Sollae Systems CIE-H10 User manual

Sollae Systems Co., Ltd.
http://www.sollae.co.kr
I/O Device Server
CIE-H10 User's Manual
Version 2.0
2009-06-22

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 1 - http://www.sollae.co.kr
To all residents of the European Union
Important environmental information about this product
This symbol on this unit or the package indicates that disposal of this unit after its
lifecycle could harm the environment. Do not dispose of the unit as unsorted
municipal waste; it should be brought to a specialized company for recycling. It is your
responsibility to return this unit to your local recycling service. Respect your local
environmental regulation. If in doubt, contact your local waste disposal authorities.

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 2 - http://www.sollae.co.kr
Contents
CONTENTS ........................................................................................................................................... - 2 -
1 INTRODUCTION ...................................................................................................................... - 5 -
1.1 Introduction .......................................................................................................................................................... - 5 -
2 SPECIFICATION ....................................................................................................................... - 6 -
2.1 Components ......................................................................................................................................................... - 6 -
2.2 Product Specification ....................................................................................................................................... - 6 -
2.3 Interface.................................................................................................................................................................. - 7 -
2.3.1 Input Port .................................................................................................................................................. - 7 -
2.3.2 Output Port .............................................................................................................................................. - 8 -
2.3.3 RS232 Port (DB9M) ............................................................................................................................... - 9 -
2.3.4 Ethernet Interface ............................................................................................................................... - 10 -
2.3.5 Power ........................................................................................................................................................ - 10 -
2.3.6 System LED ............................................................................................................................................ - 10 -
2.3.7 ISP Switch ............................................................................................................................................... - 11 -
3 TEST........................................................................................................................................ - 12 -
3.1 Installation .......................................................................................................................................................... - 12 -
3.1.1 Confirming Environment ................................................................................................................. - 12 -
3.1.2 Network Connection ......................................................................................................................... - 12 -
3.1.3 Setting parameters ............................................................................................................................. - 12 -
3.1.4 Test Operation ..................................................................................................................................... - 12 -
3.2 Test operation .................................................................................................................................................. - 13 -
3.2.1 Changing the IP address of PC .................................................................................................... - 13 -
3.2.2 Installing CIE-H10 ............................................................................................................................... - 13 -
3.2.3 Configuring CIE-H10 ......................................................................................................................... - 13 -
3.2.4 Modbus/TCP Test ............................................................................................................................... - 15 -
3.2.5 Testing on Web Browser (HTTP) ................................................................................................. - 16 -
4 IP ADDRESS AND SETTING VALUES ................................................................................ - 17 -
4.1 IP address and setting values ................................................................................................................... - 17 -
4.2 Settings by ezManager ................................................................................................................................ - 17 -
4.2.1 ezManager ............................................................................................................................................. - 17 -
4.2.2 Buttons of ezManager ...................................................................................................................... - 18 -
4.2.3 ezManager Settings ........................................................................................................................... - 18 -
4.2.4 Matters to be attended to ............................................................................................................. - 19 -

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 3 - http://www.sollae.co.kr
4.3 IP Address Related Categories Settings via DHCP ......................................................................... - 19 -
4.4 IP Address settings via PPPoE .................................................................................................................. - 19 -
4.5 Notify IP Change (DDNS) ............................................................................................................................ - 20 -
5 I/O INTERFACE ..................................................................................................................... - 21 -
5.1 Modbus/TCP...................................................................................................................................................... - 21 -
5.1.1 Modbus/TCP Setting Values .......................................................................................................... - 22 -
5.1.2 Standard Modbus/TCP ..................................................................................................................... - 23 -
5.1.3 Modbus/TCP Master Mode............................................................................................................ - 23 -
5.1.4 TCP Connection Mode ..................................................................................................................... - 24 -
5.1.5 Initial Output Value ........................................................................................................................... - 24 -
5.2 Macro Mode...................................................................................................................................................... - 24 -
5.2.1 Operator .................................................................................................................................................. - 24 -
5.2.2 Operand .................................................................................................................................................. - 25 -
5.2.3 Example of Equations ....................................................................................................................... - 25 -
5.3 Monitoring and controlling on Web (HTTP) ...................................................................................... - 25 -
5.3.1 Connect to Web .................................................................................................................................. - 26 -
5.3.2 Change the port number of web server .................................................................................. - 26 -
5.3.3 Using User’s Web Pages ................................................................................................................. - 27 -
5.4 Serialized Modbus/TCP ................................................................................................................................ - 27 -
6 SERIAL INTERFACE .............................................................................................................. - 28 -
6.1 Serial communication mode ...................................................................................................................... - 28 -
6.2 T2S – TCP Server ............................................................................................................................................. - 29 -
6.2.1 Connection ............................................................................................................................................. - 29 -
6.2.2 Serial Data before the TCP connection .................................................................................... - 29 -
6.2.3 Data Communication ........................................................................................................................ - 29 -
6.2.4 Connection Termination .................................................................................................................. - 30 -
6.3 COD – TCP Client ............................................................................................................................................ - 31 -
6.3.1 Serial Data before Connection ..................................................................................................... - 31 -
6.3.2 Data Communication ........................................................................................................................ - 31 -
6.3.3 Connection Termination .................................................................................................................. - 32 -
6.3.4 DNS ........................................................................................................................................................... - 32 -
6.4 ATC ........................................................................................................................................................................ - 33 -
6.5 U2S – UDP.......................................................................................................................................................... - 34 -
7 CHECKING AND DEBUGGING ........................................................................................... - 35 -
7.1 Telnet .................................................................................................................................................................... - 35 -
7.1.1 Telnet Login ........................................................................................................................................... - 35 -
7.1.2 Commands ............................................................................................................................................. - 35 -

