SMC Networks SMC-BT10 EZ Connect User manual

Copyright
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and
reliable. However, no responsibility is assumed by SMC for its use, nor for any
infringements of patents or other rights of third parties which may result from its use. No
license is granted by implication or otherwise under any patent or patent rights of SMC.
SMC reserves the right to change specifications at any time without notice.
Copyright © 2004 by
SMC Networks, Inc.
38 Tesla
Irvine, CA 92618
All rights reserved.
Trademarks:
SMC is a registered trademark; and Barricade is a trademark of SMC Networks, Inc.
Other product and company names are trademarks or registered trademarks of their
respective holders.

COMPLIANCES
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance
of 20 centimeters (8 inches) between the radiator and your body. This transmitter must
not be co-located or operating in conjunction with any other antenna or transmitter.
Wireless 2.4 GHz Band Statements:
As the SMC-BT10 Wireless Bluetooth USB Adapter can operate in the 2400-2483 MHz
frequency band it is limited by the FCC, Industry Canada and some other countries to
indoor use only so as to reduce the potential for harmful interference to co-channel
Mobile Satellite systems.
The term “IC:” before the radio certification number only signifies that Industry Canada
technical specifications were met.
Industry Canada – Class B
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus as set out in the interference-causing equipment standard entitled
“Digital Apparatus,” ICES-003 of Industry Canada.
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux
appareils numériques de Classe B prescrites dans la norme sur le matérial brouilleur:
“Appareils Numériques,” NMB-003 édictée par l’Industrie.

EC Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.
The following references have been applied in order to prove presumption of compliance
with the R&TTE Directive 1999/5/EC:
-EN 60950 (2000)
Safety of Information Technology Equipment.
-Council recommendation 1999/519/EC of 12 July 1999, limitations of exposure of the
general public to electromagnetic fields (0 Hz to 300 GHz).
-EN 300 328-1 (2001-12), EN 300 328-2 (2001-12)
-Technical requirements for 2.4 GHz radio equipment.
-EN 301 489-1 (2000-08), EN 301 489-17 (2000-09)
EMC requirements for radio equipment.
Council recommendation 1999/519/EC of 12 July 1999, limitations of exposure of the
general public to electromagnetic fields (0 Hz to 300 GHz)
English Hereby, SMC Networks, declares that this Radio LAN device is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC. The official EC-Declaration of
Conformity can be found under the corresponding product section on
the web http://www.smc.com.
Dutch Hierbij verklaart SMC Networks dat het toestel Radio LAN device in
overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG. Het officiële EC-
gelijkvormigheidattest kan men vinden op de internetsite
http://www.smc.com onder de betrokken productcategorie.
French Par la présente SMC Networks déclare que l'appareil Radio LAN device
est conforme aux exigences essentielles et aux autres dispositions
pertinentes de la directive 1999/5/CE. La déclaration de conformité
officielle peut être trouvée sur notre site internet
http://www.smc.com dans la rubrique Produits.
German Hiermit erklärt SMC Networks, dass sich dieses Wireless LAN Gerät in
Übereinstimmung mit den grundlegenden Anforderungen und den
anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet.
Die offizielle EC-Declaration of Conformity finden Sie im Internet
unter http://www.smc.com unter der entsprechenden
Produktkategorie.
Spanish Por medio de la presente SMC Networks declara que el Radio LAN
device cumple con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva 1999/5/CE. The
official EC-Declaration of Conformity can be found under the
corresponding product section on the web http://www.smc.com.

