SMC Networks 5MC2671W User manual

38 Tesla
Irvine, CA 92618
Phone: [phone]
EZ Connect
TM
2.4 GHz
Wireless Ethernet Adapter
User Guide
From SMC’s EZ line of low-cost workgroup LAN solutions
November 2003
150000024600E R01 F1.0

Copyright
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable.
However, no responsibility is assumed by SMC for its use, nor for any infringements of patents
or other rights of third parties which may result from its use. No license is granted by
implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to
change specifications at any time without notice.
Copyright © 2003 by
SMC Networks, Inc.
38 Tesla
Irvine, CA 92618
All rights reserved.
Trademarks:
SMC is a registered trademark; and EZ Connect is a trademark of SMC Networks, Inc. Other
product and company names are trademarks or registered trademarks of their respective
holders.

i
C OMPLIANCES
FCC - Class B
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
the interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
FCC Caution: To assure continued compliance, (example - use only shielded
interface cables when connecting to computer or peripheral devices) any changes
or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement
FCC Radiation Exposure Statement: This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled environment. This equipment should
be installed and operated with a minimum distance of 20 centimeters (8 inches)
between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.

C OMPLIANCES
ii
Industry Canada - Class B
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus as set out in the interference-causing equipment standard
entitled “Digital Apparatus,” ICES-003 of the Department of Communications.
Cet appareil numérique respecte les limites de bruits radioélectriques applicables
aux appareils numériques de Classe B prescrites dans la norme sur le matériel
brouilleur: “Appareils Numériques,” NMB-003 édictée par le ministère des
Communications.
EC Conformance Declaration
SMC contact for these products in Europe is:
SMC Networks Europe,
Edificio Conata II,
Calle Fructuós Gelabert 6-8, 2o, 4a,
08970 - Sant Joan Despí,
Barcelona, Spain.
Marking by the above symbol indicates compliance with the Essential
Requirements of the R&TTE Directive of the European Union (1999/5/EC). This
equipment meets the following conformance standards:
• EN 60950 (IEC 60950) - Product Safety
• EN 300 328 - Technical requirements for 2.4 GHz radio equipment
• EN 301 489-1 / EN 301 489-17 - EMC requirements for radio equipment
Countries of Operation & Conditions of Use in the European
Community
This device is intended to be operated in all countries of the European
Community. Requirements for indoor vs. outdoor operation, license requirements
and allowed channels of operation apply in some countries as described below:
Note: The user must use the configuration utility provided with this product to
ensure the channels of operation are in conformance with the spectrum
usage rules for European Community countries as described below.
• This device requires that the user or installer properly enter the current country
of operation in the command line interface as described in the user guide,
before operating this device.
• This device will automatically limit the allowable channels determined by the
current country of operation. Incorrectly entering the country of operation may
result in illegal operation and may cause harmful interference to other system.
The user is obligated to ensure the device is operating according to the channel
limitations, indoor/outdoor restrictions and license requirements for each
European Community country as described in this document.
0560

C OMPLIANCES
iii
• This device may be operated indoors or outdoors in all countries of the
European Community using the 2.4 GHz band: Channels 1 - 13, except where
noted below.
- In Italy the end-user must apply for a license from the national spectrum
authority to operate this device outdoors.
- In France outdoor operation is only permitted using the 2.4 - 2.454 GHz band:
Channels 1 - 7.
Declaration of Conformity in Languages of the European
Community
English Hereby, SMC Networks, declares that this Radio LAN device is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Finnish Valmistaja SMC Networks vakuuttaa täten että Radio LAN device
tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja
sitä koskevien direktiivin muiden ehtojen mukainen.
Dutch Hierbij verklaart SMC Networks dat het toestel Radio LAN device
in overeenstemming is met de essentiële eisen en de andere
relevante bepalingen van richtlijn 1999/5/EG
Bij deze SMC Networks dat deze Radio LAN device voldoet aan
de essentiële eisen en aan de overige relevante bepalingen van
Richtlijn 1999/5/EC.
French Par la présente SMC Networks déclare que l'appareil Radio LAN
device est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE
Swedish Härmed intygar SMC Networks att denna Radio LAN device står
I överensstämmelse med de väsentliga egenskapskrav och
övriga relevanta bestämmelser som framgår av direktiv 1999/5/
EG.
Danish Undertegnede SMC Networks erklærer herved, at følgende
udstyr Radio LAN device overholder de væsentlige krav og
øvrige relevante krav i direktiv 1999/5/EF

