Solid Wood Kitchen Cabinets Wide Sink Cabinet User manual

Assembly Guide
800mm — 1200mm Wide Sink Cabinet
IMPORTANT – Please read prior to installaon
Thanks for purchasing a solid oak kitchen cabinet. Prior to commencing installaon please
check the contents of this package to ensure that all necessary components are included.
Please contact us immediately via email if any parts appear to be missing.
Please ensure that you assemble the goods in a clean, dry area, with plenty of space, and
that you have the correct tools and equipment to hand. We recommend that you read the
instrucons in full before commencing assembly; and if unsure we advise an inial rehears-
al of the installaon procedure without physically assembling any items. Only construct
one cabinet at a me and follow the installaon stages in order without modicaon. Dur-
ing installaon, be careful to keep the relevant ngs for each cabinet together. Do not
over-ghten screws, and ensure that any larger panels are laid at and protected.
We advise using a damp cloth and – if necessary – a small amount of liquid soap to clean
the cabinet. Do not use abrasive materials. For more informaon, please view the full
cleaning and aercare guide on our website.
SC-IFU-330-SP-SI-W800-1200

Panels
Hardware
SC-IFU-330-SP-SI-W800-1200
1 x
2 x
2 x
1 x
1
2
3
4
1
2
3
4
1
3
5
1 x 5
10 x
10 x
28 x
4 x
14 x
4 x
2 x
5 x
5 x
2 x

2
SC-IFU-330-SP-SI-W800-1200
Insert cams B into the panels and as
shown in the diagram below. Ensure that the ar-
row marking is poinng towards the outside edge
of the panel.
B 23
3
2
B B
B B
3
B
1
Insert connecng bolts and dowels as
shown in the diagram below for both side pan-
els . Apply a small drop of glue to each
dowel before inserng.
1A E
A
A
A
E
E
E
A
E
11
A
A
E
A
A
E
A
EA

2
3
3
1
2
1
SC-IFU-330-SP-SI-W800-1200
3Connect the base panel to the side
panel using the ngs inserted during
steps 1 and 2. Repeat the process for all
top panels
2
1
3
4
3
D
3
4Fit support panel using 4x dowels and
secure with 2x screws .
4E
D
D

2
1
SC-IFU-330-SP-SI-W800-1200
5Connect the opposite side panel as shown
in the diagram below. Tighten all the ngs
by turning them in the direcon of the arrow
with a screwdriver.
1
B
1
3

Fing Cabinet Legs
1
Posion each leg housing towards
the edge of the base panel at each corner.
Ensure screw holes are not aligned over
the panel join and that the overhang foot
support is overlapping the side panel as
shown in the diagram below.
H
Drill 3mm pilot holes into
the base panel through the
four mounng holes in
each leg housing. Now
screw the four screws
supplied with each leg di-
rectly through the leg
housing and into the base
panel.
C
2
Aach the adjustable
legs to each leg
housing and adjust to
the appropriate height.
I
3
SC-IFU-330-SP-SI-W800-1200

SC-IFU-330-SP-SI-W800-1200
Cabinets should be joined
between each set of hinge
holes on the inside edge of
the side panel as shown in
the diagram. Mark 25mm as
a guide on a 3mm diameter
drill bit using masking tape.
Drill between the hinge
holes into the cabinet side
panel (18mm) and 7mm in-
to the next unl you reach
the marker. Join the two
cabinets together using the
25mm screws provided.
D
When xing the cabinet to the wall you must only use
sloed angle brackets . A round head screw must
be used to x the bracket. It is important that you use
the slot that runs at perpendicular to the width (across
and not parallel with the grain).
G
Joining Cabinets
Fing Cabinet to Wall

Fing Shelves and Plinths
SC-IFU-330-SP-SI-W800-1200
Secure plinth to plinth holder clip using
screw provided.
J
C
Clip each plinth clip
onto the legs at
the front of the
cabinet.
I
Shelves
Push the shelf supports
into the pre-drilled shelf
holes then sit the shelf on
top.
F
Plinths