Solid Wood Kitchen Cabinets Slimline D450mm User manual

Assembly Guide
300mm - 600mm Wide Slimline Base Cabinet D450mm
IMPORTANT – Please read prior to installation
Thanks for purchasing a solid oak kitchen cabinet. Before you commence installation, please check the contents of
this package to ensure that all necessary components are included. Please contact us immediately via email if any
parts appear to be missing.
Please ensure that you assemble the goods in a clean, dry area, with plenty of space, and that you have the correct
tools and equipment to hand. We recommend that you read the instructions in full before you commence assembly,
and if necessary, run through the installation procedure without physically assembling any items before you begin.
Only construct one cabinet at a time, and follow the installation stages in order, without modication. During
installation, be careful to keep the relevant ttings for the current cabinet together. Do not over tighten screws, and
ensure that any larger panels are laid at and protected.
We advise using a damp cloth and – if necessary – a small amount of liquid soap to clean the cabinet. Do not use
abrasive materials. For more information, please view the full cleaning and aftercare guide on our website
SC-IFU-308-SL-D450-W300-600

1
1
12 x
3 x
1 x
1 x
1 x
2
3
4
5
2
3
4
5
4 x H
4 x I
2 x J
12 x
24 x
12 x
A
B
C
4 x D
E
4 x
2 x
F
G
12 x
15mm
25mm
Panels
Hardware

1
A
A
A
A
E
E
E
E
2
B
B
2
B
B
1
2
A E
E
Insert and as shown in the diagram
below.
Apply a small drop of
glue to each dowel
before inserting.
B
Insert as shown ensuring the arrow
marking is pointing towards the outside edge.
2
B
B
AE
AE
3
B
B
B
B
B
B

1
1
3
2
3
4B
Connect the base panel to the side panel
using the ttings inserted during steps 1 and 2.
Repeat the process for all
top panels
Connect the opposite side panel as shown then tighten all
ttings by turning in direction of arrow with screwdriver.
1
2
2
3
2
1
1
2
2
3
2
B

1
2
3
4
5Slide the back panel between the grooves on the
inside edge of each side panel as shown.
It is advised that you run a small amount of glue along
the grooves rst.
4
1

Position each foot mount towards
the edge of the base panel at each
corner. Ensure screw holes are not
aligned over the panel join and that
the overhang foot support is
overlapping the side panel as shown
below.
Drill 3mm pilot holes into the
base panel through the four
mounting holes in each foot
mount. Now screw the four
screws supplied with each foot
directly through the foot mount
and into the base panel.
Attach the adjustable legs to
each foot mount and adjust to the
appropriate height.
1
23
Fitting Cabinet Legs
H
I
30mm
C

Hinge
Holes
Join
Hole
Joining Cabinets
Cabinets should be joined be-
tween each set of hinge holes
on the inside edge of the side
panel as shown in the diagram.
Mark 25mm as a guide on a
3mm diameter drill bit using
masking tape. Drill between
the hinge holes into the cabi-
net side panel (18mm) and
7mm into the next until you
reach the marker. Join the two
cabinets together using the
25mm screws provided D
Fitting Cabinet to Wall
When xing the cabinet to the wall you must only use slotted angle
brackets . A round head screw must be used to x the bracket.
It is important that you use the slot that runs at perpendicular to the width
(across and not parallel with the grain).
G
Wall
Top panel
Side Panel

Clip each plinth clip onto
the legs at the front
Plinths
Secure plinth to plinth clip using
screw provided C
J
I
of the cabinet.
Fitting Shelves and Plinths
Push the shelf supports into the
pre-drilled shelf holes then sit the shelf
on top.
Shelves
F