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 4 - http://www.sollae.co.kr
7.2 Status of ezManger ........................................................................................................................................ - 37 -
7.3 Debugging Message ..................................................................................................................................... - 38 -
8 SECURITY OPTIONS ............................................................................................................ - 39 -
8.1 Password ............................................................................................................................................................. - 39 -
8.1.1 Set and Delete Password ................................................................................................................ - 39 -
8.1.2 CIE-H10 settings with Designated Password ......................................................................... - 39 -
8.1.3 Connect via Web Browser .............................................................................................................. - 40 -
8.1.4 When Password is Lost .................................................................................................................... - 40 -
8.2 Connection Restriction Function ............................................................................................................. - 40 -
8.2.1 Allowed MAC Address ...................................................................................................................... - 40 -
8.2.2 Allowed IP Address ............................................................................................................................ - 41 -
8.2.3 Apply To ezManager ......................................................................................................................... - 41 -
8.2.4 Solving the problem with ezTCP Firewall ................................................................................ - 41 -
9 TECHNICAL SUPPORT/WARRANTY /PRECAUTIONS .................................................... - 42 -
9.1 Technical Support ........................................................................................................................................... - 42 -
9.2 Warranty .............................................................................................................................................................. - 42 -
9.2.1 Refund ...................................................................................................................................................... - 42 -
9.2.2 Free A/S ................................................................................................................................................... - 42 -
9.2.3 Charged A/S .......................................................................................................................................... - 42 -
9.3 Precautions ........................................................................................................................................................ - 42 -
10 ORDERING INFORMATION ................................................................................................ - 43 -
11 REVISION HISTORY ............................................................................................................. - 44 -

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 5 - http://www.sollae.co.kr
1 Introduction
1.1 Introduction
The need for the data communication system via Internet is rapidly increasing due to the
development of Internet throughout the world. In order to send and receive data via
Internet, TCP/IP protocol must be used. Any machines that need an Internet connection
must implement TCP/IP protocol. In order for any device to implement TCP/IP protocol, the
machine must either be able to implement TCP/IP protocol by itself, have an open TCP/IP
source implanted, or must use an OS that is capable of implementing the protocol.
However, the above options require a great deal of time, cost and effort to make it work.
CIE-H10 uses Modbus/TCP and HTTP to provide users with ability to control and monitor
remote digital I/O controllers. Therefore, with CIE-H10, remote I/O devices can easily be
controlled and monitored at the same time. Also, CIE-H10 provides the Macro functions to
automatically change the output port value based on the value of input port.
Not only that CIE-H10 can control and monitor digital I/O controllers, it also provides
with functions that can covert the serial data to TCP/IP data and vice versa. Therefore, one
CIE-H10 can perform numerous functions at the same time.
Along with its strong TCP/IP/UDP functions, CIE-H10 also provides DHCP and PPPoE
functions to be used in cable and xDSL networks. And it has DDNS (Dynamic DNS) function,
so it can be used more easily in the internet.
It is also equipped with online debugging functions that will allow the users to quickly
respond to the problems that might occur during the installation.

