Sole Diesel 85 GT User manual

U_GNBL_EN
Rev. 2

INTRODUCCION
2
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017

INTRODUCTION
3
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
Introduction
Presentation
Dear Customer,
First, we would like to thank you for choosing a Solé Diesel product. We recommend that
you read this manual carefully before carrying out any of the operations and keep it close at hand,
near the genset, as it can be of great use in the future.
Our goal as a manufacturing company is that you enjoy our product, regardless of the use
you make of it. The equipment manufactured in Solé Diesel facilities is designed to offer the highest
performance in the most demanding operating conditions.
The images, text and information contained in this manual are based on the product’s
features at the time of publication. Solé Diesel reserves the right to modify this document without
prior notice
Abbreviations
BTDC: Before Top Dead Center
ATDC: After Top Dead Center
BBDC: Before Bottom Dead Center
ABDC: After Bottom Dead Center
API: American Petroleum Institute
ACEA: European Automobile Manufacturers’ Association
ASTM: American Society for Testing Materials
TBD: To Be Determined
Units of measurement
Measurements are based on the International System of Units (SI), and their converted
metric values are indicated in parentheses (). For metric conversion, the following rates are used
-Pressure: 1 Pa = 1,0197 · 10-5 kgf/cm2= 1 · 10-5 bar
-Torque: 1 Nm = 0,10197 kgf·m
-Force: 1 N = 0,10197 kgf
-Power: 1 W = 1,341 · 10-3 HP

TABLE OF CONTENTS
4
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
Table of Contents
Introduction 1
Table of Contents..............................................................................................................................................4
Safety Precautions and Instructions ...............................................................................................................6
Genset labels.................................................................................................................................................8
Solé Diesel warranty........................................................................................................................................10
Solé diesel limited warranty .................................................................................................................................... 10
Solé Diesel extended warranty .............................................................................................................................. 10
Restrictions ................................................................................................................................................................. 11
Responsibilities........................................................................................................................................................... 12
After-sales service contact ..................................................................................................................................... 12
Service Assistance .................................................................................................................................................... 13
Section 1 - Genset Information .....................................................................................................................14
1.1. Genset Identification....................................................................................................................14
1.2. Genset Parts Identification ..........................................................................................................15
1.3. Genset Limited Warranty ...................................................................................................................16
RESTRICTIONS............................................................................................................................................................. 16
Section 2 - Transport, Handling and Storage..............................................................................................17
2.1. Reception .............................................................................................................................................17
2.2. Transporting and Handling the Packed Genset............................................................................17
2.3. Transporting and Handling the Unpacked Genset.......................................................................18
2.4. Storage of Packed and Unpacked Genset ...................................................................................18
Section 3 –Installation ....................................................................................................................................19
3.1. Angle of Installation......................................................................................................................19
3.2. Genset installation ........................................................................................................................19
Section 4 - Operation .....................................................................................................................................20
4.1. Prestart Checklist...........................................................................................................................20
4.2. Genset Operation at Low Temperatures ........................................................................................20
4.3. Winterzation and Preservation ..........................................................................................................21
4.4. Maintenance during the storage.....................................................................................................22
4.5. Restoration of Operational Conditions............................................................................................22
Section 5 - Systems and Scheduled Maintenance ...................................................................................23
5.1. Operating Description ........................................................................................................................23
5.2. Periodic Maintenance Schedule......................................................................................................23
5.3. General .................................................................................................................................................25
MAINTENANCE TASK. SCREW TIGHTENING, FASTENINGT..................................................................................... 25
MAINTENANCE TASK. VALVE CLEARANCE INSPECTION ...................................................................................... 25
INSPECTION................................................................................................................................................................ 25
MAINTENANCE TASK. COMPRESSION PRESSURE INSPECTION............................................................................. 26
5.4. Lubrication System ..............................................................................................................................27
CIRCUIT DESCRIPTION............................................................................................................................................... 27
OIL SPECIFICATIONS.................................................................................................................................................. 27
MAINTENANCE TASK. OIL FILTER CHANGE............................................................................................................. 27
MAINTENANCE TASK. OIL LEVEL CHECK ................................................................................................................ 28
MAINTENANCE TASK. OIL FILL / CHANGE .............................................................................................................. 28
5.5. Fuel System ...........................................................................................................................................29
CIRCUIT DESCRIPTION............................................................................................................................................... 29
FUEL SPECIFICATIONS ............................................................................................................................................... 29

