Snell & Wilcox Supervisor LX User manual

FGAX3249400MANAA 100701 Version 1 Issue 2 0.1
Operation &
Installation
Manual
© July 2001
Snell & Wilcox Ltd, Durford Mill, Petersfield, Hampshire, GU31 5AZ, United Kingdom.
Tel: [phone]. Fax: [phone].
Supervisor LX
LED Display Processor

SuperVisor LX SECTION 0
FGAX3249400MANAA 100701 Version 1 Issue 2 0.2
Explanation of Safety Symbols
This symbol refers the user to important information contained in the accompanying literature.
Refer to users manual.
This symbol indicates that hazardous voltages are present inside. No user serviceable parts
inside. This unit should only be serviced by trained personnel.
Safety Warnings
No user serviceable parts inside. Servicing instructions where given are for use
by qualified personnel only. To reduce risk of electric shock do not perform any
servicing other than that contained in the operating instructions unless you are
qualified to do so. Refer all servicing to qualified personnel.
WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES MUST NOT BE PLACED ON THIS
EQUIPMENT.
•Always ensure that the unit is properly earthed and power connections correctly made.
•This equipment must be supplied from a power system providing a PROTECTIVE EARTH
connection and having a neutral connection which can be reliably identified.
•The power outlet supplying power to the unit should be close to the unit and easily accessible
Power cable supplied
The equipment is shipped with a power cable with a standard IEC moulded free socket on one end and a
standard IEC moulded plug on the other. If you are required to remove the moulded mains supply plug,
dispose of the plug immediately in a safe manner. The colour code for the lead is as follows:
GREEN/YELLOW lead connected to E (Protective Earth Conductor)
BLUE lead connected to N (Neutral Conductor)
BROWN lead connected to L (Live Conductor)
The terminals of the IEC mains supply lead are identified as shown above.

SuperVisor LX SECTION 0
FGAX3249400MANAA 100701 Version 1 Issue 2 0.3
Safety Standard
This unit has been tested to BS EN60950:2000
Specification for safety of technology equipment, including electrical business equipment.
EMC Standards
This unit conforms to the following standards:
BS EN 55103-1 : 1997
Electromagnetic Compatibility, Product family standard for audio, video, audio-visual and entertainment lighting
control apparatus for professional use. Part 1. Emission
BS EN 55103-2 : 1997
Electromagnetic Compatibility, Product family standard for audio, video, audio-visual and entertainment lighting
control apparatus for professional use. Part 2. Immunity.
Federal Communications Commission Rules Part 15, Class A :1998
EMC Environment
The product(s) described in this manual conform to the EMC requirements for, and are intended for use in,
the commercial and light industrial environment (including, for example, theatres) E2
EMC Performance Information
Inrush current: Supervisor LX Display Processor ...................................48.76 A at Ø°
Inrush current: Supervisor LX Shoebox Controller ................................8.2 A at Ø°

SuperVisor LX SECTION 0
FGAX3249400MANAA 100701 Version 1 Issue 2 0.4
EMC Performance of Cables and Connectors
Snell & Wilcox products are designed to meet or exceed the requirements of the appropriate European EMC
standards. In order to achieve this performance in real installations it is essential to use cables and connectors
with good EMC characteristics.
All signal connections (including remote control connections) shall be made with screened cables terminated in
connectors having a metal shell. The cable screen shall have a large-area contact with the metal shell.
COAXIAL CABLES
Coaxial cables connections (particularly serial digital video connections) shall be made with high-quality
double-screened coaxial cables such as Belden 8281 or BBC type PSF1/2M.
D-TYPE CONNECTORS
D-type connectors shall have metal shells making good RF contact with the cable screen. Connectors having
"dimples" which improve the contact between the plug and socket shells are recommended.
RS422 CABLE
This should feature 5 twisted pairs, braided and foil screened with metal shell connectors and should be EMC
approved (see above) or conform to equivalent U.S. standards.
VGA CABLE
This should feature 5 individual coaxial cables (internal) for the video signals and at least 3 un-screened
cables. This group of cables must be screened overall and where possible a ferrite tube type 43 material (such
as Fair-Rite™ type 2643665702) should be fitted to the cable adjacent to the connector.

