SMC Networks PB1313A User manual

Doc. no. PAB-OM-O003
Product name
Process pump
Model / Series
PB1313A
SMC Corporation
Operation Manual

－1－
Foreword
Thank you for purchasing SMC’s process pump.
This manual is intended to explain the operation of the product.
This manual will help you to use the product effectively.
Read the operation manual carefully to understand the outline of the product and issues relating to
safety. All instructions noted with “Danger”, “Warning” or “Caution” in this manual have to be
followed.
Handling
●Be sure to read and follow all instructions noted with “Danger”, “Warning” or “Caution” in this manual.
●This manual is intended to explain the installation and operation of the product.
Only people who understand the basic operation of the product through this manual or who
perform installation and operation of or have basic knowledge about industrial machines are
allowed to work on the product.
●It is strictly prohibited to copy this manual entirely or partially for the use by a third party without
prior permission from SMC.
●The product is provided for physical, chemical and industrial equipment. The applicability of this
product for medical applications or other applications requiring the consideration of safety must be
determined by the customer performing safety confirmation testing.

－2－
Contents
Safety Instructions........................................................................................................................3
1. Precautions for system design................................................................................................6
2. Precautions for installation......................................................................................................7
3. Maintenance and check............................................................................................................9
4. Handling Precautions .............................................................................................................10
5. Names and functions of parts................................................................................................10
6. How to use............................................................................................................................... 11
7. Specification and how to order..............................................................................................12
8. Discharge capability...............................................................................................................14
9. Troubleshooting......................................................................................................................16
10. Outer dimensions..................................................................................................................18

－3－
Safety Instructions
These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or
“Danger.”
They are all important notes for safety and must be followed in addition to International Standards
(ISO/IEC)*1), and other safety regulations.
*1) ISO 4414: Pneumatic fluid power -- General rules relating to systems.
ISO 4413: Hydraulic fluid power -- General rules relating to systems.
IEC 60204-1: Safety of machinery -- Electrical equipment of machines .(Part 1: General requirements)
ISO 10218-1992: Manipulating industrial robots -Safety.
etc.
Caution
Caution indicates a hazard with a low level of risk which, if not avoided, could result
in minor or moderate injury.
Warning
Warning indicates a hazard with a medium level of risk which, if not avoided, could
result in death or serious injury.
Danger
Danger indicates a hazard with a high level of risk which, if not avoided, will result
in death or serious injury.
Warning
1. The compatibility of the product is the responsibility of the person who designs the
equipment or decides its specifications.
Since the product specified here is used under various operating conditions, its compatibility with specific
equipment must be decided by the person who designs the equipment or decides its specifications based on
necessary analysis and test results.
The expected performance and safety assurance of the equipment will be the responsibility of the person who
has determined its compatibility with the product.
This person should also continuously review all specifications of the product referring to its latest catalog
information, with a view to giving due consideration to any possibility of equipment failure when configuring the
equipment.
2. Only personnel with appropriate training should operate machinery and equipment.
The product specified here may become unsafe if handled incorrectly.
The assembly, operation and maintenance of machines or equipment including our products must be
performed by an operator who is appropriately trained and experienced.
3. Do not service or attempt to remove product and machinery/equipment until safety is
confirmed.
1.The inspection and maintenance of machinery/equipment should only be performed after measures to
prevent falling or runaway of the driven objects have been confirmed.
2.When the product is to be removed, confirm that the safety measures as mentioned above are implemented
and the power from any appropriate source is cut, and read and understand the specific product precautions
of all relevant products carefully.
3. Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.
4. Contact SMC beforehand and take special consideration of safety measures if the product is
to be used in any of the following conditions.
1. Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to
direct sunlight.
2. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,
vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and
beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or
other applications unsuitable for the standard specifications described in the product catalog.
3. An application which could have negative effects on people, property, or animals requiring special safety
analysis.
4.Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a
mechanical protective function, and periodical checks to confirm proper operation.

