SMC Networks Barricade SMCWBR14T-G User manual

SMCWBR14T-G
SMCWBR14T-G 802.11g 108Mbps
Wireless Barricade™ Router
Model Number: SMCWBR14T-G
Quick Installation Guide
Installationskurzanleitung
Guide d’installation rapide
Manual de instalación rápida
Snabbinstallationshandbok
Beknopte installatiehandleiding
Manual de Instalação Rápida
802.11g 108Mbps Wireless Barricade™ Router
802.11g 108 Mbit/s Wireless Barricade™ Router
Routeur Barricade™ sans fil 802.11g 108Mbps
Barricade™ Router inalámbrico 802.11g de 108 Mbps
802.11g 108Mbit/s trådlös Barricade™-router
802.11g 108Mbps Wireless Barricade™ Router
Router Sem Fios de 108 Mbps 802.11g Barricade™
SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 1

1
English
2
Contents
After unpacking the SMCWBR14T-G Router, please check the
contents of the box to be sure you have received the following
components:
•One Barricade™ SMCWBR14T-G 802.11g Wireless Router.
•One Power Adaptor.
•One Ethernet Cable.
•One CD-ROM.
Immediately inform your dealer in the event of any incorrect,
missing or damaged parts. If possible, please retain the carton
and original packing materials in case there is a need to return
the product.
Please register this product and upgrade the product warranty
at SMC's Web site: www.smc.com.
Package Contents
English 2-13
Deutsch 14-25
Français 26-37
Español 38-49
Svenska 50-61
Nederlands 62-73
Português 74-85
Compliances & Information 86-89
Table of Contents
SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 1

English
4
English
3
Front
1. Power (PWR) LED
When this blue LED is on, the router is powered up.
2. WAN LEDs
When the WAN LED has a solid blue light on, means there is an
active connection to the DSL/Cable modem. The PPPoE/DSL LED
beneath will show any activity of the WAN connection.
3. Wireless LAN (WLAN) LED
When this blue LED is on, wireless networking is enabled.
The LED will flash when data is sent or received over a wireless
connection.
4. LAN LEDs (LAN1, LAN2, LAN3 and LAN4)
There are two LEDs — one above the other — for each LAN
(Local Area Network) (see 7).
The top LED is green and the bottom is amber. These two LEDs
behave in exactly the same way as the WAN LEDs.
Hardware Description
System Requirements
To install and connect to the SMCWBR14T-G, you must have:
•An external Cable or DSL modem with an Ethernet port.
•An account with an ISP for Cable or DSL access.
•AComputer with a CD-ROM drive and working Ethernet port.
•Windows (98 or later), MacOS (9.x or later) or Linux.
•An up to date web browser:
• Internet Explorer 5.5 or later.
• Mozilla 1.7/Firefox 1.0 or later.
Note: A CD-ROM drive required to read the manual and if you want
to use the EZ 3-Click Installation Wizard application to
configure your Barricade™ Router. The installation process
can be completed manually through the web interface.
1
2
3
4
SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 3

English
5
English
6
5
Back
5. Power
Connect the supplied, 12V power adapter to this socket.
6. WAN Port
Use the supplied Ethernet cable to connect the WAN port to your cable
or DSL modem. The associated LED on the front panel will light up
when the connection is made.
7. LAN Ports (LAN1, LAN2, LAN3 and LAN4)
There are four Ethernet LAN ports for connection to PCs, network
printers or similar devices. Note the labelling; one pair of LAN LEDs on
the front panel is associated with one port on the rear panel.
If a device is not correctly connected, using a suitable Ethernet cable,
the associated LED will not turn on.
8. Reset
If, for any reason, you need to reset the unit to factory defaults
and cannot access the user interface (e.g. if you have changed
and forgotten the password), press the reset button for 10 seconds.
Note that you will lose all your configuration changes.
Ethernet Cables
One Ethernet cable, intended for your WAN connection, is bundled
with the router. You can use this as a point of reference for
purchasing other cables; the cable is constructed from unscreened,
“Cat 5” cable with RJ45 connecters at both ends. Cables of this
type can be purchased at most computer retailers.
The position of your Router is important to its wireless
performance. The Router should be located in a central position
relative to the wireless PCs that will connect to it. A suitable
location might be on a high shelf or a similar position that allows
good wireless coverage from the Router to the wireless PCs.
To meet the FCC wireless radiation exposure regulations, the Router
should be located in a position to maintain a minimum distance of
20cm (8 inches) from any personnel.
Connect all of the computers that you want to share on your
internet connection to your router. Connect your broadband
modem to the WAN port of the router.
During the initial setup, SMC recommend that the Router is
configured from a wired Ethernet PC as shown in the diagram.
Hardware Installation
WIRELESS
ROUTER
BROADBAND
MODEM
WIRELESS
LAPTOP
INTERNET
8
7
65
SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 5