SuperVisor LX SECTION 0
FGAX3249400MANAA 100701 Version 1 Issue 2 0.5
Manufacturers Notices
COPYRIGHT
Copyright protection claimed includes all forms and matters of copyrightable material and information now
allowed by statutory or judicial law or hereinafter granted, including without limitation, material generated from
the software programs which are displayed on the screen such as icons, screen display looks etc.
Information in this manual and software are subject to change without notice and does not represent a
commitment on the part of Snell & Wilcox Ltd. The software described in this manual is furnished under a
license agreement and may not be reproduced or copied in any manner without prior agreement with Snell &
Wilcox Ltd. or their authorized agents.
Reproduction or disassembly of embedded computer programs or algorithms prohibited.
Copyrighted names: Microsoft Windows™
No part of this publication may be transmitted or reproduced in any form or by any means, electronic or
mechanical, including photocopy, recording or any information storage and retrieval system, without
permission being granted, in writing, by the publishers or their authorized agents.
Packing List
The unit is supplied in a dedicated packing carton provided by the manufacturer and should not be accepted if
delivered in inferior or unauthorized materials. Carefully unpack the carton and check for any shipping damage
or shortages. Any shortages or damage should be reported to the supplier immediately.
Enclosures:
Mainframe Shoebox Controller
•SuperVisor LX Mainframe Unit
•Power cable
•Fuses 2.5 A (T) 2 pieces
•SuperVisor LX Operation & Installation Manual
•Linking Cables BNC to BNC Red, Green, Blue
•75 Ohm through terminator
•Y-C Interface cable 4 pin Mini-DIN to BNC’s
•SVGA Interface cable 15 pin D type to BNC’s
•SuperVisor LX Shoebox Controller
•Power cable
•Fuses 1 A (T) 2 pieces
•SuperVisor LX Shoebox Controller Manual
•Cable BNC to BNC 1 m
•75 Ohm through terminator
Additional Y-C Interface cables are available in the
UK from:
COMPOSITE VIDEO LTD
Unit 3
Four Seasons Crescent
Kimpton Road
SUTTON
Surrey Tel: [phone]
Note that similar products may be available from
other companies.
Additional SVGA Interface cables are available in the
UK from:
VIDEK
Kingsbury Trading Estate
Kingsbury Road
LONDON Tel: [phone]
Note that similar products may be available from
other companies.

SuperVisor LX SECTION 0
FGAX3249400MANAA 100701 Version 1 Issue 2 0.6
WARRANTY
This unit is covered by the standard Snell & Wilcox 1-year warranty as detailed below:
Warranty
1. Snell & Wilcox warrants to the purchaser that new equipment will be free from defects in material and
workmanship for one year from the date of shipment by Snell & Wilcox, subject to the exclusions set out
below. Snell & Wilcox exclusive obligation (and purchasers only remedy) for any defect shall be to repair
or replace, at Snell & Wilcox option, at no charge except for shipping charges, any equipment or parts
returned prepaid to an approved Snell & Wilcox service center.
2. Within the warranty period, purchaser shall notify Snell & Wilcox of any defect in material or workmanship.
If a part is defective, Snell & Wilcox may forward a new part to purchaser, invoice for the part and credit
invoice upon receipt of the defective part returned, freight prepaid. Snell & Wilcox reserve the right to
inspect or repair equipment on purchaser’s premises.
3. Snell & Wilcox specifically excludes the following from warranty coverage, and assumes no responsibility
for repair or replacement thereto:
a) Equipment which has been modified, repaired or altered by procedures other than those published or
authorized in writing by Snell & Wilcox, which has been subjected to misuse, misapplication, improper
maintenance, negligence, acts beyond the purchasers control (including failure of or excessive electrical
power or failure of environmental control equipment);
b) used equipment;
c) fuses, lamps and batteries;
d) equipment which has had its serial number altered, defaced or removed.
4. No repair or replacement shall extend the warranty period.
5. NOTE: Please be certain that you have received appropriate upgrade training prior to performing
upgrades; failure to complete this training will invalidate the warranty.
6. For the warranty to be valid upgrade work must be reported by unit serial number and old cards returned in
the supplied packing plus this form correctly completed and returned.