－4－
Safety Instructions
Caution
1.The product is provided for use in manufacturing industries.
The product herein described is basically provided for peaceful use in manufacturing industries.
If considering using the product in other industries, consult SMC beforehand and exchange
specifications or a contract if necessary.
If anything is unclear, contact your nearest sales branch.
Limited warranty and Disclaimer/Compliance Requirements
The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance
Requirements”.
Read and accept them before using the product.
Limited warranty and Disclaimer
1. The warranty period of the product is 1 year in service or 1.5 years after the product is
delivered, whichever is first.2)
Also, the product may have specified durability, running distance or replacement parts.
Please
consult your nearest sales branch.
2. For any failure or damage reported within the warranty period which is clearly our
responsibility,
a replacement product or necessary parts will be provided.
This limited warranty applies only to our product independently, and not to any other damage
incurred due to the failure of the product.
3. Prior to using SMC products, please read and understand the warranty terms and
disclaimers
noted in the specified catalog for the particular products.
2) Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to the use of the vacuum
pad or failure due to the deterioration of rubber material are not covered by the limited
warranty.
Compliance Requirements
1. The use of SMC products with production equipment for the manufacture of weapons of
mass destruction (WMD) or any other weapon is strictly prohibited.
2. The exports of SMC products or technology from one country to another are governed by
the relevant security laws and regulations of the countries involved in the transaction. Prior
to the shipment of a SMC product to another country, assure that all local rules governing
that export are known and followed.

－5－
Do not touch.
Sign warning of possible injury by touching the product surface with hazardous fluid on it, or when
the product is hot.
Fluid leakage
Warning of external leakage of circulating fluid.
Warning related to corrosion
Warning indicating risk of chemical corrosion
Read and understand the Material Safety Data Sheet (MSDS) carefully before using the product,
and use appropriate protective equipment.
Warning related to inhalation
This symbol indicates a possible risk of inhalation of chemicals
This symbol indicates that serious injury can result from exposure to the atmosphere or inhalation.
Read and understand the Material Safety Data Sheet (MSDS) carefully before using the product,
and use appropriate protective equipment (e.g. goggles).

－6－
1. Precautions for system design
Warning
(1)Confirm the specifications.
Fully understand the applications, fluids, environment and other operating conditions to use this
product within the specified range shown in this operation manual.
(2)Applicable fluids
●If the fluid contains foreign matter, the inside of the pump will become worn out , causing
problems. Eliminate the foreign matter by using an appropriate filter (strainer).As a guide, the
appropriate filtration is 80 to 100 mesh (150 to 180mm).
●When circulating coagulable fluids, handle them carefully so that they do not coagulate in the
pump.
●Use caution so that the operating fluid does not adhere to the product outer surface.Never use
the product with the operating fluid adhering to the product outer surface.
(3)Water hammer
Sudden operation of the valve may create high pressure due to water hammer.Take measures so
that pressure exceeding the specification value is not applied.
<Countermeasures>
●Reduce the opening speed of the valve by using a water hammer cushioning valve.
●Use a material for piping such as a rubber hose or an accumulator to absorb the impact
pressure.
(4)Liquid-sealed circuit
Mount a by-pass valve to the system so that it does not
form a liquid-sealed circuit. (Figure on the right)
(5)Fluid pressure
Feeding the fluid from the suction side into the pump with pressure or drawing it with negative
pressure will cause reverse pressure to be applied to the diaphragm and the check valve, causing
shortening of the product life.
(6)Provide enough space for maintenance.
Allow sufficient space for maintenance and inspection.
(7)Provide safety measures against fluid leakage.
Take fluid leakage of the product into consideration when using. When transferring flammable
fluids or fluids which affect the human body and environment, take measures such as prohibiting
ignition sources, and prohibiting entry to the operation area. External leakage of pumping fluid
could cause serious injury.
(8)Design the circuit so that reverse flow and reverse pressure are prevented.
Reverse flow or reverse pressure may lead to damage to equipment and operation failure. Take
safety measures when designing the circuit. When installing a check valve, use the check valve
whose cracking pressure is 0.02MPa or less. Using the check valve of higher cracking pressure,
suction failure might be occurred.
Countermeasure against
liquid-sealed circuit
Relief valve
Pump