C OMPLIANCES
iv
German Hiermit erklärt SMC Networks, dass sich dieser/diese/dieses
Radio LAN device in Übereinstimmung mit den grundlegenden
Anforderungen und den anderen relevanten Vorschriften der
Richtlinie 1999/5/EG befindet". (BMWi)
Hiermit erklärt SMC Networks die Übereinstimmung des Gerätes
Radio LAN device mit den grundlegenden Anforderungen und
den anderen relevanten Festlegungen der Richtlinie 1999/5/EG.
(Wien)
Greek
Italian Con la presente SMC Networks dichiara che questo Radio LAN
device è conforme ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 1999/5/CE.
Spanish Por medio de la presente SMC Networks declara que el Radio
LAN device cumple con los requisitos esenciales y cualesquiera
otras disposiciones aplicables o exigibles de la Directiva 1999/5/
CE
Portuguese SMC Networks declara que este Radio LAN device está
conforme com os requisitos essenciais e outras disposições da
Directiva 1999/5/CE.

C OMPLIANCES
v
Safety Compliance
Underwriters Laboratories Compliance Statement
Important! Before making connections, make sure you have the correct cord set.
Check it (read the label on the cable) against the following:
The unit automatically matches the connected input voltage. Therefore, no
additional adjustments are necessary when connecting it to any input voltage
within the range marked on the power adapter.
Operating Voltage Cord Set Specifications
120 Volts UL Listed/CSA Certified Cord Set
Minimum 18 AWG
Type SVT or SJT three conductor cord
Maximum length of 15 feet
Parallel blade, grounding type attachment plug
rated 15 A, 125 V
240 Volts (Europe only) Cord Set with H05VV-F cord having three
conductors with minimum diameter of 0.75 mm2
IEC-320 receptacle
Male plug rated 10 A, 250 V

C OMPLIANCES
vi
Wichtige Sicherheitshinweise (Germany)
1. Bitte lesen Sie diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie
keine Flüssigoder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes
Tuch zur Reinigung.
4. Die Netzanschlu ßsteckdose soll nahe dem Gerät angebracht und leicht
zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen
oder Fallen könnte Beschädigungen hervorrufen.
7. Die Belüftungsöffnungen dienen der Luftzirkulation, die das Gerät vor
Überhitzung schützt. Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt
werden.
8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.
9. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann.
Es sollte auch nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten.
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es
vom Stromnetz trennen. Somit wird im Falle einer Überspannung eine
Beschädigung vermieden.
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten
in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag
auslösen.
13. Öffnen sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen
und von einer qualifizierten Servicestelle zu überprüfen:
a.Netzkabel oder Netzstecker sind beschädigt.
b. Flüssigkeit ist in das Gerät eingedrungen.
c. Das Gerät war Feuchtigkeit ausgesetzt.
d.Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert
oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
e.Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
15. Stellen Sie sicher, daß die Stromversorgung dieses Gerätes nach der EN
60950 geprüft ist. Ausgangswerte der Stromversorgung sollten die Werte von
AC 7,5-8 V, 50-60 Hz nicht über oder unterschreiten sowie den minimalen
Strom von 1 A nicht unterschreiten.
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt
70 dB(A) oder weniger.

vii
T ABLE OF C ONTENTS
EZ Connect™ 2.4 GHz Wireless Ethernet
Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Package Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Hardware Description . . . . . . . . . . . . . . . . . . . . . . . 3
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . 7
System Configuration . . . . . . . . . . . . . . . . . . . . . . . 8
EZ Installation Wizard . . . . . . . . . . . . . . . . . . . . . . . 9
Using IPCONFIG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Utility Installation and Configuration . . . . . . . . . 11
Using the Configuration Utility . . . . . . . . . . . . . . . . . . . . . . 12
Utility Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
IP Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Statistic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Wireless Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
About . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Configuring Your IP Address . . . . . . . . . . . . . . . . 25
Windows 98/Me . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Web Management . . . . . . . . . . . . . . . . . . . . . . . . . 33
Browser Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