SuperVisor LX SECTION 0
FGAX3249400MANAA 100701 Version 1 Issue 2 0.7
Table of Contents
SECTION
Section 1 General Description ....................................................................................................... 1.1
Section 2 Specifications ................................................................................................................. 2.1
Section 3 Installation
SuperVisor LX Mainframe
Mainframe Cable Links .................................................................................................... 3.1
Mainframe to Shoebox Interconnections ......................................................................... 3.1
Mainframe Connections
Power Connections............................................................................................. 3.2
Rear Panel Connections ..................................................................................... 3.4
SuperVisor LX Control Shoebox
Power Connections............................................................................................. 3.7
Rear Panel Connections ..................................................................................... 3.7
System Interface Connections ............................................................................ 3.8
Section 4 Operation
SuperVisor LX Shoebox
Powering-Up ....................................................................................................... 4.1
Display and Controls ........................................................................................... 4.2
RollCall Menu System......................................................................................... 4.4
Button Functions
Pattern ................................................................................................... 4.5
Memory .................................................................................................. 4.5
Input ....................................................................................................... 4.6
Black Level............................................................................................. 4.7
Contrast ................................................................................................. 4.7
Color ...................................................................................................... 4.7
Tint ......................................................................................................... 4.7
Enhance................................................................................................. 4.8
Size ........................................................................................................ 4.9
Select (Main Menu)................................................................................ 4.11
The Supervisor LX Operating Modes..................................................... 4.22
Section 5 RGB Input Select and Sync Level Select Notes............................................................... 5.1
Section 6 Operating the Supervisor LX Display Processor from a
remote controller using the RS422 Interface.................................................................... 6.1
Section 7 Index ................................................................................................................................ 7.1

SuperVisor LX SECTION 0
FGAX3249400MANAA 100701 Version 1 Issue 2 0.8
Manual Revision Record
Date Version No. Issue No. Change Comments
090501 1 1 First Issue
100701 1 2 Status display additions and
GBR to RGB throughout
Key Color added to menu
Complete new manual issued

SuperVisor LX SECTION 1
FGAX3249400MANAA 100701 Version 1 Issue 2 1.1
General Description
The SuperVisor LX comprises a Shoebox enclosure type LX Control and the mainframe type SuperVisor LX.
The Shoebox is designed for control desk mounting and acts as a remote control front panel for the
SuperVisor LX mainframe.
The two units are interconnected as described in Section 3, Installation
Shoebox front panel view
Shoebox rear panel view
115-230 VAC
60/50 Hz
0.2A
MADE IN UK
NETWORK SERIAL
PORT
Fuse
I
O
model
serial no.
T
1A 250V
!
CAUTION
RISK OF ELECTR IC SHOCK
DO NOT REMO VE COVERS
NO USER SERVI CEABLE PARTS
REFER SERVI CING TO QUALIFIED
PERSONNE L ONLY
SuperVisor LX Mainframe front panel view
SuperVisor LX Mainframe rear panel view

SuperVisor LX SECTION 1
FGAX3249400MANAA 100701 Version 1 Issue 2 1.2
SuperVisor LX Mainframe internal view showing position of cards
1234567891011 12 13 14 15
0 1
2
3
4
D
E
F
0 1
2
3
4
D
E
F
C
A
RD RET
A
INING PL
A
TE
SLX_IQAMMB SLX_IQDMMB SLX_IQMMFAN SLX_IQDMX4 SLX_IQD1ADC SLX_IQDMSD
AIR COOLOING CONTROL PLATE
This plate MUST be fitted
in vacant power supply slot
V1 V2
OFF
ON
Gateway
16
The functions of the cards are as follows:
Card Part No. Slot No. Function
SLX_IQAMMB 3 The IQAMMB performs analog processing of the input signal.
SLX_IQDMMB 5 The IQDMMB performs digital processing of the input signal.
SLX_IQMMFAN 7 This is a cooling fan assembly.
SLX_IQDMX4 9 The IQDMX4 is a 4 input router/switcher for both serial 4:2:2 and 4fsc
video signals.
SLX_IQD1ADC 11 The IQD1ADC converts analog component video (in either YPbPr or
RGB formats) to serial 4:2:2 format at 270 Mbit/s.
SLX_IQDMSD 14 The IQDMSD provides high quality adaptive decoding for PAL/ NTSC-M/
NTSC-J/ PAL-M/ PAL-N composite signals.
SLX_CIF3U Gateway This contains the RollCall remote control communications interface
electronics.
Option
A PC Control program (order code FGAX3249500) may be supplied.
This program allows full setup and control of the Supervisor LX from a PC. This is an optional item but it is
recommended for applications that require the chroma key facilities of the Supervisor LX. In addition to the PC
program, the CD-ROM also contains electronic versions of the Supervisor manuals.
Supplied with this option are the following:
•CD ROM
•RS232 cable 9 way to 9 way
•VGA cable 15 way to 15 way
•RS232 to RS422 converter
GATEWAY
CARD

