SMC Networks Barricade SMC7004VBR User manual

Cable/DSL Broadband Router
Built-in 4-Port 10/100Mbps Switch
USER GUIDE
SMC7004VBR

7004VBR –Manual
2
Copyright
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However,
no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights
of third parties which may result from its use. No license is granted by implication or otherwise under
any patent or patent rights of SMC. SMC reserves the right to change specifications at any time
without notice.
Copyright © 2003 by
SMC Networks, Inc.
38 Tesla
Irvine, CA 92618
All rights reserved.
Trademarks:
SMC is a registered trademark; and Barricade is a trademark of SMC Networks, Inc. Other product
and company names are trademarks or registered trademarks of their respective holders.

7004VBR –Manual
3
TABLE OF CONTENTS
CHAPTER 1 | Introduction
Features and Benefits
Package Contents
Minimum Requirements
CHAPTER 2 | Getting to know the Barricade
LED Indicators
Resetting the Barricade
CHAPTER 3 | Getting Connected
Basic Installation Procedure
3-click Installation Wizard
CHAPTER 4 | Configuring your Computer
Configuring Windows 95/98/Me
Configuring Windows 2000
Configuring Windows XP
Configuring a Macintosh Computer
CHAPTER 5 | Configuring the Barricade
Browser Configuration
Disable Proxy Connection
Accessing the Barricade Management
Navigating the Web-based Administration
Making Configuration Changes
Setup Wizard
Advanced Setup
Chapter 7 | Setting up the Print Server
Install the SMC Printer Port Monitor
Configure the Print Server using the SMC Printer Port Monitor
Configure LPR port on Windows 2000/XP
Confirm printer Connection
APPENDIX A | Troubleshooting
APPENDIX B | Technical Specifications
APPENDIX C | Warranty
APPENDIX D | Compliances
APPENDIX E | Technical Support

7004VBR –Manual
4
CHAPTER 1 | Introduction
Congratulations on your purchase of a Barricade™ Cable/DSL Broadband Router (SMC7004VBR).
SMC is proud to provide you with a powerful yet simple communication device for connecting your
local area network (LAN) to the Internet.
1.0 | Features and Benefits
•EZ 3-Click Installation Wizard -A new and improved way to install your Barricade. In 3
simple clicks, you will be connected to the Internet.
•Internet connection to DSL or cable modem via a 10/100 Mbps WAN port
•Local network connection via 10/100 Mbps Ethernet switch ports
•DHCP for dynamic IP configuration, and DNS for domain name mapping
•Firewall with Stateful Packet Inspection, client privileges, hacker prevention, DoS, and NAT
•NAT also enables multi-user access with a single-user account, and virtual server
functionality (providing protected access to Internet services such as web, mail, FTP, and
Telnet)
•Virtual Private Network support using PPTP, L2TP, or IPSec pass-through
•User-definable application sensing tunnel supports applications requiring multiple connections
•Parental controls allows the user to block access to certain web sites
•Email alerts when the users network is being compromised
•Easy setup through a web browser on any operating system that supports TCP/IP
•Compatible with all popular Internet applications
1.1 | Package Contents
Before installing the Barricade™ Cable/DSL Broadband Router, verify that you have the items listed
under “Package Contents.” Also be sure that you have the necessary cabling. If any of the items are
missing or damaged, contact your local SMC distributor.
•Barricade Broadband Router
•Power adapter
•One CAT-5 Ethernet cable
•Four rubber feet
•CD with User Guide and EZ 3-Click Installation Wizard
•Quick Installation Guide
If possible, retain the carton and original packing materials in case there is a need to return the
product.
1.2 | Minimum Requirements
•Cable or DSL Modem with Ethernet connection and Internet access from your local telephone
company or Internet Service Provider (ISP) using a DSL modem or cable modem.
•A computer equipped with a 10 Mbps, 100 Mbps, or 10/100 Mbps Fast Ethernet card, or
USB-to-Ethernet converter.
•Network adapter with Ethernet (UTP CAT 5) cabling and TCP/IP protocol installed per PC
•Internet Explorer 4.0 (or Higher) or Netscape Navigator 4.7 (or Higher) for Web-based
configuration of the Barricade

