mm, so that EN 1176-1 is met for children from
0 to 3 years.
Figure 1 citytor II
ATTENTION!
Due to the technical characteristics of the goal, especially the mash size of 36 x 122 mm, it is not
climbable.
This goal meets the standards of DIN EN 1176-1:2008 as well as DIN EN 15312:2007.

Technical Information smb Seilspielgeräte GmbH Berlin
Technikerstraße 6/8
Type BT 02 D - 15366 Hoppegarten
Phone [phone]
Fax [phone]
www.smb-seilspielgeraete.de
Page 2
Technical Details
The net ends are pressed into aluminum sleeves by taking three ropes at a time. These pressed
aluminum sleeves, located in the back of the net parts and in both side parts, are inserted into the
ROWOCON®-sleeves and fixed with setscrews M10x8 A2, Torx T30. These setscrews have a polyamide
spot coating to prevent removal. This connection also prevents an unwanted loosening of the
screwing and enables at the same time an easy exchange of the nets, without having to remove or
disassemble the entire goal
Placing of the ground anchors into the concrete foundations
The ground anchors are to be set into the concrete foundations on the same level as the play level.
Please make sure that the side with the movable slide block shows to the top (figure 4). We have
calculated a depth of 150 mm for the sub-construction of the play level. According to this, the top edge of
the foundations C20/25 (B25) is 150 mm below play level. When placing the concrete, a drainage is to be
provided (Figure 2).
If the sub construction needs to be larger as 150 mm, please consult smb.
The correct screwing and positioning of the goal depends on the correct placing of the
ground anchors!
Thus, the work is to be carried out accurately, taking into account the measurements of the
drawing.
Figure 2
All measurements in mm!

1 Ground anchor with slide block
2 Plastic washer
3 bolt M10x8 A2 DIN 916 Torx30
4 ROWOCON®-connection
5 Screw M16x70
6 Rope of the goal net
7 Lock washer
Technical Information smb Seilspielgeräte GmbH Berlin
Technikerstraße 6/8
Type BT 02 D - 15366 Hoppegarten
Phone [phone]
Fax [phone]
www.smb-seilspielgeraete.de
Page 3
Screwing the smb-citytor II with the ground anchors
The ROWOCON®-sleeves (4) in the side parts of the smb-citytor original II are to be provided with
screws M16 (5) and lock washers (7). The ropes (6) of the goal net are not fixed at this point (Figure
4).
Remove the safety covers of the ground anchors with a screwdriver (Figure 3). The entire goal is to be
adjusted via the ground anchors (1). We recommend the storage of the safety covers for a possible
reuse later on.
Now the supplied screws M16x70 (5) and lock washers (7) can be bolted with the help of the provided
socket key insertion. The flexibility of the slide blocks in the ground anchors (1) can balance dimension
inaccuracies. The safety caps (figure 3) close the openings of the ground anchors (1).
After having bolted everything, the ropes of the goal net (6) need to be inserted into the ROWOCON®-
sleeves (4) and screwed in with the setscrews (3) by using the torx socket key T30.
Figure 3
Figure 4

Technical Information smb Seilspielgeräte GmbH Berlin
Technikerstraße 6/8
Type BT 02 D - 15366 Hoppegarten
Phone [phone]
Fax [phone]
www.smb-seilspielgeraete.de
Page 4
Maintenance instructions EN 1176-1
Visual routine inspection
Frequency will be based on local conditions (high/low use, vandalism, air pollution, effects of weather).
The nets are to be checked for damage.
oIf a strong damage is discovered, e.g. a break in the wire, smb needs to be consulted.
oIf only the rope coating is damaged and no wire is broken, there is no urgent need for repair.
Please Note: Frayed filament can be fused with a flame (e.g. pocket lighter).
Operational inspection (semi-annual)
(in addition to the visual routine inspection)
Check the ROWOCON®-connections for a firm fit.
oIf a damage is discovered, smb needs to be consulted.
The screwing of the goal frame needs to be checked (missing safety caps are to be replaced)
oIf necessary, re-tighten the screwing.
Check the stability of the goal.
oStand in front of the goal and at the top crossbar, tilt it back and forth.
oIf there is a noticeable instability / tilting, check the respective boltings and re-tighten. See
figure 4 for the procedure.