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 6 - http://www.sollae.co.kr
2 Specification
2.1 Components
Name Comment
CIE-H10 body -
5V Power Adapter -
RS232C Cable for PC Option
Adapter for DIN rail Option
2.2 Product Specification
Power
Input Power 5V (±10%)
Current
Consumption
510mA typical
Size 153mm x 126mm x 32mm
Weight Approximately 530g
Interface
Input Port 8 Port Photo coupler
Output
Port 8 Port Relay
Serial Dsub 9Pin male
Network 10Base-T/100Base-TX (RJ45)
Network Ethernet 10/100 Mbits auto-sense
Auto MDI/MDIX(Cable Auto-sensing)
Protocol
TCP, UDP, IP, ICMP, ARP, DHCP, PPPoE, DNS lookup,
Dynamic DNS(DDNS), Telnet COM Port Control Option(RFC2217)
Modbus/TCP, HTTP
Diagnose Online Debugging Function
Environment Follows Europe RoHS Directive
Certification CE: F690501/SP-EMC000976
Communicat
ion Mode
Input/Output
Port
Modbus/TCP – Slave/Master, Passive/Active
Web Browser(HTTP)
Macro(Stand alone)
Serial Port TCP Server/Client, AT emulation, UDP
Programs
ezManager Configuration program via LAN
ezTerm Socket communication program for testing
hotflash Firmware download program using TFTP

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 7 - http://www.sollae.co.kr
2.3 Interface
2.3.1 Input Port
Since CIE-H10 input port is isolated by photo-couplers, users may connect the machine
regardless of its polarity. The circuit of the input port is shown in the below. It is the part
where the [EXTERNAL INPUT1] and [EXTERNAL INPUT2] are interfaced with the user device.
The specifications of the input port are as the following:
Max. Input Voltage DC24V
V
IH
Min. 1.8V H 1
V
IL
Max. 1.2V L 0
Since the input port is interfaced with a 5mm terminal block, use a (-) shaped screwdriver
to connect it with the user device.
Valid Time
CIE-H10 will only recognize input port signals that last for the [Valid Time] set by the
user. If the signal is not maintained during the designated [Valid Time], the input signal will
be ignored.
The [Valid Time] is used for Modbus/TCP, Macro, HTTP and other functions provided by
CIE-H10. The unit used for the [Valid Time] is 1ms. However, since the accuracy is only
guaranteed in 10ms, the designated values will round down in units of 10ms according to
the designated values by the users.
Input Port Type
Basically, input ports of CIE-H10 are Open Collector type. The type needs two wires
which have difference of voltage level for making HIGH signal. However, the accessory
which let the input ports can be used as Dry Contact type will be introduced soon. By
10K
1K(1/4W)
3.3V
TO PROCESSOR
1K(1/4W)
EXTERNAL INPUT 2
EXTERNAL INPUT 1

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 8 - http://www.sollae.co.kr
using the accessory, you can input HIGH signal with switch (relay) interface.
2.3.2 Output Port
CIE-H10 output port is interfaced via relay as shown below. It is the part where the
[EXTERNAL OUTPUT1] and [EXTERNAL OUTPUT2] are interfaced with the user device.
The output port will perform the following actions
Value Relay contact
0 OFF
1 ON
The allowed electrical current based on voltage conditions of the output port are as the
following:
Voltage Condition Allowed current
DC28V 5A
AC125V 10A
AC250V 5A
Despite the relay have the capacity to "switch" 5 A (AC250V), the CIE-H10 have been
design to switch lower voltage and that it is better to use external additional relay to
switch main 220 V
Since the output port is interfaced with a 5mm terminal block, use a (-) shaped
screwdriver to connect it with the user device.
Delay
CIE-H10 will send output value to the output port after waiting for [Delay].
In order to do so, the signal value must last for [Delay] seconds. If the output value does
not last for the [Delay] seconds, CIE-H10 will not send that signal to the output port.
If the [Delay] value is set as 0, CIE-H10 will send the output value to the output port
immediately.
The [Delay] is used for Modbus/TCP, Macro, HTTP, and other functions provided by CIE-
RELAY SPST
23
1
5
EXTERNAL OUTPUT1
VCC_5V
FROM_PROCESSOR
EXTERNAL OUTPUT2