Countries of Operation & Conditions of Use in EC/ EFTA member states
English This device is a 2.4 GHz wireless LAN transceiver, intended for indoor
home and office use in all notified EC and EFTA member states. In
accordance with article 6.4 of the R&TTE Directive 1999/5/EC the
following EC/ EFTA member states have been notified:
Austria, Belgium, Denmark, Finland, France, Germany, Italy,
Luxembourg, Netherlands, Norway, Spain, Sweden, Switzerland,
United Kingdom, Portugal, Greece, Ireland, Iceland
Requirements for outdoor operation, like license requirements and
allowed channels of operation apply in some countries. Please contact
your local regulation authority or SMC Networks for details on current
restrictions for outdoor use.
Dutch Dit toestel is een 2.4 Ghz draadloze Lan transceiver, bestemd voor
gebruik binnen huis en kantoor in alle geïnformeerde lidstaten van de
EC en de EFTA.
In overeenstemming met artikel 6.4 van de R&T TE Directive
1999/5/EC zijn de volgende EC/EFTA lidstaten verwittigd:
België, Denemarken, Duitsland, Finland, Frankrijk,Griekenland,
Ierland, IJsland, Italië, Luxemburg, Nederland,
Noorwegen,Oostenrijk, Portugal, Spanje , Verenigd Koninkrijk,
Zweden, Zwitserland.
Benodigdheden voor gebruik buiten, zoals gebruiksvergunningen en
toegelaten werkkanalen zijn van toepassing in sommige landen.
Gelieve uw lokale instantie of SMC Networks te contacteren voor
details op huidige beperkingen voor gebruik in buitenlucht.
French Ce produit est un appareil radio LAN transceiver de 2.4 GHz destiné
aux PME et à l’utilisation domestique dans tous les pays certifiés
conformes aux conditions de l’EU et de l’EFTA. En accord avec l’article
6.4 de la R&TTE directive 1999/5/EC, the membres de la EU et de
l’EFTA sont les suivants :
Autriche, Belgique, Danemark, finalnde, France, Allemagne, Italie,
Luxembourg, Pays-Bas, Norvège, Espagne, Suède, Suisse, Royaume-
Uni, Portugal, Grèce, Irelande, Icelande.
Des conditions sont appliquées à certains pays pour l’utilisation en
extérieur, tels que des licences spécífiques et des canaux d’opération.
Veuillez contacter votre autorité locale ou SMC Networks pour plus de
détails quant aux restrictions actuelles concernant l’utilisation en
extérieur.
German Dieses Wireless LAN Gerät arbeitet im 2.4 GHz Frequenzband und ist
für den Einsatz im Innenbereich in den benachrichtigten EC/ EFTA
Mitgliedstaaten geeignet. In Übereinstimmung mit Artikel 6.4 der
R&TTE Direktive 1999/5/EC wurden folgende Mitgliedstaaten
benachrichtigt:
Österreich, Belgien, Dänemark, Finland, Frankreich, Deutschland,
Italien, Luxemburg, Niederlande, Norwegen, Spanien, Schweden,
Schweiz, Großbritannien, Portugal, Griechenland, Irland, Island.

Für den Einsatz im Aussenbereich sind in einigen Ländern Lizenzen
erforderlich oder die Anzahl der Kanäle ist eingeschränkt. Bitte
kontaktieren Sie Ihre Regulierungsbehörde oder SMC Networks für die
aktuellen Einschränkungen beim Einsatz im Aussenbereich.
Spanish Este aparato es un transmisor inalámbrico de 2.4 GHz, previsto para
el uso interior en domicilios y Pymes en todos los Estados de la CE y
la EFTA notificados. De acuerdo con el artículo 6.4 de la Directiva
R&TTE 1999/5/EC los siguientes estados de la CE y de la EFTA han
sido notificados:
Austria, Bélgica, Dinamarca, Finlandia, Francia, Alemania, Italia,
Luxemburgo, Países Bajos, Noruega, España, Suecia, Suiza, Reino
Unido, Portugal, Grecia, Irlanda, Islandia.
Los requisitos para su uso exterior, como requerimiento de licencia y
canales de operación permitidos se aplican en algunos países. Por
favor contacte la autoridad reguladora local o SMC Networks para
más detalles en relación con las restricciones actuales para uso
exterior.
SMC Contact for this device in Europe is:
SMC Networks Europe,
Edificio Conata II,
Calle Fructuos Gelabert 6-8, 2, 4ª,
08970 – Sant Joan Despi,
Barcelona, Spain
Wichtige Sicherheitshinweise (Germany)
1. Bitte lesen Sie diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine
Flüssigoder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur
Reinigung.
4. Die Netzanschlu ßsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder
Fallen könnte Beschädigungen hervorrufen.
7. Die Belüftungsöffnungen dienen der Luftzirkulation, die das Gerät vor Überhitzung
schützt. Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt werden.
8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.
9. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte
auch nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten.
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom
Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung
vermieden.
12.Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das
Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen.