T ABLE OF C ONTENTS
viii
Disable Proxy Connection . . . . . . . . . . . . . . . . . . . . . . . 33
Internet Explorer (5.5 or above) in Microsoft Windows . 33
Internet Explorer in Macintosh . . . . . . . . . . . . . . . . . . . . 33
Navigating the Web Browser Interface . . . . . . . . . . . . . . . 34
Making Configuration Changes . . . . . . . . . . . . . . . . . . . 34
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
MAC Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Network Configuration and Planning . . . . . . . . .52
Network Topologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Ad Hoc Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Infrastructure Wireless LAN . . . . . . . . . . . . . . . . . . . . . . 53
Infrastructure Wireless LAN for Roaming Wireless PCs 54
A Wireless LAN with Internet Access . . . . . . . . . . . . . . . 55
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . .56
SMC Networks 802.11b Wireless Product
Maximum Distance Table . . . . . . . . . . . . . . . . . . . . . . . . . 57
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

1
EZ C ONNECT
™
2.4 GH Z
W IRELESS E THERNET A DAPTER
Introduction
SMC’s EZ Connect 2.4 GHz Wireless Ethernet Adapter
(SMC2671W) can function as:
•an Ethernet adapter, providing a wireless connection via an
RJ-45 connection to devices such as Microsoft Xbox and
Ethernet ready embedded devices
•a standard IEEE 802.11b access point
•a wireless range extender, allowing you to effectively extend
the coverage of another SMC2671W that is configured to
operate in Access Point mode
This solution offers fast, reliable wireless connectivity with
considerable cost savings over wired LANs (eliminates long-term
maintenance overhead for cabling). Just install enough wireless
access points to cover your network area, plug wireless cards into
your notebooks or install wireless adapters into your desktops,
and start networking.
Use this device in conjunction with SMC’s EZ Connect Wireless
Cards to create an instant network that integrates seamlessly
with Ethernet LANs. Moreover, moving or expanding your network
is as easy as moving or installing additional access points – no
wires!

EZ C ONNECT ™ 2.4 GH Z W IRELESS E THERNET A DAPTER
2
Package Checklist
The EZ Connect 2.4 GHz Wireless Ethernet Adapter package
includes:
•One EZ Connect 2.4 GHz Wireless Ethernet Adapter
(SMC2671W)
•One 5 VDC power adapter
•Installation CD containing this User Guide, EZ Installation
Wizard, and Utility program
•One RJ-45 cable
Please register this product and upgrade the product warranty on
SMC’s web site at http://www.smc.com
Inform your dealer if there are any incorrect, missing, or damaged
parts. If possible, retain the carton, including the original packing
materials. Use them again to repack the product in case there is a
need to return it.

3
H ARDWARE D ESCRIPTION
The Wireless Ethernet Adapter supports 1, 2, 5.5 and 11 Mbps
half-duplex connections to Ethernet networks. This device is fully
compliant with 2.4 GHz DSSS CSMA/CA wireless networking as
defined in IEEE 802.11b. It can be connected via an RJ-45
connection to devices such as Nintendo GameCube, Microsoft
Xbox, Sony PlayStation II, and Ethernet ready embedded
devices. It can also function as an IEEE 802.11b Access Point or
as a Range Extender (see “Introduction” on page 1).
Figure 1. Rear Panel
Note: If you use the RELOAD button at the bottom, the Wireless
Ethernet Adapter performs a power reset. If the button is
depressed for over 5 seconds, all the LEDs will illuminate
and the factory settings will be restored.
Item Description
Power Inlet Connect the included power adapter to this inlet.
Warning: Using the wrong type of power adapter may damage
your adapter.
LAN Port Fast Ethernet port (RJ-45). Connect device (such as a PC, hub
or switch) on your local area network to this port.
MDI/MDIX
Switch Press down the switch to connect to a network device with a straight-through twisted-pair cable; otherwise, connect to the
network device with (MDI-X) station ports at both ends by using
crossover cabling.
Power Connector
RJ-45 Port
MDI/MDIX Switch