If you want to mount this particular product onto the wall, please
use the holes at the bottom of this router as shown on the below
picture.
Follow the steps in this section after connecting your network as
described in the previous section.
Before beginning make sure you have all the details about your
internet connection from your ISP.
1. First, power-up your modem, then the router and finally power-
up the PC that you will use to configure the router.
2. Start your web browser and enter the address
http://192.168.2.1. If your PC is properly configured you will
see the login page of the router. If you cannot access the login
page then you must first reconfigure your PC to obtain an IP
address automatically; see the manual on the CD-ROM for more
information.
English
8
English
7
3. If you are using Windows, you now have the option of running
the EZ 3-Click installation wizard. If you are using another
operating system (e.g. MacOS or Linux) or require more help
than EZ 3-Click can provide, continue to step 4.
4. Type in the password (the default is smcadmin) and click on
Login. When you have successfully logged in, you will see the
Overview page which allows you to choose between the Setup
Wizard and Advanced Setup. Select Setup Wizard.
5. Click next to start the Setup Wizard. Here you will be able to
change the basic wireless settings such as SSID, Channel, Range
Extender and wireless operating mode. Click Next when finished
to move forward.
6. The next page of the wizard allows you to select your
broadband-connection type. Clicking on an option will
automatically move you to the next page. Read the text on this
screen carefully before making your choice.
7. The next page will ask you for technical information about your
internet connection. Your ISP should have provided you with
the information required to fill in this page. If you do not have
the required information then you may have picked the wrong
connection type during stage 6; you can click on the Back
button to try another connection type. When you have filled in
all the necessary details, click on the Finish button.
Important Note: If you are on a metered internet connection,
you should set your Maximum Idle Time to 1 minute.
8. That's It! You should be connected to the Internet.
Please register your product by pointing your Web browser to
http://www.smc.com and clicking through to the support pages.
If you are not connected to the Internet, please contact your ISP
to clarify your connection details.
Initial Configuration
SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 7

English
10
English
9
To setup Wireless networking you must select Home Network Settings
-> Wireless option in the Configuration menu.
1. To create a wireless network, the Router and wireless PCs must have
the same SSID and encryption settings. The default wireless
settings for the Router are shown below:
SSID - Router default is SMC
The SSID is the name given to your wireless LAN. Only PCs with the
same SSID as the Router can connect to the wireless LAN.
Wireless Encryption - Router default is off
To set up your wireless network, set the encryption to off in both
the Router and the wireless PC. Wireless encryption can be set
up later, after you have established a wireless network.
Wireless Channel - Router default is 6
The wireless channel is set in the Router and the default is
channel 6. The wireless PCs will automatically scan the channels to
detect which channel the Router is using.
If this is your only wireless network, then you can use the Router's
default settings. Now set your wireless PC to have the same SSID
and encryption settings as the Router. The wireless PCs must be set
to use infrastructure mode.
If your computer has both a wired and wireless connection
installed, then you must ensure that only one type is used at a
time, to connect to the LAN. To use the wireless connection,
unplug the wired Ethernet cable and reboot the PC.
Once you have setup the same SSID and Encryption in the Router and
wireless PC, open a browser and try to connect to www.smc.com. If
you can access the internet, then you have successfully set up your
wireless LAN.
Wireless Networking
The EZ 3-Click Application runs on Windows only and provides:
• An alternative approach to initial configuration.
• Access to the User Guide.
• Installation of Zone Alarm and Adobe Acrobat Reader.
To use EZ 3-Click, place the supplied CD in the CD-ROM drive of the
PC that is connected to the router. If your PC is configured to
auto-play CDs, the following dialog will appear on your screen.
If the dialog does not appear, you will have to start the
application manually. Do this by first opening Windows Explorer
then opening the folder associated with your CD-ROM drive. Once
you have opened the folder you will see the file SMCWBR14T-G.exe.
Run this file by double-clicking on it.
EZ Installation CD
SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 9

