Delta Children Classic User manual

March 24, 2014, 24435, R1
A
Conforms to
ASTM F1821
Safety Standards
When contacting Delta Consumer Care please reference the above information. Before
contacting Delta Consumer Care please ensure that the information above matches the
information found on the label on the Headboard bottom rail, please reference the information
found on the product when contacting Delta Consumer Care.
Style #:
Lot:
Date:
___________
___________
___________
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
REV
THIS PRODUCT IS NOT INTENDED FOR
INSTITUTIONAL OR COMMERCIAL USE.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of
reach of children until assembly is complete.
To register your product for important safety alerts and updates to your product please visit
www.DeltaChildren.com and click on Product Registration.
©2014 DELTA ENTERPRISE CORP.

2
TODDLER BED
WARNING
INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT.
Openings in and between bed parts can entrap head and neck of a small child.
NEVER use bed with children younger than 15 months.
ALWAYS follow assembly instructions.
The maximum user weight is 50lbs (22.7kg)
WARNING
STRANGULATION HAZARD
NEVER place bed near windows where cords from blinds or drapes may strangle a child.
NEVER suspend strings over a bed.
NEVER place items with a string, cord, or ribbon, such as hood strings or pacifier cords,
around a child's neck. These items may catch on bed parts.
CAUTION
ENTRAPMENT HAZARD
To avoid dangerous gaps, any mattress used in this bed shall be a full-size crib mattress
at least 51 5⁄8 in. (1310 mm) in length, 27 1⁄4 in. (690 mm) in width., and a max thickness
of 5 3/4 in. (146 mm).
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact Delta Children's Products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
NOTES ON USE:
Keep children and others safe by following these simple rules:
- Do not allow any child to play on furniture
- Do not allow climbing on any piece of furniture.
- Do not allow hanging from any piece of furniture.
- Always monitor your child’s activity when in the nursery.

PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
A. End Top Rail x 2
J. Headboard Bottom Panelx 1
3
K. Left Back Side Rail x 1
Part # 24423
B. Headboard Middle Rail x 1
Part # 24493
Part # 24432
Part # 24495
F. Left Footboard Post x 1
G. Right Footboard Post x 1
Part # 24428
Part # 24429
L. Right Back Side Rail x 1
Part # 24431
M. Front Side Rail x 2
Part # 24433
N. Cross Slat x 10
Part # 21646
P. Center Cross Slat x 1
Part # 21647
S. Guard Rail x 2
Part # 24425
R. Center Leg x 2
Part # 24430
D. Left Headboard Post x 1
E. Right Headboard Post x 1
Part # 24426
Part # 24427
C. End Bottom Rail x 2
Part # 24424
H. End Top Panel x 2
Part # 24494

PARTS:
4
(not supplied)
Flat Head Screwdriver
W. M6x13 mm Barrel Nut x 24
M4 Allen Wrench Supplied
T. M6 x 85 mm Bolt x 8
U. M6 x 60 mm Bolt x 16
No drills necessary. Do not
use power screwdriver.
Part # 5474
Part # 5469
Part # 5483
Part # 1177
V. M6 x 45 mm Bolt x 2
Part # 5466
X. Φ8x40 mm Wood Dowel x 4
Part # 5672
Y. Mending Plate x 2
Part # 5673
HARDWARE KIT PART #24434-986 FOR COLOR 100 OR #24434-988 FOR COLOR
607. SEE FRONT COVER.

5
Step 1
M4 Allen Wrench Supplied
Attach (1) End Top Rail (Part A) and (1) End Bottom Rail (Part C) to (1) Left Headboard Post (Part D)
using (2) M6x85mm Bolts (Part T) and (2) M6x13mm Barrel Nuts (Part W). Tighten with the M4 Allen
Wrench. Use the Flat Head Screwdriver to hold the Barrel Nut in the proper alignment.
W. M6x13 mm Barrel Nut x 2
T
Parts and tools required to complete step.
T. M6 x 85 mm Bolt x 2
D. Left Headboard Post x 1
A. End Top Rail x 1
C. End Bottom Rail x 1
A
C
C
W
D
D
T
W
BACK!
W
T
BACK!