13. Öffnen sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit
nur von authorisiertem Servicepersonal geöffnet werden.

Contents
1BlueSoleil™ Introduction......................................................................... 10
2BlueSoleil™ Graphical User Interface ...................................................... 11
2.1 Start BlueSoleil™ .................................................................................... 11
2.2 Exit BlueSoleil™ ...................................................................................... 11
2.3 BlueSoleil™ Main Window ......................................................................... 12
2.3.1 My Device Icon .................................................................................................................................12
2.3.2 Remote Bluetooth Device Icons ........................................................................................................13
2.3.3 Bluetooth Service Icons ....................................................................................................................14
2.4 Service Window ...................................................................................... 15
2.4.1 My Service Icons ...............................................................................................................................17
3Personal Area Networking....................................................................... 19
3.1 Introduction ........................................................................................... 19
3.2 Connect Two Computers .......................................................................... 19
3.3 Computer with PAN acting as a TCP/IP Gateway .......................................... 25
3.3.1 Connect to the Internet using ICS.....................................................................................................26
3.3.2 Settings on the PAN server ...............................................................................................................27
3.4 PAN Configuration ................................................................................... 29
3.4.1 My PAN Service ................................................................................................................................29
4Dial-Up Networking................................................................................. 30
4.1 Introduction ........................................................................................... 30
4.2 Connect to a Dial-up Gateway from a Computer .......................................... 30
5Bluetooth Serial Port............................................................................... 34
5.1 Introduction ........................................................................................... 34
5.2 Connect Two Computers .......................................................................... 34
5.3 Use SPP to Print a Document .................................................................... 37
5.4 SPP Configuration.................................................................................... 39
5.4.1 My SPP Service.................................................................................................................................39
6Bluetooth File Transfer............................................................................ 40
6.1 Introduction ........................................................................................... 40
6.2 Transfer files to/from a Computer.............................................................. 40
6.3 FTP Configuration.................................................................................... 46
6.3.1 My FTP Service.................................................................................................................................46
7LAN Access ............................................................................................. 47
7.1 Introduction ........................................................................................... 47
7.2 Access a Local Area Network (LAN)............................................................ 47
8Object Push ............................................................................................ 53
8.1 Introduction ........................................................................................... 53
8.2 Transfer Objects from a Computer to a Bluetooth Cellular Phone.................... 53
8.3 Transfer Objects from a Bluetooth Cellular Phone to a Computer.................... 58
8.4 Transfer Objects between Two Computers .................................................. 62
8.5 Configure OPP Service ............................................................................. 63
8.5.1 My OPP Service ................................................................................................................................63
9Synchronization ...................................................................................... 64
9.1 Introduction ........................................................................................... 64

9.2 Exchange PIM Data with a Cellular Phone.................................................... 64
9.3 Set up SYNC Connection between Two Computers........................................ 66
9.4 Synchronization Configuration ................................................................... 70
9.4.1 My Synchronization Service............................................................................................................. 70
10 Hardcopy Cable Replacement ...............................................................71
10.1 Introduction......................................................................................... 71
10.2 Print a Document Using a Bluetooth Printer .............................................. 71
11 Human Interface Device .......................................................................74
11.1 Introduction......................................................................................... 74
11.2 Connect a Computer to a Bluetooth Mouse ............................................... 74
11.3 Connect a Computer to a Bluetooth Keyboard ........................................... 77
12 Connection Shortcut .............................................................................80
12.1 Introduction......................................................................................... 80
12.2 How to use Connection Shortcut ............................................................. 80
13 Bluetooth Glossary ...............................................................................83