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 9 - http://www.sollae.co.kr
H10. The unit used for the [Delay] is 1ms. However, since the accuracy is only guaranteed
in 10ms, the designated values will round down in units of 10ms according to the
designated values by the users.
2.3.3 RS232 Port (DB9M)
CIE-H10 has an RS232 port for user serial device (300bps ~ 230,400bps). CIE-H10
converts serial data from user device to TCP/IP and transmits to Ethernet port. And CIE-H10
convert TCP/IP data from Ethernet port to user serial device and it transmits raw data to
user device.
Pin Assignment
number name description level Dir. Etc.
1 DCD Data Carrier Detect RS232 Input option
2 RXD Receive Data RS232 Input required
3 TXD Transmit Data RS232 Output required
4 DTR Data Terminal Ready RS232 Output option
5 GND Ground Ground - required
6 DSR Data Set Ready RS232 Input option
7 RTS Request To Send RS232 Output option
8 CTS Clear To Send RS232 Input option
9 RI Ring Indicator RS232 Input option
Data bits, Parity, and Stop bit
Item Configurable Value
Data bits 8, 7, 6, 5
Parity None, Even, Odd, Mark, Space
Stop bit 1, 1.5, 2
Flow Control
CIE-H10 supports RTS/CTS Hardware Flow Control.
Telnet COM Port Control Option
CIE-H10 has Telnet COM Port Control Option function that is specified by RFC2217. If the
Telnet COM Port Control Option is enabled, CIE-H10 sends the CTS, DSR control signal to
the communication counterpart, and CIE-H10 sets its serial port items (RTS, DTR, Baud rate,
data bits, parity, stop bit) after getting information from the communication counterpart.

CIE-H10 User's Manual
Ver.
Sollae Systems Co., Ltd.
2.3.4
Ethernet Interface
Since part of CIE-
H10 network is composed of Ethernet, UTP cable may be
will automatically sense 10Mbit
auto MDI/MDIX function that can automatically sense 1:1 cable or cross over cable.
Each Ethernet device has its own unique hardware address. The hardware address of CIE
H10 is set in the factory before being shipped to the market
known as the MAC address)
2.3.5 Power
DC5V is used for the power.
2.3.6 System LED
CIE-H10 has several
lamps to show the current system status.
Each lamp shows the following st
Mode
Name
Common
Normal
mode
Ver.
2.0
- 10 -
Ethernet Interface
H10 network is composed of Ethernet, UTP cable may be
will automatically sense 10Mbit
s or 100Mbits
Ethernet and connect itself
auto MDI/MDIX function that can automatically sense 1:1 cable or cross over cable.
Each Ethernet device has its own unique hardware address. The hardware address of CIE
H10 is set in the factory before being shipped to the market
. (The
hardware address is also
known as the MAC address)
DC5V is used for the power.
The specifications of the power jack
are as the following:
lamps to show the current system status.
Each lamp shows the following st
atus:
Name
Color LED 상태
PWR Red On
Supplying the p
LINK
Green On
Connecting with
Red On
Connecting with
RXD Yellow Blinks
Receiving data from the
TXD Green Blinks
Sending data to the
STS Yellow
Blinks in every
second Being
assigned
Blinks 4 times
IP address is not assigned in
http://www.sollae.co.kr
H10 network is composed of Ethernet, UTP cable may be
connected. It
Ethernet and connect itself
. It also provides
auto MDI/MDIX function that can automatically sense 1:1 cable or cross over cable.
Each Ethernet device has its own unique hardware address. The hardware address of CIE
-
hardware address is also
are as the following:
설명
Supplying the p
ower
Connecting with
100M bit
network
Connecting with
10M bit
network
Receiving data from the
Ethernet
Sending data to the
Ethernet
assigned
IP address
IP address is not assigned in

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 11 - http://www.sollae.co.kr
in every second DHCP or PPPoE mode
On Establishing Modbus/TCP
connection
DI Yellow On Input ON(High) signal to
input port
DO Green On Output ON signal from
output port relay
Serial
Configuration
mode
LINK,STS,
RXD,TXD
- Blinks
simultaneously
Entering serial configuration
mode
ISP mode STS Yellow Off Entering ISP mode
2.3.7 ISP Switch
There is an ISP switch located on the side of the product. It is a switch that will allow
CIE-H10 to be operated as serial configuration mode or ISP mode. If the switch is pressed
between 20ms and 1s, CIE-H10 will enter the serial configuration mode. In this mode, you
can configure the environment parameters through the RS232 port.
If the button is pressed over a second or the power is supplied when you are pressing
the button, CIE-H10 will be operated as ISP mode.
Both modes let the security options like password be restored. Use this mode when
faced with the problems.