－7－
(9)Countermeasures against static electricity
Since static electricity may be generated depending on the fluid being used, implement suitable
countermeasures.
(10)The pump cannot transfer gas. Do not allow it to idle for a long time.
If the pump is operated for a long time without any fluid inside, the diaphragm may be damaged or
the life may be shortened. Do not continue idling longer than 3 minutes.
(11)Pilot port condensation and freezing
Condensation may form in the piping of the AIR SUP port, due to sudden cooling because of the
expansion of supply air. The fluid may freeze in winter. Measures should be taken so that the
electrical parts and equipment do not get wet due to dripping.
Caution
(1)Operation stop of the pump
When the operation of the pump is stopped, be sure to exhaust the residual pressure in the pump.
When operating this pump, please use a 3-port normally closed (N.C.) solenoid valve to
completely exhaust the residual pressure.
(2) Slurry cannot be transferred.
Slurry cannot be transferred due to seating failure and wearing of the check valve and
accumulation of particles causing operation failure.
2. Precautions for installation
Warning
(1)Use clean air.
1. Do not use compressed air which contains chemicals, synthetic oils containing organic
solvents, salts or corrosive gases, etc., as this can cause damage or malfunction.
2. The quality of the compressed air used should correspond to system No. C to F in Best
Pneumatics (5)(P.2 to 3).
(Install a filter with filtration accuracy of 5m. If necessary, install a mist separator with the filter.)
3. Supply air which has been dried by an air dryer.
(Recommended atmospheric dew point is -10oC or less.)
4. Supply air in the range of 0.2 to 0.5MPa with sufficient supply capacity.
(2)When the process pump is used under low temperature, beware of freezing.
The equipment operates by expanding compressed air. During adiabatic expansion, the temperature
inside of the product goes down. When the ambient temperature is low, heat cannot be obtained from
the surrounding environment. Freezing can result if compressed air containing moisture is used. In
this case, the membrane air dryer (IDG etc.) is recommended to prevent freezing.

－8－
(3)Do not use in the following environments.
1. An environment where corrosive gases, organic solvents, chemicals, or flammable fluidsarepresent.
2. Where the product is exposed to sea water, water, or water vapor.
3. Where the deterioration of the resin due to ultraviolet or temperature rise is possible because of
direct sunlight.
4. Where a heat source is present in the surrounding environment and ventilation is poor (shield
the heat source with an insulator).
5. Where impact or vibration is present.
6. Where excess humidity or dust is present.
(4)Compressed air at low dew point
If ultra dry air is used as pilot air, it can reduce the lubrication characteristics and affect the
reliability (life) of the equipment. Contact SMC beforehand.
(5)Mounting of the pump:
Mount the pump securely with four M4 bolts.
(6)Caution for piping of the tube
Support the piping according to JIS B 8370 when piping the tube. Arrange the piping so that
tension is not applied to the tube.
Caution
(1) Assemble after reading the operation manual.
Mount the product after reading the operation manual carefully. Also keep it available whenever
necessary.
(2)Check the mounting direction of the product.
Mount the product vertically so that the FLUID OUT port faces upward. Otherwise internal parts
will not operate smoothly to achieve the full performance.
Secure all mounting parts properly. If the transmission of vibration is unacceptable, insert an
isolating rubber material before installation.
(3)Flush the piping before installing.
Flush and clean the piping before installing the product. Dust and foreign matter left in the piping
can cause operating failure and malfunction.
(4)If fittings with metal threads are used, it could break the female thread of the product. For
piping the tube fitting, use fittings with resin threads.
(5)Observe the tightening torque for screws.
When screwing fittings into the product, tighten them with proper tightening torque as shown
below. Over-tightening can damage the thread.
PB1313A series
Thread size
Proper tightening torque
Rc,NPT,G 1/8
1.5 to 2.0 N･m
M10
0.8 to 1.0N･m