TABLE OF CONTENTS
5
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
MAINTENANCE TASK. FUEL LEVEL INSPECTION ...................................................................................................... 29
MAINTENANCE TASK. FUEL TANK CLEAN................................................................................................................ 29
MAINTENANCE TASK. WATER SEPARATOR FILTER PURGUE .................................................................................. 30
MAINTENANCE TASK. FUEL FILTER CHANGE........................................................................................................... 30
MAINTENANCE TASK. INJECTION PUMP INSPECTION ........................................................................................... 30
MAINTENANCE TASK. INJECTOR INSPECTION........................................................................................................ 30
5.6. Cooling System ....................................................................................................................................31
COOLANT CIRCUIT DESCRIPTION ........................................................................................................................... 31
SEAWATER CIRCUIT DESCRIPTION........................................................................................................................... 31
COOLAN SPECIFICATIONS....................................................................................................................................... 31
MAINTENANCE TASK. COOLANT CHECK............................................................................................................... 32
MAINTENANCE TASK. COOLANT FILL / CHANGE.................................................................................................. 32
MAINTENANCE TASK. SEAWATER FILTER INSPECTION ........................................................................................... 32
MAINTENANCE TASK. SEAWATER PUMP IMPELLER INSPECTION.......................................................................... 32
MAINTENANCE TASK. ZINC ANODE INSPECTION .................................................................................................. 33
5.7. Inlet and Exhaust System....................................................................................................................33
EXHAUST CIRCUIT DESCRIPTION .............................................................................................................................. 33
MAINTENANCE TASK. AIR FILTER INSPECTION........................................................................................................ 34
MAINTENANCE TASK. EXHAUST GAS, NOISE AND VIBRATIONS INSPECTION ..................................................... 34
5.8. Electrical System ..................................................................................................................................35
BATTERY ...................................................................................................................................................................... 35
CIRCUIT PROTECTION ............................................................................................................................................... 35
MAINTENANCE TASK. STARTER MOTOR INSPECTION ............................................................................................ 35
MAINTENANCE TASK. ALTERNATOR BELT TENSION INSPECTION.......................................................................... 36
MAINTENANCE TASK. BATTERY LEVEL...................................................................................................................... 36
5.9. Alternator ..............................................................................................................................................36
MAINTENANCE TASK. CONTROL OF WINDINGS AND ELECTRICAL INSULATION............................................... 36
MAINTENANCE TASK. CONTROL OF BEARINGS .................................................................................................... 36
MAINTENANCE TASK. CLEANING AND LUBRICATION .......................................................................................... 37
Section 7 - Troubleshooting ...........................................................................................................................38
Section 8 –Technical Specifications............................................................................................................45
Section 9 –Tightening Torques......................................................................................................................47
Section 10 –Technical Appendices.............................................................................................................48
10.1. Wiring diagrams .................................................................................................................................49
OPERATION ................................................................................................................................................................ 50
START THE GENSET ..................................................................................................................................................... 51
STOP THE GENSET....................................................................................................................................................... 51
10.2. Alternator connections ....................................................................................................................55
10.3. Regulator connections.....................................................................................................................57
10.4. Overall dimensions ............................................................................................................................59
10.5 Sensor data..........................................................................................................................................62
10.6 Alarm list ...............................................................................................................................................63
Fault indicator lamp................................................................................................................................................. 63
Diagnostic button and Fault indicator lamp........................................................................................................ 64
Section 11 - Instructions to Replace and Remove ....................................................................................71
Inspection prior to the delivery of propulsion engines..............................................................................72
Maintenance Log............................................................................................................................................73

