Smitson JM023-012A User manual

Ｂａｂｙ Ｂａｓｓｉｎｅｔ
ＪＭ０２３－０１２Ａ
ＵＳＥＲ ＭＡＮＵＡＬ
Smitson Jupiter Ltd
Gillingham, United Kingdom
www.smitsonjupiter.com
[email protected]

1
Ａｄｕｌｔ ａｓｓｅｍｂｌｙ ｒｅｑｕｉｒｅｄ．
Ｓｍａｌｌ ｐａｒｔｓ ｍａｙ ｐｒｅｓｅｎｔ ｃｈｏｋｉｎｇ ｈａｚａｒｄ ｐｒｉｏｒ ｔｏ ａｓｓｅｍｂｌｙ．
Ｅｎｃｌｏｓｅｄ ｐｌｅａｓｅ ｆｉｎｄ ｓｉｍｐｌｅ ｓｔｅｐ－ｂｙ－ｓｔｅｐ ｉｎｓｔｒｕｃｔｉｏｎｓ ｔｏ ｈｅｌｐ ｙｏｕ
ｑｕｉｃｋｌｙ ａｓｓｅｍｂｌｅ ｙｏｕｒ ｐｒｏｄｕｃｔｓ． Ｂｅｆｏｒｅ ｙｏｕ ｂｅｇｉｎ ｗｅ ｒｅｃｏｍｍｅｎｄ
ｔｈａｔ ｙｏｕ ｆｏｌｌｏｗｉｎｇ ｔｈｅ ｓｔｅｐｓ ｂｅｌｏｗ：
１． Ｐｌｅａｓｅ ｒｅａｄ ｔｈｅ ｉｎｓｔｒｕｃｔｉｏｎｓ ｔｈｏｒｏｕｇｈｌｙ．
２． Ｉｄｅｎｔｉｆｙ ａｌｌ ｐａｒｔｓ ａｎｄ ｈａｒｄｗａｒｅｓ．
３． Ｙｏｕ ｗｉｌｌ ｎｅｅｄ ｔｈｅ ｆｏｌｌｏｗｉｎｇ ｔｏｏｌｓ：
Ｐｈｉｌｉｐｓ ｈｅａｄ ｓｃｒｅｗ ｄｒｉｖｅｒ
Ｆｌａｔ ｈｅａｄ ｓｃｒｅｗ ｄｒｉｖｅｒ
Ｈａｍｍｅｒ
Ｄｏ Ｎｏｔ Ｕｓｅ Ｐｏｗｅｒ Ｄｒｉｌｌｓ ｏｒ Ｄｒｉｖｅｒｓ
Ｔｏ ｐｒｏｔｅｃｔ ｙｏｕｒ ｐａｒｔｓ ｄｕｒｉｎｇ ａｓｓｅｍｂｌｙ ｐｌｅａｓｅ ｐｌａｃｅ ｔｈｅｍ ｏｎ ａ ｓｏｆｔ
ｓｕｒｆａｃｅ．
Ｔｏ ｃｌｅａｎ ｓｕｒｆａｃｅ ｕｓｅ ｏｎｌｙ ｗａｔｅｒ ｏｎ ａ ｄａｍｐ ｃｌｏｔｈ． Ｄｏ ｎｏｔ ｕｓｅ
ｗｉｎｄｏｗ ｃｌｅａｎｅｒｓ ｏｒ ｃｌｅａｎｉｎｇ ａｂｒａｓｉｖｅｓ ａｓ ｉｔ ｗｉｌｌ ｓｃｒａｔｃｈ ｔｈｅ ｓｕｒｆａｃｅ
ａｎｄ ｃｏｕｌｄ ｄａｍａｇｅ ｔｈｅ ｐｒｏｔｅｃｔｉｖｅ ｃｏａｔｉｎｇ．