－9－
3. Maintenance and check
Warning
(1)The following points must be carefully considered for maintenance
Maintenance shall be performed after obtaining adequate knowledge about the product by
reading this operation manual carefully. Improper handling can cause damage and malfunction
of equipment and machinery.
●When touching the pump for maintenance, wear protective gear such as gloves
which are compatible with the fluid used. There is a risk of chemical burns.
●If the pump is stopped for a few hours, exhaust the air from theAIR SUP port.
●During operation of the pump, it is necessary to check air leakage and operating
conditions regularly. If any abnormality is seen, stop operating the product and
contact your local supplier or SMC sales representative.
(2)Confirm safety before operation
When the product or the supply/exhaust equipment of the pilot air is removed, cut the supply of
compressed air and power, then exhaust compressed air from the system. Discharge or substitute
the residual fluid if necessary. When the equipment is to be started again after remounting or
replacement, first confirm safety, and then confirm that the equipment can operate normally.
(3)Do not disassemble the product. Disassembled product is not guaranteed.
If overhaul is required, contact SMC or the distributor.
(4)Discharging condensate
Operation with condensate caught in the equipment or the piping may lead to operation failure of
the equipment, splashing from the outlet, and unexpected accidents. Remove condensate from
air filters regularly.
Caution
(1)Life of the diaphragm
●When the operation time of the diaphragm exceeds its life, the process pump may be damaged
because the diaphragm is deformed. If the process pump is damaged, the operating fluid will
leak from the pilot air exhaust port and air will get into the fluid circuit. Replace the pump
considering the operating condition of the pump (irregular intake of air, reduction of discharge
pressure) and the reference life of the diaphragm.
[Calculation method of the diaphragm life for reference]
Calculate the life based on the operation frequency of the solenoid valve.
Reference life (day) =
A: Reference life (time)
Operating frequency of the solenoid valve (Hz) x operating time per day (hour)
x 60 (min.) x 60 (sec.)
Model
How to operate
Reference life (time) A
The discharge for one cycle.
PB1313A
Air operated type
50 million times
Approx. 3mlNote1)
Note1) This is not a metering pump. The amount of discharge depends on the operating condition.

－10－
4. Handling Precautions
Warning
(1)Perform testing before the actual operation.
Verify with the actual equipment used with this product. Even if the test over a short period shows
no problem, it may cause a malfunction depending on the components of the fluid.
(2)Storage
When the product is stored for a long period of time after usage, remove the fluid completely from
the pump before storage to prevent sticking and deterioration of the pump material.
(3)When not used for extended periods of time, perform trial run before use.
(4)Operating environment
When dangerous fluid is used, take measures to isolate humans from the pump. External leakage
of pumping fluid could cause serious injury.
(5)Countermeasures against liquid leakage
There are some cases where the operating fluid will leak outside the pump, for example when the
diaphragm reaches the end of the life. Measures should be taken to avoid leakage, such as
installing a drain pan, so that people and equipment will not be adversary affected.
Caution
(1)Operating temperature
The pump can be used within the range from 0 to 50oC. Do not let it freeze.
5. Names and functions of parts
Description
Functions
Suction port (FLUID IN)
Sucks the fluid to be transferred. Connect suction piping.
Discharge port (FLUID OUT)
Discharges the fluid taken in the pump. Connect discharge piping.
Air supply port (AIR SUP)
Supplies air of set pressure. Connect the air piping.
Air supply port
Discharge port
Suction port

－11－
6. How to use
1)Start and stop
(1) Connect air piping to air supply port ”AIR SUP”, and fluid transfer piping to suction port
“FLUID IN” and discharge port ”FLUID OUT”.
3-port solenoid valve (N.C) needs to be prepared separately to turn ON and OFF the pilot air
which is supplied to the air supply port.
(2) Set pilot air pressure within the range 0.2 to 0.5MPa.
Start operation byapplying ON/OFF signal repeatedly to the solenoid valve prepared separately.
After a while, the fluid will flow from the suction port “FLUID IN” to the exhaust port “FLUID OUT”.
It sucks by itself without priming. (Suction pump head : 0.5m Normal temp. / clean water)
(3) To stop the pump, stop the solenoid valve, and make sure to exhaust all the air inside the pump.
Although the pump is stopped by closing the valve installed at the discharge side, avoid stopping
operation for a long time in this way.
If the valve closes suddenly, surge is generated, shortening the pump life.
2) Adjustment of the discharge amount (Typical circuit )
(1) The flow rate changes by changing the switching time (Operation cycle) of the solenoid valve
ON/OFF signal.
(2) Use the ball valve connected to the discharge side to adjust the flow at the fluid side.
(3) When exhausting air, using a meter-out will reduce the suction speed of the fluid and so
reduce the generation of bubbles.
ｃ
ｃ
Meter-out
PB1313A
Filter
Pressure regulator
Circuit example
FLUID IN
Solenoid
valve
ON/OFF signal
Ball valve
FLUID
OUT
Air supply source