SAFETY PRECAUTIONS AND INSTRUCTIONS
6
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
Safety Precautions and Instructions
Solé Diesel is concerned for your safety and your machine’s condition. Safety Precautions
and Instructions are one of the primary ways to call your attention to the potential hazards
associated with our engine operation. Follow the precautions listed throughout the manual before
and during operation and maintenance procedures for your safety, the safety of others and the
performance of your engine.
Types of Safety Precautions:
Indicates the presence of a hazard that can cause severe personal injuries, death or
substantial property damages.
Indicates the presence of a hazard that will or can cause minor personal injuries or property
damages.
Communicates installation, operation and maintenance information that is safety related
but not hazard related.
Servicing the fuel system and combustible materials. A flash fire can cause severe injury or
death.
Do not smoke or permit flames or sparks near the fuel injection system, fuel line, fuel
filter, fuel pump, or other potential sources of spilled fuels or fuel vapours. Never add
fuel to the tank while the genset is running because spilled fuel may ignite on contact
with hot parts or from sparks.
Catch fuels in an approved container when removing the fuel line or fuel system. Keep the fuel
lines and connections tight and in good condition. Do not replace flexible fuel lines with rigid lines
and use flexible sections to avoid fuel line breakage caused by vibrations.
Keep the compartment and the genset clean and free of debris to minimize the risk of fire.
Servicing the air cleaner. A sudden backfire can cause severe injury or death.
Do not operate the genset with the air cleaner/silencer removed.

SAFETY PRECAUTIONS AND INSTRUCTIONS
7
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
Combustible materials. A fire can cause severe injury or death.
Genset fuels, fuel vapours and combustible materials are flammable and explosive.
Handle these materials carefully to minimize the risk of fire or explosion. Equip the
compartment or nearby area with a fully charged fire extinguisher. In case of fire do
not open sound, shield compartment and follow these instructions:
-Shut down genset(s).
-Continuously discharge entire contents of a halon or CO2portable fire
extinguisher (or other provision) immediately.
Carbon monoxide (CO) can cause severe nausea, fainting or death.
Genset exhaust gases contains carbon monoxide gas. Carbon monoxide is an
odourless, colourless, tasteless, no irritating gas that can cause death if inhaled
for even a short time.
Get fresh air and do not sit, lie down or fall asleep if anyone shows signs of
carbon monoxide poisoning:
-Light-headedness, dizziness.
-Physical fatigue, weakness in joints and muscles. Sleepiness, mental fatigue, inability to
concentrate or speak clearly, blurred vision. Stomachache, vomiting, nausea.
Keep the area around the battery well ventilated. While the genset is running or the battery
is charging, hydrogen gas is produced which can be easily ignited.
Never allow battery fluid (battery contains sulfuric acid) to come in contact with
clothing, skin or eyes. Always wear safety gloves and protective clothing when
servicing the battery. If battery fluid contacts the eyes and/or skin, immediately flush
the affected area with a large amount of clean water and obtain prompt medical
treatment.
Moving parts. Keep hands, feet, hair, clothing and test leads away from
the belts and pulleys when the genset is running. Replace guards,
screens and covers before operating the genset.
Before working on the genset or connected equipment, disable the genset as follows:
Set the genset controller (SCO) to OFF Mode.
(1) Disconnect the power input from battery.
(2) Disconnect the battery cables. Remove the negative (-) lead first when
disconnecting the battery. Reconnect the negative (-) lead last when reconnecting
the battery.
Follow these precautions to prevent the starting of the genset by genset controller (SCO),
remote start/stop switch, or genset start command from a remote computer.

SAFETY PRECAUTIONS AND INSTRUCTIONS
8
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
Never remove the cooler cap if the genset is hot. Steam and hot genset coolant
will spurt out and seriously burn you. Allow the genset to cool down before you
attempt to remove the cooler cap.
Read the genset operator's manual and understand it before operation and maintenance
of the genset, to ensure that it continues operating practices and maintenance procedures.
Hearing protection. Use to avoid hearing loss when handling the motor.
1. The installer / operator of the genset has to wear suitable CLOTHING for the workplace and
the situation; in particular, avoid loose clothes, chains, bracelets, rings and all accessories
that could become entangled with moving parts.
2. The installer / operator of the genset has to wear personal protective equipment such as
gloves, work shoes, eye and hearing protection as required by the task.
3. The area in which the operator is working has to be kept tidy and free of oil and other liquid
spillages and solid waste (metal chips, etc.).
Genset labels
If the genset does not turn after several attempts to crank
may cause water entering the genset. In this situation it is
recommended:
1) Close the seacock.
2) Drain the water from the exhaust system in the
water trap.
3) Do not try to restart the genset until the cause of
the start fail is identified.
The genset and the gearbox are supplied without any fluid
inside. Consult the manual to follow the installation procedure
and commissioning as well as the fluid capacity - coolant, oil
and oil of gearbox.
Read the genset operator's manual and understand it before operation and maintenance of the
genset, to ensure that it continues operating practices and maintenance procedures insurance.