SuperVisor LX SECTION 2
FGAX3249400MANAA 100701 Version 1 Issue 2 2.1
Specifications
Technical details are available on request; please call your local Snell & Wilcox sales office.
Dimensions

SuperVisor LX SECTION 3
FGAX3249400MANAA 100701 Version 1 Issue 2 3.1
Installation- Mainframe Cable Links
Before any installation work is carried out the 3 coaxial cable links (supplied) should be fitted to the rear panel
of the mainframe as shown below.
A
IN
B-Y/B
IN
R-Y/R
IN
Y/G
IN
V
COMPOSITE
INPUTS
DIGITAL
INPUTS
LINK A
LINK C
LINK B
Y/COMPOSITE IN
OUT H
R
B
G
COMPONENT
INPUTS
UPCONVERTER
OUTPUTS
B
COMPONENT
EXT SYNC
C IN
AUX 2 OUT
AUX 1 OUT
B
C
C
A
1 5
26
4
7
8
9
10
MADE IN HAVANT, UK
Supervisor LX
MAIN SPARE
MAINS INLET ASSIGNMENT
Note that some of the connectors have been capped; it is important that these connectors remain
capped at all times.
Installation- Mainframe to Shoebox Interconnections
115-230 VAC
60/50 Hz
0.2A
MADE IN UK
NETWORK SERIAL
PORT
Fuse
I
O
model
serial no.
T
1A 250V
!
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT R EMOVE COVERS
NO USER SERVIC EABLE PARTS
REFER SERVIC ING TO QUALIFIED
PERSONNEL ONLY
Fuse Fuse
STATUS
ROLLCALL
REMOTE
75 Ohm BNC through termination supplied
with SuperVisor LX mainframe
75 Ohm BNC through
termination supplied with Shoebox 75 Ohm BNC to BNC Cable
(not supplied)
115/230 V
60/50 Hz
2.3 A MAX
Thisdevice complies with Part 15of the FCC Rules.
Operationis subject to the following two conditions :
1, this device may not cause harmful interference, and
2, thisdevice must accept any interference received,
including interference that may cause undesiredoperation
TO REDUCE THE RISK OF ELECTRIC
SHOCKDISCONNECT T WO POWER
SUPPLY CORDS BEFORE SERVICING
THISEQUIPMENTHAS
MORE THAN O NE POWER SUPPLY CORD.
!
!CAUTION T
2.5A 250V
A
IN
B-Y/B
IN
R-Y/R
IN
Y/G
IN
V
COMPOSITE
INPUTS
DIGITAL
INPUTS
LINK A
LINK C
LINK B
Y/COMPOSITE IN
OUT H
R
B
G
COMPONENT
INPUTS
UPCONVERTER
OUTPUTS
B
COMPONENT
EXT SYNC
C IN
AUX 2 OUT
AUX 1 OUT
B
C
C
A
1 5
26
4
7
8
9
10
MADE IN HAVANT, UK
Supervisor LX
MAIN SPARE
MAINS I NLET ASSI GNMENT

SuperVisor LX SECTION 3
FGAX3249400MANAA 100701 Version 1 Issue 2 3.2
Supervisor LX Mainframe Connections
POWER CONNECTIONS
Power Supply
There are two filtered IEC connectors with integral
fuse holders for the connection of mains power to
the unit. The fuse rating for each connector is
2.5 A (T).
The unit can accommodate two separate supplies
and the position of the connectors coincides with
the position of the power supply modules.
If only one PSU module is to be installed it should
be fitted in the position marked MAIN. The unit will
operate correctly when power is connected to
connector marked MAIN.
Fitting and powering-up a second power supply
module in the position marked SPARE will provide
continued operation if the MAIN power supply
module should fail.
When two power supply modules are fitted both
IEC connectors can be connected to the same or
different power sources.
Note that the power outlet(s) supplying power to
the unit should be close to the unit and easily
accessible
The power supply module(s) are Snell & Wilcox
generic type SHDPSUA15.
Caution! The fan ventilation hole above the mains
inlet connector must not be obscured.
Fuse Fuse
AC INPUT
100-240V~50/60 Hz
1.2A MAX
FUSE 2.5 A(T)

