Solution Ozone SSO-O3-SPA01 User manual

SSO-O3-SPA01
SPA O3 System
User Manual
Ver: 2.01
Cered by:

Ozone
1 - Ozone is an extremely powerful oxidizing agent, capable of eecvely oxidizing
bacteria, fungi, microorganisms and viruses.
2 - Ozone is 1,5 mes stronger than chlorine and 3 125 mes faster in inacvang bacteria
and viruses.
3 - Ozone does not change the pH or the alkalinity of the water.
4 - Ozone is 100% natural and aer its acon it is returned to nature in the form of
oxygen.
Applicaon
1 - Eliminates harmful elements from water - Ozone is an oxidizing agent capable of
eecvely oxidizing more than 99% of bacteria, algae, fungi, microorganisms, protozoa
and viruses.
2 - Does not produce toxins avoiding the formaon of organic by-products - Ozone
promotes the oxidaon of organic and non-organic parcles without the formaon of
undesirable by-products, such as chloramines (generated from the reacon of chlorine
with impuries present in water such as tanning, makeup , body creams, urine, sweat and
other secreons).
3 - Removes obsolete odors and smells - Ozone is a powerful oxidizing agent that allows
oxidizing harmful toxic elements and organic odors in water, removing bad smells and
reducing their toxicity without any secondary polluon.
4 - Reduces water consumpon - Ozone improves water quality, keeping it clean and
crystalline for longer, reducing water seedlings.
5 - Does not cause irritaon - The use of ozone in the treatment of SPAs reduces the
risk of skin and eye irritaon, allergies, respiratory problems, ear infecons, and dehydra-
on of the skin and hair that normally occurs with the use of chlorine.
6 - Does not damage bathing suits - The use of ozone does not harm bathing suits
(discoloraon and fragility of the elascs.
Specicaons
2
..EN
SSO-O3-SPA01 - User Manual (EN)
Model SSO-O3-SPA01
Ozone Output 100mg/h
Gas Supply Ambient Air
Water Volume ≤ 10 m3
Fuse 100 mA
Rated Power ≤ 12W
Voltage 240 V AC
Size (LxWxD) mm 200 x 110 x 65
Weight (kg) 0,60
Table 1— Specicaons
Copyright @ 2020 Ozone Soluon. All rights reserved. This document accompanies the O3 System for SPAs. This document is subject to review.
Merely illustrave images.
Ver2/01-Ver.02

3
Equipment Structure:
Included:
 1 Ozone Generator SSO-O3-SPA01
 1 Silicone Tube
 1 Check Valve
 1 Venturi ½”
 User Manual
 Wall-mouted screws
Installaon and Operaon Instrucons
1.1 - Remove the equipment and the silicone tube from the box.
1.2 - Turn o power to SPA. Be sure the electrical power is shut OFF at the main circuit
breaker before installing the SSO-O3-SPA01.
1.3 - Find the ozone generator installaon ng, on the wall of the equipment
compartment. Install the SSO-O3-SPA01 at the ozone generator installaon ng, use the
mounng screws and fasten the unit to the wall.
Note: Be cauons of the mounng locaon as to not cause the screws to penetrate any
plumbing. The SSO-O3-SPA01 must be mounted indoors or sheltered, under a cover, from
natural elements (rain, sun, ...). Mount the SSO-O3-SPA01 so that is inaccessible to anyone
in the SPA.
1.4 - The SSO-O3-SPA01 must be installed horizontally, with the front image on the right
posion and the Ozone Outlet turned to the le/down side (see image 2). Use both
mounng anges and install the equipment as high as possible with the protected
equipment area.
1.5 - Plumbing - for an opmal dissoluon of ozone into the SPA Water, install the SSO-O3-
SPA01 mixing system in the Water circulaon lina as shown in Image 2:
1.5.1 - Connect the addional silicone tube (supplied with the Ozone Generator) to the
check valve on the SSO-O3-SPA01.
..EN
SSO-O3-SPA01 - User Manual (EN)
Copyright @ 2020 Ozone Soluon. All rights reserved. This document accompanies the O3 System for SPAs. This document is subject to review.
Merely illustrave images.
Ver2/01-Ver.02
Image 1 - Equipment Structure
Power Cable
Ozone Generator
Check Valve
Fuse
Ozone Outlet

4
1.5.2 - Run tubing to the venturi (supplied with the Ozone Generator) or to an
appropriate vacuum source.
1.5.2.1 - If the ozone generator is installed above the SPA Water Line, tubing may be
run directly to the venturi or to an appropriate vacuum source.
1.5.2.2 - If the ozone generator is installed below the SPA Water Line, run tubing to a
point above the water line and back down (loop) to the venturi/vacuum source.
1.5.3 - Secure all tubing connecons with hose clamps.
Note: For circulaon systems dierent from the one shown in image 2, contact your
SPA supplier for proper plug conguraon.
1.6 - Electrical installaon (see image 3):
1.6.1 - Verify there is no power to the SPA and connect the SSO-O3-SPA01 power cord
into the mang connector(s) on the SPA Control Box.
1.6.2 - Where possible, route the SSO-O3-SPA01 power cord away from other electrical
lines. Avoid roung the power cord parallel to any low-voltage signal wires.
..EN
SSO-O3-SPA01 - User Manual (EN)
Image 2 - Installaon
Copyright @ 2020 Ozone Soluon. All rights reserved. This document accompanies the O3 System for SPAs. This document is subject to review.
Merely illustrave images.
Ver2/01-Ver.02
WARNING:
To reduce the risk of electrical shock, if the power cord is damaged, replace the
enre unit immediately.