English
12
English
11
Installation Troubleshooting
• Check that the Power Adapter is switched on and is connected
to the Router. The green PWR LED on the Router should be on.
Use only the power adapter that was supplied with your Router.
• Check that the DSL or Cable modem, the Router and your PC are
all connected and displaying the correct LEDs.
•The DSL or Cable modem should connect to the WAN port of the
Router using an Ethernet cable. The WAN LED of the Router should
be on.
• The wired PC should connect to a LAN port of the Router using an
Ethernet cable. The corresponding LAN LED of the Router should be
on.
• Power up your equipment in the following order: First the DSL
or Cable modem, then the Router and then your PC. Leave about
1 minute between turning on each device.
• The PC should be setup to obtain an IP address automatically
from the Router's DHCP server. See the user manual on the CD
for details of how to setup your PC to obtain an IP address.
• Check that web proxy is disabled on your PC. Go to the Control
Panel and select Internet Options. Select the Connections tab
and click the LAN Settings button. Check that the Use Proxy
Server option is not ticked.
• Check you can access the Router's web interface. Open a browser
and enter http://192.168.2.1 to access the default IP address
of the Router.
WAN Connection Troubleshooting
• Check that you have selected the correct WAN connection option
and the ISP details are correct. If you do not have these details,
they can be obtained from your ISP.
• If you have any PPPoE client applications already installed on
your PC which were required when your PC was directly
connected to the DSL modem, they must be disabled.
Troubleshooting
2. SMC recommends that you enable wireless encryption to improve
the security of your wireless network. Note that if you change
the wireless settings (e.g. SSID or WEP) of your Router from a
wireless PC, then you may lose contact with your Router.
To re-establish the wireless connection, change the wireless
settings of your PC to be the same as the Router.
SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 11

Deutsch
14
English
13
Prüfen Sie bitte nach dem Auspacken des SMCWBR14T-G Routers
den Packungsinhalt, um sicherzugehen, dass folgende Teile
geliefert wurden:
•Ein Barricade™ SMCWBR14T-G 802.11g Wireless-Router.
•Ein Netzteil.
•Ein Ethernet-Kabel.
•Eine CD-ROM.
Informieren Sie bitte sofort Ihren Händler, wenn Teile fehlen,
falsch sind oder Beschädigungen aufweisen. Heben Sie, wenn
möglich, den Karton und die Originalverpackung auf.
Sie benötigen diese, wenn Sie das Produkt zurücksenden.
Bitte lassen Sie das Produkt registrieren und aktivieren Sie die
Produktgarantie auf der SMC-Website: www.smc.com.
Wireless Troubleshooting
•Check that the SSID is the same for the Router and the wireless PC.
•Check that the wireless encryption is the same on the Router and
the wireless PC. To help debug a problem, turn off encryption in both
the Router and wireless PC until you can establish a connection.
After a change in encryption, some PCs may have to be restarted.
•The wireless PCs must be set to Infrastructure mode to work with
a Router.
•If your computer has both a wired and wireless connection
installed, ensure that the wired Ethernet cable is unplugged.
•Check that the Router WLAN LED is on, to indicate that Wireless
networking is enabled. To enable wireless networking, go to the
Router Wireless page and enable Wireless Networking.
•If there are a number of wireless networks within range, then
you may experience poor wireless performance if the wireless
channels are too close together. Ideally, neighbouring wireless
networks should be at least 5 channels apart. The wireless
channel is controlled by and set in the Router.
•The Router has a feature called MAC Filter which controls which
wireless PCs have access to the wireless LAN. If this feature is
enabled, then ensure that the MAC address of your wireless PC
card is listed in the MAC Filter page.
Lieferumfang
SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 13