6
Step 2
From Step 1
Parts and tools required to complete step.
J. Headboard Bottom Panelx 1
B. Headboard Middle Rail x 1
H. End Top Panel x 1
J
B
H
Insert (1) Headboard Middle Rail (Part B) as shown.
Slide End Top Panel (Part H) into End Top Rail (Part A) and Headboard Middle Rail (Part B) Grooves
as shown.
Slide Headboard Bottom Panel (Part J) into Headboard Middle Rail (Part B) and End Bottom Rail
(Part C) Grooves as shown.

7
Step 3
Attach (1) Right Headboard Post (Part E) to the assembly from step 2 using (2) M6x85mm Bolts (Part T)
and (2) M6x13mm Barrel Nuts (Part W). Tighten with the M4 Allen Wrench. Use the Flat Head
Screwdriver to hold the Barrel Nut in the proper alignment.
M4 Allen Wrench Supplied
W. M6x13 mm Barrel Nut x 2
From Step 2
Parts and tools required to complete step.
T. M6 x 85 mm Bolt x 2
E. Right Headboard Post x 1
T
T
W
W
BACK!

8
Step 4
M4 Allen Wrench Supplied
Attach (1) End Top Rail (Part A) and (1) End Bottom Rail (Part C) to (1) Left Footboard Post (Part F)
using (2) M6x85mm Bolts (Part T) and (2) M6x13mm Barrel Nuts (Part W). Tighten with the M4 Allen
Wrench. Use the Flat Head Screwdriver to hold the Barrel Nut in the proper alignment.
W. M6x13 mm Barrel Nut x 2
T
Parts and tools required to complete step.
T. M6 x 85 mm Bolt x 2
A. End Top Rail x 1
C. End Bottom Rail x 1
A
C
W
F
T
W
F. Left Footboard Post x 1
BACK!
FRONT!
F
C
A

9
Step 5
From Step 4
Parts and tools required to complete step.
H. End Top Panel x 1
H
Slide End Top Panel (Part H) into End Top Rail (Part A) and End Bottom Rail (Part C) Grooves as
shown.
BACK!

10
Step 6
Attach (1) Right Footboard Post (Part G) to the assembly from step 5 using (2) M6x85mm Bolts (Part T)
and (2) M6x13mm Barrel Nuts (Part W). Tighten with the M4 Allen Wrench. Use the Flat Head
Screwdriver to hold the Barrel Nut in the proper alignment.
M4 Allen Wrench Supplied
W. M6x13 mm Barrel Nut x 2
From Step 5
Parts and tools required to complete step.
T. M6 x 85 mm Bolt x 2
TT
W
W
BACK!
G. Right Footboard Post x 1

11
Step 7
Attach (1) Right Back Side Rail (Part L) to the assembly from step 3 using (2) M6x60mm Bolts (Part U)
and (2) M6x13mm Barrel Nuts (Part W). Tighten with the M4 Allen Wrench. Use the Flat Head
Screwdriver to hold the Barrel Nut in the proper alignment.
M4 Allen Wrench Supplied
W. M6x13 mm Barrel Nut x 2
From Step 3
Parts and tools required to complete step.
U. M6 x 60 mm Bolt x 2
L. Right Back Side Rail x 1
L
E
W
U

12
Step 8
From Step 7
N. Cross Slat x 5
Insert (5) Cross Slats (Part N) as shown.
L
N
N
Parts and tools required to complete step.