－12－
7. Specification and how to order
●Specifications
Model
PB1313A
Type of operation
Air operated type
Port size
Main fluid
Suction/discharge port
Rc,NPT,G 1/8 Female thread, 1/4” PFA tube,
LQ1 size 2 with nuts, LQ3 size 2 with nuts
Pilot air
Supply / Exhaust port
Rc,NPT,G 1/8 Female thread
Material
Body wetted areas
New PFA
Diaphragm
PTFE
Check valve
New PFA、PTFE
Liquid contact seals
PTFE
Maximum discharge rate
1000mL/minNote1)
Average discharge pressurer
0 to 0.4MPa
Pilot air pressure
0.2 to 0.5MPa
Air consumption
15L/min(ANR) or less
Suction head
Up to 0.5m
Noise
71dB(A) or less
Withstand pressure
0.75MPa
Diaphragm life (Reference)
50 million times (One time per cycle)
Operating fluid temperature
0 to 50℃(No freezing, heat cycle is not applied)
Ambient temperature
0 to 50℃(No freezing, heat cycle is not applied)
Recommended operating cycle
1 to 5Hz
Pilot air solenoid valve recommended Cv factor
0.2Note2)
Weight
0.3 kg
Mounting orientation
FLUID OUT port at top
Maximum operating viscosity
100mPa・s
Packaging environment
Double clean packaging
The values above are at normal temperature and with clean water.
Note 1) When the piping length of both the suction side and the discharge side is almost 0m.
It may not be possible to obtain the discharge in the specification depending on the piping
conditions. With the air operated type, it may not be possible to obtain the discharge in the
specification depending on the piping conditions for the pilot air.
Note 2) Operation is possible with a valve with small Cv value when the operation cycle is small.

－13－
●How to Order
PB1 3 1 3 A S -
Material of diaphragm ●
Symbol
Material of diaphragm
1
PTFE
Actuation ●
Symbol
Actuation
3
Air operated
Female thread /
Tube extension
With nut
PB1313 A S-
●Port size
Symbol
Main fluid
connection size
Pilot air
connection size
Female thread
01
Rc 1/8
N01
NPT 1/8
F01
G 1/8
Tube extension
P07
With 1/4" tubing
Rc 1/8
P07N
NPT 1/8
P07F
G 1/8
With nut
1S07
LQ1 size 2 with
nuts
Rc 1/8
1S07N
NPT 1/8
1S07F
G 1/8
3S07
LQ3 size 2 with
nuts
Rc 1/8
3S07N
NPT 1/8
3S07F
G 1/8
Connection method ●
Symbol
Connection method
S
With nutNote）
Note) The nut is a space saving
type.

－14－
8. Discharge capability
1) Flow-rate characteristics
Caution
-The above flow characteristic graph is for clean water (viscosity 1mPa･s, specific gravity 1.0).
If a fluid with higher viscosity such as oil is used, convert the fluid to clean water with reference
to the viscosity characteristic graph.
-The discharge rate is affected by the characteristics of the transported fluid (viscosity, specific
gravity) and operating conditions (temperature, pump head, transporting distance). When
using the pump, select a pump with adequate capacity for the specification of the device.
-In an application where back pressure is applied from the discharge port “FLUID OUT”, the
result of (pilot air pressure - back pressure) is the pilot air pressure on the graph. Also, it
should be noted that the discharge rate will be less than the normal condition.
2) Air consumption
-If the compressor output is selected
based on air consumption, 0.75kW
per 100L/min(ANR) is the guide.
エア消費量
0
2
4
6
8
10
12
14
16
1 2 3 4 5
サイクル（Hz）
エア消費量（L/min[ANR]）
SUP=0.5MPa
SUP=0.35MPa
SUP=0.2MPa
Air consumption
Cycle (Hz)
Air consumption (L/min [ANR])
Caution
PB1313A流量特性（5Hz作動時）
0
0.1
0.2
0.3
0.4
0.5
0200 400 600 800 1000
吐出量 （mL/min）
吐出圧力 （MPa）
SUP=0.5MPa
SUP=0.4MPa
SUP=0.3MPa
SUP=0.2MPa
Discharge pressure (MPa)
Discharge rate (mL/min)
PB1313A Flow-rate characteristics (5Hz)