Deutsch
16
Deutsch
15
Vorderseite
1. Netz-LED [PWR]
Wenn diese blaue LED leuchtet, ist der Router eingeschaltet.
2. WAN-LEDs [WAN]
Wenn die WAN-LED blau leuchtet, besteht eine aktive
Verbindung zum DSL/Kabel-Modem. Die PPPoE/DSL-LED
[PPPoE/DSL] zeigt alle Aktivitäten der WAN-Verbindung.
3. Wireless-LAN-LED [WLAN]
Wenn diese blaue LED leuchtet, ist der kabellose
Netzwerkbetrieb aktiviert. Die LED blinkt, wenn Daten über
eine Wireless-Verbindung gesendet oder empfangen werden.
4. LAN-LEDs ([LAN1], [LAN2], [LAN3] und [LAN4])
Es gibt zwei — übereinander angeordnete — LEDs für jeden
LAN (Local Area Network)-Port (siehe 7).
Die obere LED ist grün und die untere ist gelb. Diese beiden
LEDs verhalten sich genauso wie die WAN-LEDs.
1
2
3
4
Systemanforderungen
Um den SMCWBR14T-G installieren und anschließen zu können,
müssen folgende Voraussetzungen erfüllt sein:
•Ein externes Kabel- oder DSL-Modem mit einem Ethernet-
Anschluss.
•Ein Konto bei einem Internet-Anbieter für Kabel-
oderDSL-Internet-Zugang.
•Ein Computer mit einem CD-ROM-Laufwerk und einem
funktionierenden Ethernet-Port.
•Windows (98 oder eine spätere Version), MacOS
(9.x oder eine spätere Version) oder Linux.
•Eine aktuelle Version eines Web-Browsers:
• Microsoft Internet Explorer 5.5 oder eine spätere Version.
• Mozilla 1.7/Firefox 1.0 oder eine spätere Version.
Hinweis: Ein CD-ROM-Laufwerk ist für den Zugriff auf die
Dokumentation und die Konfiguration des Barricade™-
Routers mit dem EZ3-Click-Installationsassistent
erforderlich. Die Installation kann manuell über
die Web-Schnittstelle ausgeführt werden.
Hardwarebeschreibung
SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 15

Deutsch
17
Deutsch
18
WIRELESS-ROUTER
BREITBANDMODEM
WIRELESS-
LAPTOP-
COMPUTER
INTERNET
ERSTER
COMPUTER
ZWEITER
COMPUTER
NETZTEIL
Die Position des Routers ist für die Leistung bei der kabellosen
Datenübertragung wichtig. Der Router sollte sich an einer
zentralen Position in Bezug auf die Wireless-PCs befinden, die mit
ihm verbunden werden. Beispielweise wäre ein hohes Regal oder
ein ähnlicher Ort in der Nähe der Wireless-PCs geeignet. Aus
Gründen des Strahlenschutzes sollte der Router mindestens 20 cm
von Personen entfernt sein. Schließen Sie alle Computer an, die
die Internet-Verbindung des Routers nutzen sollen. Verbinden Sie
Ihr Breitbandmodem mit dem WAN-Port des Routers. Es wird
empfohlen, den Router erstmalig von einem mit Kabel
angeschlossenen Ethernet-PC aus wie in der Abbildung gezeigt zu
konfigurieren.
Rückseite
5. Stromversorgung
An diese Buchse wird das mitgelieferte 12-V-Netzteil
angeschlossen.
6. WAN-Port
Über das im Lieferumfang enthaltene Ethernet-Kabel können Sie
den WAN-Port mit Ihrem Kabel- oder DSL-Modem verbinden.
Die entsprechende LED auf der Vorderseite leuchtet, wenn die
Verbindung hergestellt ist.
7. LAN-Ports ([LAN1], [LAN2], [LAN3] und [LAN4])
Es stehen vier Ethernet-LAN-Ports für die Verbindung zu PCs,
Netzwerkdruckern oder ähnlichen Geräten zur Verfügung. Beachten
Sie die Beschriftung. Jedes Paar von LAN-LEDs auf der Vorderseite
ist einem Port auf der Rückseite zugeordnet. Wenn ein Gerät nicht
ordnungsgemäß über ein geeignetes Ethernet-Kabel angeschlossen
ist, leuchtet die entsprechende LED nicht.
8. [Reset] (Zurücksetzen)
Wenn das Gerät aus irgendeinem Grund auf die Werkseinstellungen
zurückgesetzt werden muss und nicht auf die Benutzerschnittstelle
zugegriffen werden kann (z. B. wenn Sie das Kennwort geändert
und vergessen haben), drücken Sie
die Taste [Reset] (Zurücksetzen)
10 Sekunden lang. Alle Änderungen
an der Konfiguration gehen verloren.
Ethernet-Kabel
Mit dem Router wird ein Ethernet-Kabel für die WAN-Verbindung
geliefert. Dieses kann als Muster für andere Kabel verwendet
werden: nicht abgeschirmtes Kabel der Kategorie 5 mit RJ-45-
Anschlüssen an beiden Enden. Kabel dieses Typs sind im
Fachhandel erhältlich.
8
7
65
Hardwareinstallation
SMCWBR14T_G_QIG.qxd 10/06/05 15:53 Page 17