H ARDWARE D ESCRIPTION
4
Applications
EZ Connect wireless products offer a fast, reliable, cost-effective
solution for wireless Ethernet client access to the network in
applications such as:
• Video Game Systems
Provides wireless Internet access for users of video game
systems such as Nintendo GameCube, Microsoft Xbox and
Sony PlayStation II
• Remote access to corporate network information
Email, file transfer, and terminal emulation
• Difficult-to-wire environments
Historical or old buildings, asbestos installations, and open
areas where wiring is difficult to employ
• Frequently changing environments
Retailers, manufacturers, and banks which frequently
rearrange the workplace or change locations
• Temporary LANs for special projects or peak periods
Trade shows, exhibitions, and construction sites that need a
temporary setup. Retailers, airline, and shipping companies
that need additional workstations for peak periods. Auditors
who require workgroups at customer sites
• Access to databases for mobile workers
Doctors, nurses, retailers, or white-collar workers who need
access to databases while being mobile in a hospital, retail
store, in an office, or on a campus
• SOHO users
SOHO (Small Office and Home Office) users who need easy
and quick installation of a small computer network

LED I NDICATORS
5
LED Indicators
The Wireless Ethernet Adapter includes three status LED
indicators, as described in the following figure and table.
Figure 2. Front Panel
LED Status Description
Wireless
Link TX/RX Flashing (Green) The device is transmitting or receiving data through wireless links.
Ethernet
Status LNK/ ACT On (Orange) The device has established a valid 10 Mbps Ethernet link.
On (Green) The device has established a valid
100 Mbps Ethernet link.
Flashing The device is transmitting or receiving
data on the Ethernet LAN
Power (PWR) On (Red) Power is being supplied.

H ARDWARE D ESCRIPTION
6
System Requirements
Before you install the Wireless Ethernet Adapter, be sure you
have met the following requirements:
•An AC power outlet (100~240 V, 50~60 Hz)
•An available RJ-45 (UTP) port on an Ethernet hub or switch
•802.11b compliant wireless Ethernet adapters with TCP/IP
protocols installed
•TCP/IP network protocol installed on each PC that needs to
access the Internet
•A web browser, such as Microsoft Internet Explorer 5.5 or
above installed on one PC at your site for configuring the
Wireless Ethernet Adapter

7
H ARDWARE I NSTALLATION
1. Select the site – Choose a location for your Wireless Ethernet
Adapter. Usually, the best location is at the center of your
wireless coverage area, if possible within line-of-sight of all
wireless devices.
2. Place the Wireless Ethernet Adapter in a position that gives it
maximum coverage. Normally, the higher you place the
antenna, the better the performance.
3. Position the antennas in the desired positions. For more
effective coverage, position the antennas along different axes.
For example, try positioning the antennas around 45 to 90
degrees apart. (The antennas emit signals along the
toroidal plane – and thus provide more effective
coverage when positioned along different axes.)
4. If used in Ethernet Adapter mode, connect the Ethernet cable
to the RJ-45 socket of the device that will communicate over a
wireless connection with an access point.
5. If used in Acces Point mode, connect the SMC2671W to an
Ethernet network device such as a hub or a switch using
category 3, 4, or 5 UTP Ethernet cable and an RJ-45
connector. (See “Hardware Description” on page 3 for MDI/
MDI-X cabling.)
6. Connect the power adapter cable to the 5 VDC power socket
on the rear panel.
Warning: Use only the power adapter supplied with the
SMC2671W.

8
S YSTEM C ONFIGURATION
The SMC2671W is a Plug-and-Play device. This means that, in
most cases, you will not need to configure it.
The SMC2671W Wireless Ethernet Adapter includes an SNMP
agent that is accessible through an SNMP manager application
(Refer to “Using the Configuration Utility” on page 12.) The latest
version may be downloaded from the SMC web site specified on
the back cover of this manual.
The SMC2671W can be configured by a web browser, specifically
Internet Explorer 5.5 or above. Using the web management
interface, you can configure the Wireless Ethernet Adapter and
view statistics to monitor network activity.
Before you attempt to log into the SMC2671W’s web-based
administration, please verify the following.
1. Your browser is configured properly (see below).
2. Disable any firewall or security software that may be running.
3. Confirm that you have a good link LED where your computer
is plugged into the Wireless Ethernet Adapter. If you don’t
have a link light – then try another cable to get a good link.
4. To access the Internet through the Wireless Ethernet Adapter,
you must configure the network settings of the computers on
your LAN to use the same IP subnet as the Wireless Ethernet
Adapter. The default network settings for the Wireless
Ethernet Adapter are:
SMC2671W IP Address: 192.168.2.25
Subnet Mask: 255.255.255.0