SAFETY PRECAUTIONS AND INSTRUCTIONS
9
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
Dangerous voltage.Operate the genset only when all
guards and electrical panels are ready.
Hot parts, coolant and steam. Stop the genset and let it
cool down before touching or removing any genset part.
Moving parts. Keep hands, feet, hair, clothing and test
leads away from the belts and pulleys when the genset is
running. Replace guards, screens and covers before
operating the genset.
Heavy material. Genset is a heavy element, use the right tools for transportation and handling.
Do not use the motor as a step. Use it as a step can cause genset damage plus cause undesired
operation.
Connection point of the battery cables to the genset. Red cable (positive)
and black cable (negative).
Identification on the genset of the coolant fill cap. See
section 6.6. Refrigeration system.
Identification on the genset of the lubricating oil fill plug. See section 6.4.
Lubrication system.
Tag line installation genset exhaust, above and below the waterline. See 6.7. Intake and
exhaust system.

SOLÉ DIESEL WARRANTY
10
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
Solé Diesel warranty
Read the manual and documents delivered with each engine before carrying out any of
the operations or presenting any queries. The engine is supplied without any liquids. Ensure that
the liquids used match the specifications contained in Solé Diesel manuals.
The application of the conditions described in this document shall only be effective for
engines or generator sets that have been invoiced after January 1, 2012.
Solé diesel limited warranty
Solé Diesel guarantees that at the time of shipment all its engines and generator sets
comply with the provided specifications and do not have any manufacturing defects.
The limited warranty provided by Solé Diesel enters into force from the time of sale to the
firs end-purchaser or user of the engine or generator ser. In the event that the product is not
immediately delivered to the end-customer, the warranty shall enter into force 6 months after the
date of sale. Any limited warranty period that has not elapsed can be transferred to the following
purchaser (s).
Unless authorised otherwise by Solé Diesel, the warranty periods are applied according to
the time elapsed in months from the date of purchase or the limit of hours of operation
(whichever occurs first) listed in the following table:
Solé Diesel extended warranty
Solé Diesel an extended period of coverage for the following components: engine block,
cylinder head, crankshaft, camshaft, flywheel housing, timing gear housing, timing gear, conrod.
Limited Warranty Coverage Periods
Product
Pleasure
Work
Months
Hours
Months
Hours
Propulsion Engines
24
1000
12
2000
Generator Sets
24
1000
12
1000
Extended Coverage Periods
Product
Pleasure
Work
Months
Hours
Months
Hours
Propulsion Engines
36
1500
-
-
Generator Sets
36
1000
-
-

SOLÉ DIESEL WARRANTY
11
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
Restrictions
Coverage:
a) The warranty covers any failure of the product under normal opera- ting conditions
caused by a defect in manufacturing.
b) The warranty covers the labour costs necessary to replace and/or repair the defective
original components, according to Solé Diesel standards of excellence. The time period
covered for these operatio- ns is limited to 4 hours.
c) The warranty covers reasonable costs of travel required to carry out the necessary
operations. The travel distance is limited to 300 kilome- tres in conjunction to a travel time
of 3 hours.
Excluded from coverage:
a) If Solé Diesel products are installed and used alongside other products not designed or
manufactured by Solé Diesel that affect their operation, the warranty shall apply
exclusively to the Solé Diesel products and shall not apply if the products from another
manufacturer are inappropriate for use alongside Solé Diesel products or are the cause
of the failure or poor operation of our products.
b) The warranty shall not apply if the revisions and maintenance services indicated in the
User and Maintenance Manuals have not been adhered to properly. In case of
implemented warranty, supporting document of the revisions and maintenance service
should be exhibited, proving the requirements outlined in the manuals have been
followed.
c) Deterioration resulting from time of storage exceeding 6 months and/or storage
conditions that do not comply with the procedures described in the User and
Maintenance Manuals.
d) Deterioration resulting from not complying with the procedure for winter storage while
the engine is not in service, as described in the User and Maintenance Manuals.
e) Faults due to negligence, lack of service, accidents, abnormal use and inadequate
service or installation.
f) Faults due to the use of components not manufactured or sold by Solé Diesel.
g) Faults due to electrical installations that do not comply with Solé Diesel design
specifications or are not expressly approved by Solé Diesel.
h) Faults due to the use of and operation with fuels, oils or lubricants that are not authorised
by Solé Diesel.
i) Faults due to water entering the cylinder(s) through the exhaust system.
j) Faults in propulsion engines due to the use of a propeller that is inadequate for the load
or application. We recommend contacting Solé Diesel to consult the choice of the
correct propeller(s).
k) Failure for general omission of the procedures described in the User and Maintenance
Manuals.
l) Components subjected to normal operating wear and tear.