5
..EN
SSO-O3-SPA01 - User Manual (EN)
1.7 - Operaon:
1.7.1 - With the SPA lled to the proper level, run the SPA Controller through several
cycles.
1.7.2 - Check for and correct any leaks in the ozone tubing.
1.7.3 - Check that the Ozone Generator is working properly. Note that bubbles are being
placed into the SPA via heater return and you will noce a faint scent that resembles a
rain storm.
WARNING:
Do not breathe ozone directly. If there is any leakage of ozone in the system, turn it o
immediately and leave the space and only return aer 30 minutes (so that all the ozone in
the air is completely dissipated). According to OSHA standards, you should not be exposed
for more than 0.1 ppm for periods of 8 hours / day.
Image 3 - Electrical Diagram
WARNING:
The Ozone Generator works at high voltage and should only be opened by Soluon Ozone®
Technicians. Before carrying out any work on the Pool Circulaon System, make sure that
the electrical supply to the Ozone Generator is turned o.
Copyright @ 2020 Ozone Soluon. All rights reserved. This document accompanies the O3 System for SPAs. This document is subject to review.
Merely illustrave images.
Ver2/01-Ver.02

6
Maintenance
2.1 - To ensure the proper funconing of the system, it is recommended to carry out periodic
maintenance on the Ozone Generator.
2.2 - Regularly inspect ozone supply tubing for cracks or wear. Make sure that is no water
present between the check valve and ozone generator - this indicates check valve failure. In
this case, replace the ozone check valve immediately.
Cauons
3.1 - Follow the instrucons in this Manual carefully.
3.2 - Ensure that the equipment is placed in a locaon where it is at a level above the
maximum SPA water level. Use the xing brackets and x the equipment according this
manual.
3.3 - You should not put the system into operaon if the ozone generator is not well
supported. Ensure the installaon of the equipment in a safe place, which protects it from
the weather, splashing water or excessive heat. When not in use, store the equipment in a
dry place at room temperature. Keep the equipment away from sources of water and/or
moisture.
3.4 - Do not breathe ozone directly. Breathing ozone directly can be toxic, OSHA regulaons
must be respected. Avoid sning or breathing directly over the equipment's air outlet.
3.5 - Do not remove the screws or security seals from the equipment, in addion to violang
and voiding the warranty of the same, there is a risk of electric shock. Remember that this
equipment operates at high voltage even when disconnected from the power supply.
Maintenance Plan Biweekly Monthly Semiannual Annual
Check the Fan Dust Filter X
Check the Pressure in the Circulaon and
Mixing System X
Perform the O3 Generator Checkout by
Soluon Ozone® Technicians X
Table 2 - Maintenance Plan
SSO-O3-##GPOOL01 - User Manual (EN)
..EN
Copyright @ 2020 Ozone Soluon. All rights reserved. This document accompanies the O3 System for SPAs. This document is subject to review.
Merely illustrave images.
Ver2/01-Ver.02
WARNING:
If you noce any ozone leakage, turn OFF the equipment's power supply immediately, leave
the space and only return aer 30 minutes, so that all the ozone in the air is completely
dissipated.

3.6 - Keep the equipment out of the reach of children.
3.7 - Do not cover the equipment during its operaon.
3.8 - Do not insert any objects through the ozone outlet grilles, as this may cause equipment
malfuncons or short-circuits.
3.9 - Clean the equipment with a clean, dry cloth. Do not use abrasive products.
3.10 - Do not open the equipment - High Voltage inside.
Problems / Faults
Warranty
4.1 - This equipment has a free 2 years warranty period, if the equipment fails in normal use,
according to the manual instrucons (determined by the company). To acvate it, you must
present the invoice and the warranty card.
4.2 - The warranty applies to the Ozone Generator System. Consumables such are not
covered by the warranty (check valve, silicone tube, venturi).
4.3 - During the warranty period, the following condions are not covered:
- Does not present the warranty card and invoice;
- Failures and damages caused by improper use or improper repairs;
- Failures and damages caused by transport and fall;
- Failures and damages caused by other external factors, natural disasters or other human
factors;
- Failures and damage caused by water or other types of soluons on the equipment;
- Failures and damages caused by the use of energy or voltage other than those specied;
- Failures by dierent use from what is specied in this manual;
- Damaged or missing Warranty Seal;
- Signs of aempng to open the equipment.
7
Problem / Failure Possible Causes To DO
The Ozone Generator
does not turn on
Generator without power
supply Check that the power is working properly.
Blown Generator Fuse Replace the fuse.
SPA without ozone
Damaged check valve Replace the check valve.
Silicone tubing damaged with
ozone leakage Replace system silicone tubing.
Table 3 - Fault Idencaon
SSO-O3-SPA01 - User Manual (EN)
..EN
Copyright @ 2020 Ozone Soluon. All rights reserved. This document accompanies the O3 System for SPAs. This document is subject to review.
Merely illustrave images.
Ver2/01-Ver.02

Warranty Card
www.soluonozone.com
info@soluonozone.com
Full name Phone Number
Address
Invoice nr. Purchase Date
Maintenance Record
Date of Maintenance
Analysis
Result
Clerk Signature