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 12 - http://www.sollae.co.kr
3 Test
3.1 Installation
CIE-H10 can be installed with the following procedure.
Large category Small category Details
1. Confirming Environment
Confirm
categories
IP address environment
Modbus/TCP, HTTP, Macro
Serial port value
Application program
2. Network Connection Confirm
method Check for LINK LED light
3. Setting parameters Setup Method Network Setup utility, ezManager
4. Test Operation Confirm
method
Check with ezManager or Web
browser(HTTP)
5. Applying to the system - -
3.1.1 Confirming Environment
Check the IP address, network environment, the serial port values, protocols used in
controlling digital I/O devices and other application programs before installing CIE-H10.
3.1.2 Network Connection
After connecting CIE-H10 to the power, directly connect it with PC’s Ethernet port or
connect it to the network (hub) that the PC is also connected with. When the LINK LED is
on, the network is established.
However, since CIE-H10 is only physically connected, IP related values must be
designated to perform ping test and IP communication.
3.1.3 Setting parameters
When network connection is established, ezManager program can be used to perform
setup all the environment values via LAN.
3.1.4 Test Operation
The test operation can be performed with the test program on ezManager or web
browser. For more details about this, please refer to 3.2 test operation.

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 13 - http://www.sollae.co.kr
3.2 Test operation
The test operation may be performed according to the following procedure. The test
operation suggested in this manual is based on the assumption that IP of PC is set as
10.1.0.2.
3.2.1 Changing the IP address of PC
Change IP address of PC as the following:
IP address 10.1.0.2
Sub net mask 255.0.0.0
Gateway IP address -
3.2.2 Installing CIE-H10
Connect LAN cable directly to the LAN port of CIE-H10 or connect it to the hub where
the PC is connected with. Also, provide power to CIE-H10 using the power adapter. When
the power is supplied, the LINK LED will light up when a proper connection to the LAN
cable is established.
3.2.3 Configuring CIE-H10
Using ezManager, change the settings of CIE-H10. Start ezManager and click [Search All]
button on the ezManager window. Then, ezManager will search for every ezTCP on the
local network.
When there is no result, click [Windows Firewall] button window to check for firewall
setting. If this setting is ON, the ezManager cannot perform the search.
When CIE-H10 is found, the MAC address of CIE-H10 will be shown on the [Search
Results] window. (The MAC address is also written on the bottom of the product case.)
Select the MAC address and set its values properly. For this test, we recommend that
keeping the default values configured in the factory like below table.

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 14 - http://www.sollae.co.kr
Parameter Value
Network Local IP Address 10.1.0.1
Subnet Mask 255.0.0.0
Option Telnet Enabled
IP Address Search Enabled
Serial Port
Serial Type RS232
Baud Rate 19200bps
Parity NONE
Data Bits 8
Stop Bit 1
Flow NONE
Communication Mode T2S – TCP Server
Local Port 1470
I/O Port
Web (HTTP) Enabled
Web (HTTP) Port 80
Modbus/TCP Enabled
Master/Slave Slave
Connection Mode Passive Connection
Peer Port 502

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 15 - http://www.sollae.co.kr
3.2.4 Modbus/TCP Test
It is a test of CIE-H10 to perform control and monitor functions using Modbus/TCP. This
test should be performed with Modbus/TCP program provided by Sollae Systems.
After having settings as same as the settings shown above, click on the [CIE-H10 TEST]
button. A new window on the ezManager will pop up.
 Click [Connect] button to connect to CIE-H10 by TCP connection
In order to check for the Output ports, click the Do0 to Do7 buttons of the [I/O
Port] panel to check for output values being sent.
When the [Start] button in the [Write] panel is clicked, previously designated values
will be sent to the [Digital Output] port periodically.
In order to check for the Input ports, click [Start] button in the [Read] part. The
program will read and indicate the value of each Input port in every period designated
by the [Poll Interval] box.

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 16 - http://www.sollae.co.kr
3.2.5 Testing on Web Browser (HTTP)
Start the web browser as shown below and write http:// and IP address in the address
window to connect to the CIE-H10 web browser. It will allow users to monitor and control
their CIE-H10 remotely.
Click on the [Read] button to read input/output values.
Designate output values on the CIE-H10’s output ports (DO0 – DO7) and click [Write]
button to apply setting values to the CIE-H10’s output port. Then, the CIE-H10’s input port
value will be read as well.