2
WARNING !
· FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR DEATH.
· READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP INSTRUCTIONS
FOR FUTURE USE.
· UPON COMPLETION OF ASSEMBLY, MAKE SURE ALL SCREWS,BOLTS AND
FASTENERS HAVE BEEN SECURELY TIGHTENED.
A FREQUENT AND PEDRIODICALLY CHECK SHOULD BE MADE TO CONFIRM ALL
THE SCREWS AND NUTS REMAIN TIGHT.
· NEVER USE THIS PRODUCT IF THERE ARE ANY LOOSE, MISSING FASTENERS,
LOOSE JOINTS,BROKEN PARTS, OR TORN MESH/FABRIC.CONTACT SUPPLIER FOR
REPLACEMENT PARTS AND INSTRUCTIONAL LITERATURE IF NEEDED.
· NEVER SUBSTITUTE PARTS, THE PRODUCT INCLUDING SIDE RAILS,MUST BE
FULLY ERECTED PRIOR TO USE.
· NEVER USE BED FOR INFANTS, THIS TODDLER BED IS NOT A SUBSITITUTE FOR A
CRIB,THE TODDLER BED IS USED FOR A CHILD BETWEEN THE AGE OF 15MONTHS
TO 5 YEARS WITH A MAXIMUM WEIGHT OF 50 POUNDS(22.7KG).
· NEVER USE PLASTIC SHIPPING BAGOR OTHER PLASTIC FILM AS A MATTRESS
COVERS NOT SOLD AND INTENDED FOR THAT PURPOSE,THEY CAN CAUSE
SUFFOCATION.
· CAUTION ENTRAPMENT HAZARD:TO AVOID DANGEROUS GAPS,ANY MATTRESS
USED IN THIS BED SHALL BE FULL SIZE CRIB MATTRESS AT LEAST 51-58IN
(1310MM) IN LENGTH, 27-1/4IN(690MM) IN WIDTH AND 4IN(100M) IN THICKNESS,OR
GREATER,BUT NOT EXCEED 5IN.
· NEVER USE A WATER MATTRESS WITH THIS TODDLER BED.
· WARNING STRANGULATION HAZARD:STRINGS CAN CAUSE STRANGULATION!
NEVER PLACE BED NEAR WINDOW WHERE CORDS FROM BLINDS OR DRAPES
MAY STRANGLE A CHILD.NEVER SUSPEND STRINGS OVER BED.
NEVER PLACE ITEMS WITH A STRING CORD,OR RIBBON,SUCH AS HOOD STRINGS,
PACIFIER CORDS AOUND A CHILS’S NECK.THESES ITEMS MAY CATCH ON BED
PARTS.
· WARNING: INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT.
OPENINGS IN AND BETWEEN BED PARTS CAN ENTRAP HEAD AND NECK OF A
SMALL CHILD. NEVER USE BED WITH CHILDREN UNDER 15MONTHS.ALWAYS
FOLLOW THE ASSEMBLY INSTRUCTIONS.
· TO REDUCE THE RISK OF SIDS,PEDIASTRICIANS RECOMMED HEALTHY INFANTS
BE PLACED ON THEIRE BACK TO SLEEP,OR ADVISED BY YOUR PHYSICIAN.
· DO NOT USE BED IF THE SPACE BETWEEN BED AND SOLID OBJECTS IS LESS
THAN 12IN(31CM), A CHILD COULD SLID INTO THE SPACE AND SUFFOCATE.
· IF REFINISHING,USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN’S PRODUCTS.
TO WASH,CLEAN WITH MILD SOAP AND DAMP CLOTH.
TO STORE,PLEASE KEEP IN A COOL PLACE.
MADE IN CHINA

COMPONENT PARTS
3
HARDWARE AND TOOL DIAGRAM
Do Not Use Power
Drills or Drivers
PHILLIPS--HEAD SCREWDRIVER
REQUIRED FOR ASSEMBLY
----NOT INCLUDE
CLÉ À MOLETTE ET TOURNEVIS
À TËTE PLATE REQUIS POUR
L'ASSEMBLAGE (NON COMPRIS)
a:
2-1/8”
Allen head bolt (8 pcs) d: lewod dooW ”2/1-1
(2 pcs)
b:
Barrel nuts (10 pcs)
h: Latc h 1 (2 pcs)
m : o: Nut (4 pcs) p: Bolt (4 pcs) P lastic b )scp 4(
k
co
l
i: Lat ch 2
(2 pcs)
k: 3/4”screw (8 pcs)
j: 5/8” screw
(2 pcs)
n: 5/8” screw
(4 pcs)
c: hcnerw nellA ”2
(1 pc)
f: Castors
(2 pcs)
g:
Castors
(2 pcs)
e: Lock nuts (2 pcs)
A: Left head board (1PC) B: Right head board (1PC) C: Rail (2Pcs)
E: Mattress board (1PC) F: Mattress (1PC)

4
STEP# 1
STEP# 2
Note: don't tighten the bolts before finishing the last step.
a
c
a
b
b
a
A
B
C
B
A
nn
j
i
h
k
km
Connect rail(C) to the headboard (A&B)
by screws(a)and nuts(b).DO NOT fully
ghten the bolts.
Assemble latch(h&i)to the headbaord(A&B)
by using5/8'' screw(j&n).Then asemble
plasc block(m)horizontal to the
headboard(A&B)by using 3/4'' screw(kk).
Tighten screws usging a phillips-head
screwdriver.Make sure that the latch on
the boom of each headbaord(A&B)
are locked.

5
STEP# 4
STEP# 3
A
e
B
E
A
B
C
b
b
b
b
Aach the maress board(D)to the
heardboard(A&B)by lock nuts(e).
Connect rail(C) to the headboard (A&B)by screws
（a）and nuts(b).THEN FULLY ghten the bolts.

6
STEP# 5
STEP# 6
g
o
p
f
f
f
WRENCH AND
PHILLIPS--HEAD SCREWDRIVER
REQUIRED FOR ASSEMBLY
----NOT INCLUDE
Select the desire level,and use both hand to
li up the maress base ,then adjust the level
to your require height of the 2 level.Slide in the
bolt underneath the maress board (D) to keep
the maress support fixed.
Assemble castors(d&f)to the leg
booms on the leg on headboard(A&B)
by using bolt(p)and nut(o).2 castors(d)with
brake are in the front .THEN add the maress .

7
①
②
①②
Follow bellow to fold the crib:
1.take out the mattress (F)
2.take out the mattress board (E)
3.unlock the latch on the headboard
4.fold the crib

8
LIMITED WARRANTY
� warrants its product to be free from defects in material and
workmanship and agrees to remedy any such defect.
� This warranty covers 30 days from the date of original purchase.
� This warranty is valid only upon presentation of proof of purchase.
This is solely limited to the repair or replacement of defective furniture
components and no assembly labor is included.
� This warranty does not apply to any product which has been improperly
assembled, subjected to misuse or abuse or which has been altered or
repaired in any way.
� This warranty gives you specific legal rights and you may also have other
rights which vary from State to State.
WARNING: Should this product become damaged, and/or components
are broken or missing, DO NOT USE
JM023-012A