SOLÉ DIESEL WARRANTY
12
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
m) Costs due to phone communications, loss of time or money, discomfort, launching,
grounding, removal or replacement of vessel parts or materials because the design of
the vessel makes it neces- sary to do so to access the engine, and damage and/or
accidents caused as a result of a failure.
Responsibilities
Responsibilities of the manufacturer:
The obligations of Solé Diesel are restricted to repairing the defecti- ve parts or, IF
DEEMED APPROPRIATE BY SOLÉ DIESEL, returning the amount of the purchase or replacing the
parts to prevent poor operation resulting from defective materials or faults in the manu-facture
covered by the warranty.
Solé Diesel reserves the right to modify the design of any of its products without taking on
any obligation to modify a product that has been manufactured previously.
This manual, as well as technical documentation, manuals or pamphlets may
undergo modifications without prior notice.
Responsibilities of the purchaser:
The purchaser shall be responsible for the care, operation and maintenance of the
product in compliance with the contents of the User and Maintenance Manuals. The purchaser
shall provide proof of all the maintenance services performed on the product. The costs of said
services and that of the components and liquids replaced during said services shall be at the
expense of the purchaser.
The maintenance operations described in this manual shall be performed during the
Warranty Contract Periods (Limited and Extended Coverage) by an AUTHORISED SOLÉ DIESEL
DEALER. Non-compliance with this condition shall void the warranty in all its terms. In such an
event, the materials (oil, filters, etc.) and labour involved shall be at the expense of the purchaser.
The purchaser should keep the invoice of the work performed as proof.
If the service is not covered by the warranty, the purchaser must pay for all labour
performed, the associated materials and any other expense related to the service.
All shipments of products or components sent by the purchaser for inspection and repair
shall be paid in advance by the purchaser.
After-sales service contact
Claims shall be presented during the warranty period to the nearest authorised Solé
Diesel dealer (see chart of Solé Diesel Dealers), who shall take care the service covered by the
warranty.
The purchaser must provide proof of purchase and date of purchase by presenting the
authorised dealer with an original copy of the Warranty Registry Card. If this is not available, the
purchaser must provide a copy of the purchase invoice of the product in question. Claims under
warranty shall not be dealt with by the dealer until the date of purchase has been verified.
The following information must also be provided by the purchaser:
a) Owner’s name, address and contact telephone number.
b) Product model and serial number.
c) Number of service hours of the product.

SOLÉ DIESEL WARRANTY
13
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
d) Detailed description of the problem.
e) Information regarding any repair or installation performed by a service not included in
the Solé Diesel distribution network, as well as the services performed.
Service Assistance
For an updated list of our distribution network, visit Dealers section in our web page
www.solediesel.com.
Or request this information by contacting Solé Diesel at:
e-mail: [email protected]
Phone: [phone]

GENSET INFORMATION
14
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
Section 1 - Genset Information
1.1. Genset Identification
IDENTIFICATION LABEL:
The nameplate is located above the rocker cover. The
characteristics plate of genset it’s located above the
alternator case.
The characteristics plate of canopy genset it’s located outside, as shown in the following picture:
GENSET SERIAL NUMBER:
In addition, all gensets are marked with the serial number on the block, on the fuel injection pump.
The standard genset can operate at temperatures between -18 ° C and + 45 ° C.