－15－
3) Viscosity characteristics
With reference to the viscosity characteristic graph (shown below), discharge amount of
transported fluid with higher viscosity can be calculated.
●How to calculate the pilot air pressure and consumed air flow
< Example of required specifications >
-Discharge : 200mL/min -Discharge pressure : 0.2MPa -Viscosity : 15mPa･s
-Solenoid valve cycle : Calculate the pilot air pressure and consumed air flow at 5Hz
1．First, check the ratio of discharge amount to clean water from the graph above when the
viscosity is 15mPa･s.
From the graph it is approx. 40%.
2．Next, convert it to discharge rate of clean water.
40% of the discharge of clean water corresponds to 200mL/min. of required specification.
Therefore 200mL/min / 0.40 = approx. 500mL/min, meaning that 500mL/min. of
discharge is necessary for clean water.
3．According to the flow characteristic graph, mark the intersection of discharge pressure
0.2Mpa and discharge amount 500mL/min.
The intersection shows that the pilot air pressure is approx. 0.35MPa.
4．Based on the air consumption graph, mark the point of pilot air pressure of 0.35MPa.
From this point, air consumption is approx. 10.5L/min[ANR].
清水に対する吐出量の比率（％）
粘度（ｍＰａ・ｓ）
Ratio of discharge to clean water (%)
Viscosity (mPa･s)

－16－
Caution
-The graph of flow-rate characteristics is in the condition of no piping for suction and discharge.
It may not be possible to obtain the discharge in the graph depending on the piping conditions.
In air operated type, the discharge is greatly affected by the piping conditions of pilot air.
-The viscosity of the operating fluid depends on the operating conditions (temperature,
transportation distance).
The viscosity can also vary due to changes in the ambient temperature.
-Fluids of viscosity up to 100 mPa･s can be used.
9. Troubleshooting
If any abnormality is found, perform checks according to the following list. If the abnormality
cannot be eliminated, ask SMC.
Warning
-Discharge dangerous fluid from the pump.
-Do not return the pump with dangerous fluid left in it. Otherwise, the fluid could cause burns
and other injuries during transportation. If the product is to be returned, inform SMC or the
distributor beforehand.
Trouble
Possible cause
Remedy
1)Supply of air cannot move
the pump.
-Operation failure of the solenoid valve.
-Replace the solenoid valve
with a new one.
2)The pump
starts, but
does not
discharge
fluid.
The pump
does not
suck fluid.
-The check valve is clogged.
-The check valve is damaged or worn out.
-The filter at suction side (IN port) is
clogged.
-Excessive suction pump head.
-Incorrect mounting direction.
-The diaphragm is damaged or coming
off.
-Sealing failure of fitting at suction side
(IN port).
-Excessive viscosity of transported fluid.
-Cleaning
-Replace the pump.
-Clean the filter.
-Reduce within self suction
capacity.
-Correct to normal mounting
direction.
-Replace the pump.
-Ensure sufficient sealing.
-Non-conformance.
The pump
sucks, but
does not
discharge.
-Check valve or fitting at discharge side
(OUT port) is clogged.
-Cleaning

－17－
3)The discharge amount is
insufficient.
-Check valve at suction side (IN port) or
discharge side (OUT port) is clogged.
-Excessive viscosity of transported fluid.
-Large suction or discharge pump head.
-The filter of suction side (IN port) is
clogged.
-The filter of discharge side (OUT port) is
clogged.
-Insufficient air supply.
-Too small port size of transported fluid
piping.
-Back pressure is applied from the
discharge side (OUT port).
-Cleaning
-Non-conformance
-Reduce the pump head.
-Clean or replace the filter.
-Clean or replace the filter.
-Supply air at adequate
pressure.
-Increase the air supply.
-Remove the back pressure or
increase the air supply
pressure.
4)A lot of air bubbles come
out from the discharge
side (OUT port).
-Air is sucked from the suction side (IN
port).
-Sealing failure of fitting at suction side
(IN port).
-Damaged diaphragm
-Prevent suction.
-Ensure sufficient sealing.
-Replace the pump.
5)Transported fluid flows
out from exhaust port.
(EXH port)
-Damaged diaphragm
-Replace the pump.
6)Transported fluid or air
leaks from jointed part to
outside.
-Damaged diaphragm
-Swelling, contraction, and deterioration
of the sealing.
-Excess supply air pressure
-Replace the pump.
-Replace the pump.
-Supply air at appropriate
pressure.

－18－
10. Outer dimensions

－19－
Revision history
4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN
Tel: + 81 3 5207 8249 Fax: [phone]
URL http://www.smcworld.com
Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.
© 2013 SMC Corporation All Rights Reserved
付表 2 5/5