Snapper 4544 Setup guide

Attachment
Illustrated
Parts List
Rev. 10/2007
500 N. Spring Street / PO Box 997
Port Washington, WI 53074-0997 USA
www.simplicitymfg.com
MANUFACTURING, INC.
© Copyright Simplicity Manufacturing, Inc. All Rights Reserved. Printed In USA.2007 TP 400-4544-01-AT-SMA
Mf
g
. No. Descri
p
tion
Attachment
1694924 Turbo Collector Regent, 44" & 50" Mower
1734823
Part No.:

Table Of Content
s
Torque Specification Chart ..................................................................... Inside Back Cover
PRODUCT COMPONENTS PAGES
Turbo, Blower ....................................................................................................................................................... 4
Turbo, Mounting Kit .............................................................................................................................................. 6

Turbo, Blower
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
987376
The above parts group applies to the following Mfg. Nos.:
4
2007Copyright © by Briggs and Stratton Corporation
Briggs and Stratton Yard Power Products Group
Milwaukee, WI, USA. All rights reserved
1694924 - Turbo Collector Re
g
en
TP 400-4544-01-AT-SMA

PART NO. DESCRIPTIONREF NO QTY.
Turbo, Blower
Footnotes
HOUSING FAN ASSEMBLY1 1724441SM 1 BOLT, Carriage, 1/4 - 20 x 3/42 1931317SM 4 NUT, Hex Flange Whiz Lock, 1/4 - 203 1930641SM 10 BOLT, Carriage, 5/16 -18 x 3/44 1931333SM 7 RETAINER, Bearing5 1665982ASM 4 BEARING6 2108202SM 2 PUSH NUT, 5/167 1933988SM 6 NUT, Hex Flange Whiz Lock8 1927557SM 6 FAN ASSEMBLY, Five Paddle9 1706631ASM 1 KEY, Woodruff10 2860403SM 1 PLATE ASSEMBLY11 1706465ASM 1 BOLT, Carriage, 3/8 -1612 1931355SM 1 WASHER, Flat13 1924361SM 1 LEVER ASSEMBLY, Turbo14 1706284ASM 1 FITTING, Lube15 2821133SM 1 BUSHING16 1676148SM 2 WASHER, Flat17 1924940SM 3 NUT, Hex Center Lock Jam, 3/8 - 1618 1960251SM 2 BELT, Stop19 1678435SM 1 WASHER, Flat20 1924874SM 1 LOCKWASHER, 5/1621 1917356SM 1 NUT, Hex, 5/16 - 1822 1917372SM 1 PULLEY ASSEMBLY IDLER23 1706634SM 1 SETSCREW, Torx24 1960619SM 2 CAPSCREW, Hex Head, 3/8 - 16 x 1-1/425 1920415SM 1 PULLEY ASSEMBLY IDLER26 2154534SM 1 WASHER, Flat27 1933263SM 1 SCREW, Washer Head Taptite, 1/4 - 20 x 1/228 1925003SM 1 CAPSCREW, Hex Head, 1/4 - 20 x 7/829 1924009SM 2 ANCHOR, Spring30 1668500SM 1 DECAL, Danger (Included with Ref. No. 1)31 1700259SM 1 SPRING, Tension32 1716853SM 1 PLATE, Cover33 1705267SM 1 SCREW, Hex Washer Head, 1/4 x 3/434 1960728SM 2 SPACER35 1676833SM 1 DECAL, Patent36 1713057SM 1 CAPSCREW, 1/4 - 20 x 5/852 1921959SM 4
The above parts group applies to the following Mfg. Nos.:
5
2007Copyright © by Briggs and Stratton Corporation
Briggs and Stratton Yard Power Products Group
Milwaukee, WI, USA. All rights reserved
1694924 - Turbo Collector Re
g
en
TP 400-4544-01-AT-SMA

Turbo, Mounting Kit
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
987368
The above parts group applies to the following Mfg. Nos.:
6
2007Copyright © by Briggs and Stratton Corporation
Briggs and Stratton Yard Power Products Group
Milwaukee, WI, USA. All rights reserved
1694924 - Turbo Collector Re
g
en
TP 400-4544-01-AT-SMA