GENSET INFORMATION
15
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
1.2. Genset Parts Identification
PIECE
ELEMENT
1
Oil filter
2
Oil drain plug
3
Dipstick
4
Oil filler cap
5
Oil cooler
6
Fuel filter
7
Fuel feed pump
8
Injection pumps
9
Injectors
10
Valves
11
Fuel overflow valve
12
Air cooled (only in 115
GT/GTC and 120
GTA/GTAC)
13
Admission manifold
14
Exhaust manifold
15
Turbocharger
16
Air filter (only standard
version)
17
Se water pump
18
Coolant water pump
19
Heat exchanger
20
Expansion tank
21
Anode (anti-corrosion
protection)
22
Coolant drain plug
(engine)
23
Coolant drain plug
(expansion tank)
24
Coolant drain plug
(heat exchanger)
25
Coolant filler cap
26
Starter motor
27
Alternator 24V
28
Alternator belt
29
Coolant pump and
fuel feed pump belt
30
Vibration damper
31
Governor
32
Stop solenoid
34
Wet exhaust elbow

GENSET INFORMATION
16
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
1.3. Genset Limited Warranty
The limited warranty provided by Solé Diesel enters into force from the time of sale to the first
end-purchaser or user of the genset. In the event that the product is not immediately delivered to
the end-customer, the warranty shall enter into force 6 months after the date of sale. Any limited
warranty period that has not elapsed can be transferred to the following purchaser(s).
Unless authorized otherwise by Solé Diesel, the warranty period is applied according to the
time elapsed in months from the date of purchase or the limit of hours of operation (whichever
occurs first).
GENSET FOR
PROFESSIONAL USE
GENSET FOR
RECREATIONAL USE
MONTHS
HOURS
MONTHS
HOURS
LIMITED WARRANTY COVERAGE PERIODS
12
2000
24
1000
EXTENDED COVERAGE PERIODS
-
-
24
1000
Extended coverage (only recreational gensets) is applied to the following components:
-Genset block
-Cylinder head
-Crankshaft
-Camshaft
-Flywheel housing
-Timing gear housing
-Timing gear
-Connecting rod
RESTRICTIONS
Coverage:
a) The warranty covers any failure of the product under normal operating conditions
caused by a defect in manufacturing.
b) The warranty covers the labor costs necessary to replace and/or repair the defective
original components, according to Solé Diesel standards of excellence. The time period
covered for these operations is limited to 4 hours.
c) The warranty covers reasonable costs of travel required to carry out the necessary
operations. The travel distance is limited to 300 kilometers in conjunction with a travel time
of 3 hours.
To see EXCLUDING COVERAGE and more information about responsibilities and more,
consult the Warranty Manual.

TRANSPORT, HANDLING AND STORAGE
17
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
Section 2 - Transport, Handling and Storage
2.1. Reception
When the genset is delivered make sure that the packing has not been damaged during
transport and that it has not been tampered with or that components inside the packing have
been removed (see information marked on covers, bases and cartons).
Place the packed genset as close as possible to the place of installation and remove the
packing material, checking that the goods supplied correspond to the order specifications.
If you notice damage or missing parts, inform SOLÉ S.A. after-sales departments and the
carrier immediately and forward photographic evidence of the damage.
After inspecting the goods if you notice damage, write a reservation on the delivery note.
Have the carrier countersign the note and advise SOLÉ S.A., preferably by mail
([email protected]).
2.2. Transporting and Handling the Packed Genset
When lifting and transporting the genset use EXCLUSIVELY a forklift or bridge crane of
appropriate load capacity, with chains equipped with safety hooks suitable for lifting the load.
The use of any other system automatically invalidates the insurance guarantee against
possible damage to the genset.
To unpack the genset, you must follow these steps:
1. Remove the cardboard crate.
2. Lift the genset using a forklift and suitable
chains, which hook to the genset
eyebolts.
3. Transfer the genset to the intended
position of installation.
4. Remove the wooden base.
5. Begin installation operations.