SuperVisor LX SECTION 3
FGAX3249400MANAA 100701 Version 1 Issue 2 3.3
REMOTE
This 9 pin `D' connector on the rear panel supports
RS422. This allows the unit to be connected to a
control device, usually the associated PC.
Control is via an RS232 port of the PC with
Windows 95/98/NT Based Supervisor LX Control
Software using the supplied cable and adapter.
Connections
9-way Connector FUNCTION
1 Frame Ground
2 Transmit A (Tx-)
3 Receive B (Rx+)
4 Receive Common
5 [No connection]
6 Transmit Common
7 Transmit B (Tx+)
8 Receive A (Rx-)
9 Frame Ground
RollCall
This single BNC connector will allow the unit to be
connected to the RollCall™ network
communications system.
Note that the Supervisor LX is supplied with a
75 Ohm BNC through terminator.
The maximum length of cable used for the RollCall
connection depends on the type of cable used.
For example:
PSF1/2M, Belden 8281 = 400 m
PSF1/3M, RG59 = 270 m.
9 Pin D to 9 Pin D
Cable (Supplied)
RS422 to RS232
Adaptor (Supplied)
ROLLCALL
REMOTE
RS422
RS232
Fuse
ROLLCALL
REMOTE

SuperVisor LX SECTION 3
FGAX3249400MANAA 100701 Version 1 Issue 2 3.4
REAR PANEL SIGNAL CONNECTIONS
Decoder Section
The decoder accepts a composite input or a
separated input in either NTSC or PAL standard
via BNC connectors.
COMPOSITE INPUTS
The Y/Composite IN connector is used for the
composite video input to the decoder via a BNC
connector terminated in 75 Ohms. This should be
used for sources of standard composite video
signals.
Nominal input level is 1V p-p.
S-VHS, Hi 8 Separated Video inputs
The Y/COMPOSITE IN connector and the C IN
Input connectors are used for sources of S-VHS,
Hi 8 or other sources of separated Video signals.
The C IN Input should be used for C
(Chrominance) signal and the Y/COMPOSITE IN
connector used for the Y (Luminance) signal.
Both connections are via BNC connectors and are
terminated in 75 Ohms.
Note that a 4 pin Mini-DIN plug to 2 BNC plugs is
supplied for connecting to S-VHS, Hi 8 etc.
sources of video.
White = Y (Luminance), Red = C (Chrominance)
Nominal Y input level is 1V p-p and the C input is
for standard color burst level.
Additional cables may be obtained in the UK from:
COMPOSITE VIDEO LTD
Unit 3
Four Seasons Crescent
Kimpton Road
Sutton
Surrey Tel: [phone]
Note that similar products may be available from
other companies.
AUX 1 OUT
This is a component digital output of the decoder
via a BNC connector for 75 Ohms.
COMPOSITE
INPUTS
Y/COMPOSITE INC IN
AUX 1 OUT

SuperVisor LX SECTION 3
FGAX3249400MANAA 100701 Version 1 Issue 2 3.5
COMPONENT INPUTS
These inputs normally accept analog component
video signals in YPbPr format via BNC connectors
that terminate in 75 Ohms.
Note that this input may be configured to accept an
RGB signal.
On early cards this is by link selection on the
IQD1ADC card.
For full details please see Section 5 “RGB input
select change and Sync level select”.
On later cards this is achieved by software control.
See Section 4, “Operation”.
COMPONENT EXT SYNC
When External syncs are selected for the analog
component signal above, the ADC will lock to a
suitable sync signal connected to the IN connector.
The OUT connector provides a buffered version of
the signal at the IN connector.
This input normally accepts a low level 0.3 V p-p
signal. It can be configured to accept a high level
2 V p-p signal.
For full details please see Section 5 “RGB input
select change and Sync level select”.
AUX 2 OUT
This is a component digital output of the ADC via a
BNC connector for 75 Ohms.
DIGITAL INPUTS
These are component digital inputs to the router
section of the unit via BNC connectors that
terminate in 75 Ohms. These signals may be
selected using either the Shoebox or the PC
Control program.
AUX 2 OUT
This is the component digital output of the router
section of the unit via a BNC connector for 75
Ohms.
B-Y/B
IN
R-Y/R
IN
Y/G
IN
COMPONENT
INPUTS
IN
OUT
COMPONENT
EXT SYNC
AUX 2 OUT
DIGITAL
INPUTS
AUX 2 OUT