7004VBR –Manual
5
CHAPTER 2 | Getting to Know the Barricade
The SMC7004VBR Barricade Cable/DSL Broadband Router is the perfect solution for the home/office
environment. This full-featured router offers:
•4 -10/100 Mbps Auto-Sensing LAN ports with Auto-MDI MDIX feature
•1 -10/100 Mbps WAN port with Auto-MDI MDIX feature
•Comprehensive LEDs for network status and troubleshooting
•Reset Button
2.1 | LED Indicators
The Barricade includes LED indicators on the front panel that simplify installation and network
troubleshooting.
LED ON OFF FLASHING
POWER Receiving power Not receiving power N/A
WAN Good WAN connection
detected No WAN connection detected Transmitting or receiving traffic
LINK/ACT Good LAN connection
detected No LAN connection detected Transmitting or receiving traffic
10/100 Mbps LAN port operating at
100 Mbps LAN port operating at 10 Mbps N/A
Resetting the Barricade
The Reset button is located on the rear panel of the Barricade Broadband Router. Use a paper clip or
a pencil tip to push the Reset button.
Reset
If the Router is having problems connecting to the Internet, simply unplug the router for 3 seconds
then plug back in.
Restore Factory Defaults
If resetting the router does not resolve your issue, then you can follow these steps:
1. Leave power plugged into the router
2. Locate the reset button on the back panel, press and hold until WAN LED flashes off.
3. Release reset button.

7004VBR –Manual
6
CHAPTER 3 | Getting Connected
The SMC7004VBR Barricade Cable/DSL Broadband router is connected between the Cable/DSL
Broadband Modem and your computers. If you have more then one computer to connect, simply
plug the other computers into the LAN ports on the back of the router.
3.1 | Basic Installation Procedure
1. Connect the LAN
Run an Ethernet cable from one of the LAN ports on the back of the Barricade to your
computer’s network adapter.
2. Connect the WAN
Connect an Ethernet cable from your cable or DSL modem to the Barricade’s WAN port on
the back on the router.
3. Power on
Connect the power cable to the Barricade.
Once you have completed connecting all of the hardware, simply insert the Barricade CD-ROM and
the EZ 3-Click Installation Wizard will automatically connect you to the Internet.
For manual configuration of the PCs, see Chapter 4.
For advanced configuration of the Barricade Broadband Router, see Chapter 5.
MODEM
COMPUTER

7004VBR –Manual
7
CHAPTER 4 | Configuring your Computer
The information outlined in this chapter will guide you through the configuration for the following
Operating Systems:
•Windows 95/98
•Windows Me
•Windows 2000
•Windows XP
•Apple Macintosh
4.1 | Configuring Windows 95/98/Me
1. Access your Network settings by clicking [Start], choose [Settings], and then select [Control
Panel].
2. In the Control Panel, locate and double-click the [Network] icon.
3. Highlight the TCP/IP line that has been assigned to your network card on the [Configuration]
tab of the [Network] properties window.
4. Next, click the [Properties] button to view that adapter’s TCP/IP settings.

7004VBR –Manual
8
5. From the TCP/IP Properties dialog box, click the [Obtain an IP address automatically] option.
6. Next click on the [Gateway] tab and verify the Gateway field is blank. If there are IP
addresses listed in the Gateway section, highlight each one and click [Remove] until the
section is empty.
7. Click the [OK] button to close the TCP/IP Properties window.
8. On the Network Properties Window, click the [OK] button to save these new changes.
NOTE: Windows may ask you for the original Windows installation disk or additional files.
Check for the files at c:\windows\options\cabs, or insert your Windows CD-ROM into your
CD-ROM drive and check the correct file location, for example, D:\win98, D:\win9x. (assume
“D” is your CD-ROM drive).
9. Windows may prompt you to restart the PC. If so, click the [Yes] button. If Windows does
not prompt you to restart your computer, do so anyways to ensure your settings.
4.2 | Configuring Windows 2000
1. Access your Network settings by clicking [Start], choose [Settings], and then select [Control
Panel]
2. In the Control Panel, locate and double-click the [Network and Dial-up Connections] icon
3. Locate and double-click the [Local Area Connection] icon for the Ethernet adapter that is
connected to the Barricade. When the Status dialog box window opens, click the [Properties]
button.
4. On the [Local Area Connection] Properties box, verify the box next to Internet Protocol
(TCP/IP) is checked. Then highlight the Internet Protocol (TCP/IP), and click the Properties
button.
5. Select Obtain an IP address automatically to configure your computer for DHCP. Click the
[OK] button to save this change and close the Properties window.
6. Click the [OK] button again to save these new changes.
7. Reboot your PC.