1BlueSoleil™Introduction
BlueSoleil™is a Windows-based Bluetooth Wireless software suite from IVT. It is fully
compliant to the latest Bluetooth SIG specifications. BlueSoleil™incorporates Bluetooth
and computer technologies to enable users to wirelessly access computing devices, form
networks, and exchange information.
BlueSoleil™V1.4.9 includes nine Bluetooth profiles. The following table indicates which of
these profiles is available for client and server devices.
Profile Description Client Server
PAN Personal Area Networking √√
SPP Serial Port √√
DUN Dial-Up Networking √
LAP LAN Access √√
FTP File Transfer √√
HID Human Interface Device √
HCRP Hardcopy Cable Replacement √
OPP Object Push √√
SYNC Synchronization √√
BIP Basic Imaging √√
AV AV √√
HS Headset √√
FAX FAX √
BlueSoleil™supports more than ten Bluetooth chip-sets and HCI interfaces including USB,
UART, PCMCIA and Compact Flash.
IVT BlueSoleil™supports:
♦Windows 2000/XP
♦Windows 98SE/Me
This manual describes how to use BlueSoleil™:
♦How to start and exit BlueSoleil™.
♦How to navigate the Main Window and Service Window.
♦How to use the Bluetooth profiles.

2BlueSoleil™ Graphical User Interface
2.1 Start BlueSoleil™
After installing BlueSoleil™, there are two ways to start the program:
1. A BlueSoleil™ shortcut icon on the Windows desktop.
2. An IVT BlueSoleil™program group entry in the Windows’ Start | Programs menu.
Double-click the BlueSoleil™shortcut icon on the desktop or click the BlueSoleil™ menu
item on the Start | Programs | IVT BlueSoleil™menu to start the BlueSoleil™
software.
The BlueSoleil™ icon will be displayed at the bottom right corner of the Windows desktop
(Figure 2.1).
Figure 2.1: BlueSoleil™ icon
The BlueSoleil™Main Window pops up as shown in Figure 2.2.
2.2 Exit BlueSoleil™
To exit BlueSoleil™, right-click the BlueSoleil™ icon at the bottom right corner of the
Windows task bar and select Exit on the pop-up menu.
Note: Selecting the Close button at the top right corner of the BlueSoleil™ window only
hides the BlueSoleil™ window.

2.3 BlueSoleil™ Main Window
The BlueSoleil™ Main Window displays all surrounding Bluetooth devices. From the
BlueSoleil™ Main Window users can search for surrounding Bluetooth devices and can
execute connect/ disconnect functions.
Figure 2.2: BlueSoleil™ Main Window
The main elements in the BlueSoleil™ Main Window are:
♦My Device Icon
♦Remote Bluetooth Device Icons
♦Bluetooth Service Icons
2.3.1 My Device Icon
This icon represents the client computer. It is called the ‘My Device icon’ or ‘center ball’
in this document.
Functions:
3. Hover the mouse over the My Device icon to display the client Bluetooth device name
and address.
4. Double-click to start/ stop searching for surrounding Bluetooth devices.
5. Right-click to display the pop-up menu with related operations.
Remote Device Service
Local Device lcon
Remote Device

2.3.2 Remote Bluetooth Device Icons
The icons in the table below represent the remote Bluetooth devices.
Device Type Icon
Headset
Keyboard
LAN Access Point
Laptop
Mobile
Modem
Mouse
Personal Computer
PDA
Printer
Scanner
Unknown device
The following colors are used to indicate the status of the remote Bluetooth device:

♦White (Idle)
This is the normal status of the device.
♦Yellow (Selected)
The device has been selected by the user.
♦Green (Connected)
The device has been connected.
Functions:
6. Single-click to select.
7. Double-click to get the services remote Bluetooth device supports.
8. Right-click to display the pop-up menu with related operations.
2.3.3 Bluetooth Service Icons
The Bluetooth Service Icons represent the Bluetooth services supported by the remote
device.
Bluetooth Service Icon
Personal Area Networking
Dial-up Networking
Serial Port
LAN Access
File Transfer
Information Synchronization
Object Push
Printer
Human Interface Device
FAX

Basic lmaging
AV
Headset
The following colors are used to indicate the status of the Bluetooth service:
♦White (Idle)
This is the normal status.
♦Pink (Available)
The Bluetooth service is available for the selected device.
♦Yellow (Selected)
The service icon has been selected by the user.
♦Green (Connected)
The service is connected.
Functions:
9. Hover the mouse over the icon to display the service name.
10. Single-click to select the service.
11. Double-click to connect.
12. Click to display the pop-up menu with related operations.
Figure 2.3: Bluetooth PAN Service Icon
2.4 Service Window
Select menu View | Service Window and the Service Window appears.
This window displays the Bluetooth services the ‘my Bluetooth device’ provides to remote
Bluetooth devices. These services are called ‘my Bluetooth services’.

Figure 2.4: BlueSoleil™ Service Window
Main Elements:
♦My Service Icons

2.4.1 My Service Icons
These icons represent ‘my Bluetooth services’.
My Bluetooth Service Icon
Personal Area Networking
Serial Port A
Serial Port B
Object Push
File Transfer
Information Synchronization
LAN Access
AV Headset
Basic Image

Headset AG
The following colors indicate the status of the Bluetooth service:
♦White (Idle)
Normal status.
♦Pink (Started)
My Bluetooth service is started.
♦Green (Connected)
A remote device has connected to my Bluetooth service.
Functions:
13. Single-click to select.
14. Double-click to start/stop a service.
15. Right-click to display the pop-up menu with related operations.

3Personal Area Networking
3.1 Introduction
The Bluetooth Personal Area Networking (PAN) is a Bluetooth application, which enables
devices to form an ad-hoc network or to access a remote network through a network
access point.
The PAN application can be used in the following scenarios:
♦Two or more computers (or PDAs) can be connected through PAN and can
visit each other using Windows Network Places or any application based on
TCP/IP.
♦A computer (or PDA) can access a Local Area Network or the Internet
through a PAN Network Access Point (NAP) bridge.
♦A computer with PAN installed acts as a TCP/IP gateway.
Each of these scenarios is now covered in more detail.
3.2 Connect Two Computers
This section outlines the steps involved in connecting two computers, Computer A and
Computer B.
Computer A: Computer B:
Notebook/ Laptop PIII, 800MHz, 128M Desktop, PIII, 600MHz, 128M
A Bluetooth USB dongle A Bluetooth USB dongle
Windows 2000 Windows 2000
IVT BlueSoleil™ IVT BlueSoleil™
Step 1: Insert Bluetooth USB dongles in both computers.
Step 2: Start BlueSoleil™ in both computers.
Step 3: Set device name of each computer to anything you want. Here they
are named Computer A and Computer B.
♦In the BlueSoleil™ Main Window of Computer A, click Tools |
My Bluetooth Device. Enter ‘Computer A’ in the device name
field in the My Bluetooth Device window.
♦Repeat for Computer B.
Step 4: Set the Security Level.
♦Click Tools | Configurations | Security, the Security
Configuration panel pops up.
♦On the Security Configuration panel, select High in Security
Level.
Note: If you check the Fixed Passkey and input a Bluetooth passkey, this passkey will
be used as the default passkey. The other computer will then have to provide the same
passkey during the connection procedure if it wants to connect to this computer.

Figure 3.1: Security Configuration
Step 5: Start the PAN service on Computer A.
♦In the BlueSoleil™Main Window, click View | Service
Window.
♦In the Service Window, right-click the Personal Area Networking
icon. Choose Start Service. (Figure 3.2)
Figure 3.2: Start PAN Service on Computer A