SuperVisor LX SECTION 3
FGAX3249400MANAA 100701 Version 1 Issue 2 3.6
COMPUTER VIDEO INPUT
Input signals from a computer source may be
connected to the unit using this 15-pin mini `D' type
connector. The connections are compatible with
computers using the same type of connector for
IBM (or compatible) CGA, VGA and SVGA signals.
In HDTV thru’ mode connections are routed
straight through.
Mode
Pin No. VGA Key/VGA Thru’ HDTV Thru’
1 Red Video Pr Video
2 Green Video Y Video
3 Blue Video Pb Video
4 Ground Ground
5 Ground Ground
6 Red Ground Pr Ground
7 Green Ground Y Ground
8 Blue Ground Pb Ground
9 Not Used Not Used
10 Ground Ground
11 Ground Ground
12 Not used Not used
13 H-Sync Thru’
14 V-Sync Thru’
15 Not used Not used
UPCONVERTER OUTPUTS
RGB
Component RGB outputs are available from these
BNC connectors at 75 Ohms impedance.
Signal levels are non-composite 0.7V p-p into 75
Ohms.
H and V
Horizontal and vertical synchronizing pulses are
available from these BNC connectors.
Signal levels are standard TTL.
Additional SVGA Interface cables are available
from:
VIDEK
Kingsbury Trading Estate
Kingsbury Road
LONDON Tel: [phone]
Note that similar products may be available from
other companies.
V
H
R
B
G
UPCONVERTER
OUTPUTS

SuperVisor LX SECTION 3
FGAX3249400MANAA 100701 Version 1 Issue 2 3.7
Installation- LX Control Shoebox
POWER CONNECTIONS
This is the mains power connector suitable for a
standard IEC type power cord and contains a
1 A(T) 250 V fuse and a spare fuse.
To gain access to the fuses the tab on the right
hand side of the connector assembly should be
lifted. Always replace the fuses with the same type.
If a plug is fitted to the power cord a fuse of 5A
(Fast) should be installed.
The Power On/Off switch is an integral part of this
connector assembly. Press Ito switch ON, press O
to switch OFF.
Power ON will be indicated by the illumination of
the LED on the front panel.
NETWORK CONNECTOR
This 9 pin `D' connector has no function on this
unit.
Do not make connections to this connector.
BNC CONNECTOR
This single BNC connector allows the unit to be
connected to, and communicate with, the
Supervisor LX mainframe.
See page 3.1 for interconnection details.
SERIAL PORT
This 9 pin `D' connector has no function on this
unit.
Do not make connections to this connector.
115-230 VAC
60/50 Hz
0.2A
Fuse
I
O
T
1A 250V
NETWORK
NETWORK
SERIAL
PORT
Lift Tab to
access fuses

SuperVisor LX SECTION 3
FGAX3249400MANAA 100701 Version 1 Issue 2 3.8
SYSTEM INTERFACE CONNECTIONS

SuperVisor LX SECTION 4
FGAX3249400MANAA 100701 Version 1 Issue 2 4.1
Operation
IMPORTANT-POWERING-UP
When the ShoeBox controller is powered up it will
attempt to connect to a mainframe unit. The
following message will be seen:
When a connection to a mainframe unit has been
established the following message is displayed as
the ShoeBox controller initializes itself.
If the physical connection to the mainframe is lost
then the ShoeBox controller will attempt to
re-establish a connection. This process should be
fully automatic.
Note that there may be rare occasions when the
ShoeBox controller does not complete the
initializing process. Should this happen the Home
button should be pressed. This will force the
ShoeBox controller to re-initialize.
Note that the same effect as a power cycle for the
Shoebox can be achieved by simultaneously
pressing the buttons marked 4 and Tint on the
Shoebox front panel and selecting Yes in the
display screen
Searching for unit:
0000:40:05
Please wait...
Restart Panel!
Are you sure?
◀
◀◀
◀ Yes No▶
05 : IQD1MMB