PART NO. DESCRIPTIONREF NO QTY.
Turbo, Mounting Kit
Footnotes
PIVOT BRACKET ASSEMBLY1 1722546ASM 1 NUT, Hex Whiz Lock Flange, 5/16 - 182 1931277SM 7 SUPPORT, Belt Cover3 1718304ASM 1 COVER, Belt, 44"4 1724374ASM 1 COVER, Belt, 50"4 1724376ASM 1 WASHER, Flat, 5/165 1919326SM 4 CAPSCREW, Hex, 5/16 - 18 x 7/86 1923325SM 7 BOLT, Carriage, 5/16 - 18 x 3/47 1931333SM 1 BOLT, Carriage, 1/4 - 20 x 3/48 1931317SM 2 DECAL, Warning9 1717291SM 2 COVER, Mower10 1732591ASM 1 NUT, Keps Conical, 1/4 - 2011 1960685SM 2 BRACKET, Baffle12 1732592ASM 1 CAPSCREW, Hex, 5/16 - 18 x 2-1/213 1960318SM 1 BAFFLE, Turbo14 1732619ASM 1 SPRING, Latch15 1705064SM 1 WASHER, 5/1616 1919381SM 1 NUT, Keps Lock, 5/16 - 1817 1960636SM 1 ROD, Deflector19 1718295ASM 1 NUT, ESNA Lock, 10 - 2420 1933896SM 13 SCREW, Truss Phillips, 10 - 24 x 3/421 1960404SM 13 CAPSCREW, Hex, 3/8 - 16 x 222 1923701SM 1 WASHER, Flat, 3/823 1924940SM 3 PULLEY, Idler, 2-3/424 1714817SM 1 WASHER, Flat25 1910531SM 2 BRACKET, "L"26 1724373ASM 1 BRACKET, "Z"27 1704768ASM 1 NUT, Whiz Lock Small, 3/8 - 1628 1931211SM 1 CAPSCREW, Hex, 5/16 - 18 x 1-1/229 1921221SM 1 LOCKWASHER, 5/1630 1917356SM 1 STOP, Belt31 2172845SM 1 SPACER32 1710703SM 1 NUT, Short Sleeve33 1733078SM 1 WASHER, Flat, 7/834 1603592SM 1 PULLEY, 4.335 1709941SM 1 HUB, Double, 5/836 1713623SM 1 NUT, Push37 1960520SM 1 ROLLER38 1713540SM 1 TUBE ASSEMBLY, Lower39 1719719SM 1 V-BELT, 39.62 (50" Mower Decks)40 1732801SM 1 V-BELT, 37.9 (44" Mower Decks)41 1732945SM 1 SEAL, Flange42 1732735ASM 1 DECAL, Patent43 1713057SM 1 SEAL, Cover45 1733741SM 1
The above parts group applies to the following Mfg. Nos.:
7
2007Copyright © by Briggs and Stratton Corporation
Briggs and Stratton Yard Power Products Group
Milwaukee, WI, USA. All rights reserved
1694924 - Turbo Collector Re
g
en
TP 400-4544-01-AT-SMA

Turbo, Mounting Kit
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
987368
The above parts group applies to the following Mfg. Nos.:
8
2007Copyright © by Briggs and Stratton Corporation
Briggs and Stratton Yard Power Products Group
Milwaukee, WI, USA. All rights reserved
1694924 - Turbo Collector Re
g
en
TP 400-4544-01-AT-SMA