TRANSPORT, HANDLING, AND STORAGE
18
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
2.3. Transporting and Handling the Unpacked Genset
When the genset is unpacked and ready for transport, use EXCLUSIVELY the appropriate
lifting eyebolts.
2.4. Storage of Packed and Unpacked Genset
If the genset is left idle for prolonged periods, the client must check the possible conditions
of conservation in relation to the place of storage.
If the genset is unused for prolonged periods and stored, observe all the relative technical
specifications.
The treatment of the genset for storage is guaranteed for 6 months after the time of delivery (as
specified in Section 1.3 or in the Warranty Manual).
If the user decides to start the genset after a long-time period, this must be done in the
presence of an authorized technic.
A
DETALLE A
B
DETALLE B
C
DETALLE C

INSTALLATION
19
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
Section 3 –Installation
3.1. Angle of Installation
Make sure the genset is installed on a level surface. Otherwise, the following angular
operation maximum is permitted:
If the genset operates in these conditions, check Section 5.4. Lubrication System.
3.2. Genset installation
Follow these steps to install the genset:
1. FIX GENSET. See 10.4 Genset Dimensions (mounting holes) and section 9 Tightening Torques.
2. CONNECT EXHAUST OUTLET. See 10.4 Genset Dimensions.
1. WET EXHAUST OUTLET
2. DRY EXHAUST OUTLET + SEAWATER OUTLET
3. CONNECT SIPHON BREAKER. (if installed) See 10.4 Genset Dimensions.
4. CONNECT SEAWATER INLET. See 10.4 Genset Dimensions.
5. CONNECT FUEL INLET. See 10.4 Genset Dimensions.
6. CONNECT LEAK COOLANT OUTLET. See 10.4 Genset Dimensions.
7. FILL WITH OIL. See 5.4 Lubrication System.
8. FILL WITH COOLANT. See 5.6 Cooling System.
9. CHECK EACH PIPE CONNECTION for oil or coolant leaks.
10. CONNECT TO EARTH. See 5.5 Fuel System.
11. PRIME THE FUEL SYSTEM. See 5.5 Fuel System.
12. CONNECT TO SCO PANEL. See Section 10.4 Genset Dimensions.
13. CONNECT TO BATTERY. Follow label battery connection into the genset.
It is necessary to install a waterlock (supplied as accessory) in the exhaust system to avoid
water ingestion (See section 6.7).
Model
Continuously
85 GT/GTC - 100 GTA/GTAC - 115 GT/GTC -
120 GTA/GTAC
10º

OPERATION
20
Operator’s Manual Marine Diesel Gensets
Revision 2. 10/2017
Section 4 - Operation
4.1. Prestart Checklist
Follow these checks and inspections to ensure the correct genset operation. In addition,
some checks require verification after unit starts.
AIR CLEANER: Check for a clean and installed air cleaner element to prevent unfiltered air
from entering the genset.
AIR INLETS:Check for clean and unobstructed air inlets.
BATTERY: Check for tight battery connections.
COOLANT LEVEL: Check the coolant level according to coolant circuit capacity.
DRIVE BELTS: Check the belt condition and tension of the coolant pump and battery
charging alternator belt.
EXHAUST SYSTEM: Check for exhaust leaks and blockages. Check the silencer and piping
condition and check for tight exhaust system connections.
Check that the exhaust outlet is unobstructed.
FUEL LEVEL: Check the fuel level and keep the tank(s) full to ensure adequate fuel supply.
OIL LEVEL: Maintain the oil level below dipstick high mark and above dipstick low mark.
OPERATING AREA: Check for obstructions that could block the flow of admission air.
SEAWATER PUMP PRIMING: Prime the seawater pump before initial startup. To prime the
pump:
-Close the seacock.
-Remove the hose from the seawater-filter outlet.
-Fill the hose and seawater pump with clean water.
-Reconnect the hose to the water filter outlet.
-Open the seacock.
Confirm seawater pump operation on startup as indicated by water discharge from the
exhaust outlet.
4.2. Genset Operation at Low Temperatures
Whenever the atmospheric temperature drops below zero, the following series of
circumstances occur:
The cooling liquids may freeze.
The oil becomes thicker.
There is a drop in the voltage at the battery terminals.
The inlet air temperature is low and the genset has difficulty in starting.
The fuel loses fluidity.
To prevent the damage caused by low temperature operation, the genset should be
prepared:
1. Use special low temperature coolant or suitable anti-freezing agent concentration.
2. Close the seawater cock, when the genset is stopped. Open the seawater filter cover
and start the genset adding a mixture of freshwater and suitable anti-freezing agent
concentration (see package labels) until the seawater circuit is filled completely. Stop