7004VBR –Manual
9
4.3 | Configuring Windows XP
The following instructions assume you are running Windows XP with the default interface. If you are
using the Classic interface (where the icons and menus look like previous Windows versions), please
follow the instructions for Windows 2000 outlined above.
1. Access your Network settings by clicking [Start], choose [Control Panel], select [Network and
Internet Connections] and then click on the [Network Connections] icon.
2. Locate and double-click the Local Area Connection icon for the Ethernet adapter that is
connected to the Barricade Router. Next, click the [Properties] button.
3. On the [Local Area Connection] Properties box, verify the box next to Internet Protocol
(TCP/IP) is checked. Then highlight the Internet Protocol (TCP/IP), and click the Properties
button.
4. Select Obtain an IP address automatically to configure your computer for DHCP. Click the
[OK] button to save this change and close the Properties window.
5. Click the [OK] button again to save these new changes.
6. Reboot your PC.
4.4 | Configuring a Macintosh Computer
You may find that the instructions here do not exactly match your screen. This is because these
steps and screenshots were created using Mac OS 8.5. Mac OS 7.x and above are all very similar, but
may not be identical to Mac OS 8.5.
1. Pull down the Apple Menu. Click [Control Panel] and select TCP/IP.
2. In the TCP/IP dialog box, make sure that [Ethernet] is selected in the [Connect Via:] field.
If [Using DHCP Server] is already selected in the [Configure] field, your computer is already
configured for DHCP. Close the TCP/IP dialog box, and skip to Step 2 Disable HTTP Proxy
(bottom of this page).
3. All the information that you need to record is on the [TCP/IP] dialog box. Use the space
below to record the information.
4. Select [Using DHCP Server] in the [Configure] field and close the window.
5. Another box will appear asking whether you want to save your TCP/IP settings. Click [Save].

7004VBR –Manual
10
CHAPTER 5 | Configuring the Barricade
After you have configured TCP/IP on a client computer, use a web browser to configure the
Barricade™ Broadband Router. The Barricade can be configured by any Java-supported browser
including Internet Explorer 4.0 or above, or Netscape Navigator 4.7 or above. Using the web
management interface, you may configure the Barricade and view statistics to monitor network
activity.
Before you attempt to log into the Barricade’s Web-based Administration, please verify the following:
1. Your browser is configured properly. (see below)
2. Disable any firewall or security software that may be running.
3. Confirm that you have a good “link” LED where your computer is plugged into the Barricade.
If you don’t have a “link” light, try another cable until you get a good link.
5.1 | Browser Configuration
Confirm your browser is configured for a direct connection to the Internet using the Ethernet cable that
is installed in the computer. This is configured through the options/preference section of your browser.
5.2 | Disable Proxy Connection
You will also need to verify that the “HTTP Proxy” feature of your web browser is disabled. This is so
that your web browser will be able to view the Barricade configuration pages. The following steps are
for Internet Explorer and for Netscape. Determine which browser you use and follow the appropriate
steps.
Internet Explorer (5 or above)
1. Open Internet Explorer. Click [Tools], and then select [Internet Options].
2. In the [Internet Options] window, click the [Connections] tab.
3. Click the [LAN Settings] button.
4. Clear all the check boxes and click [OK] to save these LAN settings changes.
5. Click [OK] again to close the [Internet Options] window.
Netscape (4 or above)
1. Open Netscape. Click [Edit], and then select [Preferences].
2. In the [Preferences] window, under [Category], double-click [Advanced], then select the
[Proxies] option.
3. Check [Direct connection to the Internet].
4. Click the [OK] button to save the changes.
NOTE: Before you attempt to configure your router, if you have access to the Internet
please visit www.smc.com and download the latest firmware update.