PART NO. DESCRIPTIONREF NO QTY.
Turbo, Mounting Kit
Footnotes
PIN, Klik47 1960074SM 1 TUBE, Upper48 1732800SM 1 NUT, ESNA, 5/16 - 1849 1919438SM 2 WINGNUT51 071294MA 1 PLATE, Deflector59 1733580ASM 1 SEAL, Rubber60 1717496SM 1 SEAL, Rubber61 1733579SM 1 SPRING, Compression (For Use On Snapper Models)62 1729277SM 1 COLLAR, Locking (For Use On Snapper Models)63 1719777SM 1 SCREW, Set, 5/16 - 19 (For Use On Snapper Models)64 1928721SM 1 WASHER, Spring Cup65 1709256SM 1 HARDWARE BAG-- 1660934SM 1 INSTALLATION INSTRUCTIONS-- 1732839 1
The above parts group applies to the following Mfg. Nos.:
9
2007Copyright © by Briggs and Stratton Corporation
Briggs and Stratton Yard Power Products Group
Milwaukee, WI, USA. All rights reserved
1694924 - Turbo Collector Re
g
en
TP 400-4544-01-AT-SMA

Torque Specification Chart
FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)
Hardware
Grade
SAE Grade 2 SAE Grade 5 SAE Grade 8
Size Of in/lbs in/lbs in/lbs
Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm.
8-32 19 2.1 30 3.4 41 4.6
8-36
20 2.3 31 3.5 43 4.9
10-24
27 3.1 43 4.9 60 6.8
10-32
31 3.5 49 5.5 68 7.7
1/4-20
66 7.6 810.9 12 16.3
1/4-28
76 8.6 10 13.6 14 19.0
5/16-18 11 15.0 17 23.1 25 34.0
5/16-24 12 16.3 19 25.8 27 34.0
3/8-16 20 27.2 30 40.8 45 61.2
3/8-24 23 31.3 35 47.6 50 68.0
7/16-14 30 40.8 50 68.0 70 95.2
7/16-20 35 47.6 55 74.8 80 108.8
1/2-13 50 68.0 75 102.0 110 149.6
1/2-20 55 74.8 90 122.4 120 163.2
9/16-12 65 88.4 110 149.6 150 204.0
9/16-18 75 102.0 120 163.2 170 231.2
5/8-11 90 122.4 150 204.0 220 299.2
5/8-18 100 136 180 244.8 240 326.4
3/4-10 160 217.6 260 353.6 386 525.0
3/4-16 180 244.8 300 408.0 420 571.2
7/8-9 140 190.4 400 544.0 600 816.0
7/8-14 155 210.8 440 598.4 660 897.6
1-8 220 299.2 580 788.8 900 1,244.0
1-12 240 326.4 640 870.4 1,000 1,360.0
Hex Head Capscrew
Hex Nut
Lockwasher
Washer
Carriage Bolt
NOTES
1. These torque values are to be used for all hardware
excluding:locknuts, self-tapping screws, thread forming
screws, sheet metal screws and socket head setscrews.
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5
torques.
b. for flange whizlock nuts and screws - use 135% of
grade 5 torques.
3. Unless otherwise noted on assembly drawings, all torque
values must meet this specification.
Hardware Identification & Torque Specifications
Common HardwareTypes
Screw, 1/2 x 2
Body
Diameter
Body
Length
Inside
Diameter
Nut, 1/2”
No
Marks
3/8”Bolt or Nut
Wrench—9/16”
3/8
5/16”Bolt or Nut
Wrench—1/2”
5/16
1/4”Bolt or Nut
Wrench—7/16”
1/4
1/2”Bolt or Nut
Wrench—3/4”
1/2
DIA.
7/16
DIA.
7/16”Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
Wrench & Fastener Size Guide
Standard Hardware Sizing
When a washer or nut is identified as 1/2”, this is the
Nominal size , meaning the inside diameter is 1/2 inch; if a
second number is present it represent the
threads per inch
When bolt or capscrew is identified as 1/2 - 16 x 2”, this
means the
Nominal size , or body diameter is 1/2 inch; the
second number represents the
threads per inch (16 in this
example, and the final number is the
body length of the
bolt or screw (in this example 2 inches long).
The guides and ruler furnished below are designed to
help you select the appropriate hardware and tools.
0
1/4 3/4
1/2
1
1/4 3/4
1/2
2
1/4 3/4
1/2
3
1/4 3/4
1/2
4