13
Step 9
Attach (1) Left Back Side Rail (Part K) to the assembly from step 8 using (2) M6x60mm Bolts (Part U)
and (2) M6x13mm Barrel Nuts (Part W). Tighten with the M4 Allen Wrench. Use the Flat Head
Screwdriver to hold the Barrel Nut in the proper alignment.
M4 Allen Wrench Supplied
From Step 8
K. Left Back Side Rail x 1
K
N
U
W
Parts and tools required to complete step.
W. M6x13 mm Barrel Nut x 2
U. M6 x 60 mm Bolt x 2

14
Step 10
Attach (1) Front Side Rail (Part M) to the assembly from step 6 using (2) M6x60mm Bolts (Part U)
and (2) M6x13mm Barrel Nuts (Part W). Tighten with the M4 Allen Wrench. Use the Flat Head
Screwdriver to hold the Barrel Nut in the proper alignment.
M4 Allen Wrench Supplied
From Step 6
M. Front Side Rail x 1
U
M
Parts and tools required to complete step.
W. M6x13 mm Barrel Nut x 2
U. M6 x 60 mm Bolt x 2
W

15
Step 11
From Step 10
N. Cross Slat x 5
Insert (5) Cross Slats (Part N) as shown.
M
N
N
Parts and tools required to complete step.

16
Step 12
Attach (1) Front Side Rail (Part M) to the assembly from step 11 using (2) M6x60mm Bolts (Part U)
and (2) M6x13mm Barrel Nuts (Part W). Tighten with the M4 Allen Wrench. Use the Flat Head
Screwdriver to hold the Barrel Nut in the proper alignment.
M4 Allen Wrench Supplied
From Step 11
M
Parts and tools required to complete step.
M. Front Side Rail x 1
W. M6x13 mm Barrel Nut x 2
U. M6 x 60 mm Bolt x 2
U
W

17
Step 13
Insert (1) Center Cross Slat (Part P) in the grooves on the end of the Front Side Rails (Part M).
Attach the assembly from step 12 to the assembly from step 9 using (4) Φ8x40 mm Wood Dowels
(Part X).
From Step 12
From Step 9
P. Center Cross Slat x 1
X. Φ8x40 mm Wood Dowel x 4
L
K
M
X
P
M
X
Parts and tools required to complete step.

18
Step 14
M4 Allen Wrench Supplied
W. M6x13 mm Barrel Nut x 4
From Step 13
R. Center Leg x 2
Y. Mending Plate x 2
R
U
M
M
L
K
Y
R
U
THE ROUND EDGES ON THE
PLATE (PART X) MUST FACE
UP.
L
M
RU
W
PY
W
Parts and tools required to complete step.
U. M6 x 60 mm Bolt x 4
PW
Y
Attach (2) Center Legs (Part R) to the assembly from step 13 using (2) Mending Plates (Part Y),
(4) M6x60mm Bolts (Part U) and (4) M6x13mm Barrel Nuts (Part W). Tighten with the M4 Allen
Wrench. Use the Flat Head Screwdriver to hold the Barrel Nut in the proper alignment.

19
Step 15
Attach (2) Guardrails (Part S) to the assembly from step 14 using (2) M6x45mm Bolts (Part V),
(4) M6x60mm Bolts (Part U) and (4) M6x13mm Barrel Nuts (Part W). Tighten with the M4 Allen Wrench.
Use the Flat Head Screwdriver to hold the Barrel Nut in the proper alignment.
M4 Allen Wrench Supplied
W. M6x13 mm Barrel Nut x 4
From Step 14
S. Guard Rail x 2 V. M6 x 45 mm Bolt x 2
Parts and tools required to complete step.
U. M6 x 60 mm Bolt x 4
V
V
W
U
U
S
S
W
U
U

Warranty: This Delta product is warranted to be free from defects for a period
of 90 days from the date of purchase under normal use. This warranty extends
only to the original retail purchaser and is valid only when supplied with proof of
purchase, or if received as a gift, when the registration is on file with Delta.
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
Please do not return this item to the store before contacting
us about missing parts or with any questions.
To register your product for important safety alerts and updates to
your product please visit www.DeltaChildren.com
To report a problem, please log on to www.DeltaChildren.com and
click the Consumer Care Tab, or contact us by phone at
[phone].
In the event that you need to contact our customer service
department please have the Style Number and Lot Number available.
Use the space below to make note of those numbers. They can be
found on the label on the Headboard bottom rail.
Lot No. : _______________________
Pack Date:_____________________
Date of Purchase: _____________ (you should also keep your receipt)
COLOR FTY
REV
STYLE No: 7148 A