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 17 - http://www.sollae.co.kr
4 IP Address and Setting Values
4.1 IP address and setting values
In order to perform TCP/IP communication, the settings related to the IP address must
be designated. Including the IP addresses and serial port parameters, all the environment
values can be set by ezManager, the utility provided by Sollae Systems.
4.2 Settings by ezManager
4.2.1 ezManager
The basic settings of CIE-H10 (IP address, serial port and etc) can be designated by an
application utility for Windows, ezManager. ezManager can be operated in Windows
platform (Windows 98, 98SE, 2000, ME, XP, Vista) but may malfunction in older OS versions.
The following window is the window that pops up when the user starts ezManager for the
first time.
ezManager communicates with CIE-H10 via UDP broadcast. The port used during the
communication is 50005 and the UDP port used during the debugging process is 50006. If
the firewall functions are being used, the firewall functions for the 50005 and 50006 ports
must be turned off.

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 18 - http://www.sollae.co.kr
4.2.2 Buttons of ezManager
Search All Search for all the ezTCP connected to the local network.
Read Read the values configured through MAC or IP address.
Write Store the changed values of parameters
Set Password Set or remove the password by this button.
Status Check the status of ezTCP in real time.
Factory Reset Initialize all the values as a default.
Debugging Message Make the ezTCP broadcast debugging messages.
Change F/W / HTML Change the firmware or HTML files with this button.
Export Variables Store a set of values as a file.
Import Variables Load values from a file made from [Export Variables]
Multi Write Configure a set of values to one or more ezTCP
PING/ARP Test the PING reply and manage the ARP table.
Simple Test Run the test program interfaced with Network and RS232 port.
Windows Firewall Run the windows firewall set window.
Exit Exit ezManager
4.2.3 ezManager Settings
Tap Section Parameter
Network
Network Local IP Address, Subnet Mask,
Gateway IP, DNS IP Address
Notify IP
Change
Protocol, Interval, Port, Data Type, DDNS ID,
DDNS Password, Host Name(dyndns/custom)
Option
Obtain an IP From The First Received Packet,
Obtain an IP Automatically (DHCP),
Obtain an IP Automatically (PPPoE),
PPPoE ID, PPPoE Password,
Obtain DNS Server Address Automatically
Option
Option
Telnet, IP Address Search, Send MAC Address,
Debugging Message, SSL, SSH,
Multiple Connection
ezTCP Firewall
Allowed MAC Address, Allowed IP Range,
IP Address, Network Mask,
Apply To ezManager

CIE-H10 User's Manual Ver. 2.0
Sollae Systems Co., Ltd. - 19 - http://www.sollae.co.kr
Serial Port
Serial Port Serial Type, TTL, Baud Rate, Parity, Data Bits,
Stop Bit, Flow Control, DTR/DSR, TX Interval
TCP/IP
Communication Mode, Peer Address,
Peer Port, Local Port, Event Byte, Timeout,
Data Frame
I/O
Port
Basic
Settings
Web(HTTP) Web(HTTP), Web Port, Size of Web
Modbus/TCP
Modbus/TCP, Notify Input Port Change,
Master/Slave, Poll Interval, Unit ID,
Input Port Base Address,
Output Port Base Address,
Active/Passive Connection,
Peer Address, Peer Port
I/O Port
Option
Digital Input Valid Time
Digital Output Macro, Delay, Initial State
I/O Port
Comment
Digital Input Comment
Digital Output Comment
4.2.4 Matters to be attended to
ezManager can be used when you want to change your device’s environment variables.
In case of CIE-H10, two interfaces are supported and those are Ethernet and RS232 port.
Using Ethernet Port
For use ezManager through Ethernet, CIE-H10 should be connected with PC on networks.
If they are located at the same network, [Search All], on the [MAC] tap, could be used with
MAC address. If they are connected on Internet, [Read], on the [IP] tap, could be used.
Using RS232 Port
For use ezManager through RS232, not only the CIE-H10 should be connected to PC with
RS232 cross cable but also has to be operated as serial configuration mode.
4.3 IP Address Related Categories Settings via DHCP
In the network environment composing DHCP server, settings related to CIE-H10’s IP
address, subnet mask, gateway, and name servers can be automatically designated using
DHCP protocol. In order to do so, user must check [Obtain an IP Automatically (DHCP)]
category on ezManager. Depending on DHCP server type, [Obtain an IP from the First
Received Packet] category should also be checked as well.
4.4 IP Address settings via PPPoE
Usually, PPPoE is used in ADSL or VDSL environment. In order to use PPPoE, PPPoE
function must be activated and PPPoE ID and password must be designated accordingly.