Somati system SGS-T User manual

Somati system s.r.o., Jihlavská 510/2c, 664 41 Troubsko
IČ: 29260159, DIČ: CZ29260159
tel: [phone], www.somati-system.cz
SPECIFICS OF INSTALLATION SGS-T
02/2019
SPECIFICS OF INSTALLATION SGS-T
Installation shall be carried out according to the standard installation manual SGS, with the exception of the differences
mentioned in this document.
1. GENERAL ASSEMBLY SGS-T (2+0)
(right variant in the drawing)
1 -
leaf 1 = back leaf (by the wall)
A -
bracket of the pulley on the top edge
profile without tensioner
2 -
leaf 2 = front leaf (leaf further from the wall)
B -
bracket of the pulley on the top edge
profile with tensioner
opening direction of the leaf
C -
anchor profile of the wire rope
D -
wire rope holder
E -
telescopic guide
F -
floor guide SGS-T
Somati
system s.r.o.
Somati
system s.r.o.

Somati system s.r.o., Jihlavská 510/2c, 664 41 Troubsko
IČ: 29260159, DIČ: CZ29260159
tel: [phone], www.somati-system.cz
SPECIFICS OF INSTALLATION SGS-T
02/2019
2. SPECIFIC COMPONENTS SGS-T
A. bracket of the pulley on the top
edge profile without tensioner
B. bracket of the pulley on the top
edge profile with tensioner
C. anchor profile of the wire rope
D. wire rope holder
left
right
E. telescopic guide
left
right
F. floor guide SGS-T
left
right
G. wire rope holder 3T on the bracket
of the pulley
H. wire rope holder 3T on the middle
leaf

Somati system s.r.o., Jihlavská 510/2c, 664 41 Troubsko
IČ: 29260159, DIČ: CZ29260159
tel: [phone], www.somati-system.cz
SPECIFICS OF INSTALLATION SGS-T
02/2019
3. INSTALLATION OF THE SPECIFIC COMPONENTS
installation of the bracket of the
pulley without tensioner Aon the
leaf 2 using screws of the top edge
profile
installation of the bracket of the
pulley with tensioner Bon the leaf
1using screws of the top edge
profile
installation of the anchor profile of
the wire rope Con the rail by the
wall above the leaf 1

Somati system s.r.o., Jihlavská 510/2c, 664 41 Troubsko
IČ: 29260159, DIČ: CZ29260159
tel: [phone], www.somati-system.cz
SPECIFICS OF INSTALLATION SGS-T
02/2019
installation of the wire rope holder
Don the leaf 2
installation of the telescopic guide E
on the leaf 1
installation of the floor guide F into
the wall lathing cut-out

Somati system s.r.o., Jihlavská 510/2c, 664 41 Troubsko
IČ: 29260159, DIČ: CZ29260159
tel: [phone], www.somati-system.cz
SPECIFICS OF INSTALLATION SGS-T
02/2019
wire rope
installation
on the gate
leaf 1

Somati system s.r.o., Jihlavská 510/2c, 664 41 Troubsko
IČ: 29260159, DIČ: CZ29260159
tel: [phone], www.somati-system.cz
SPECIFICS OF INSTALLATION SGS-T
02/2019
4. GENERAL ASSEMBLY SGS-T (3+0)
in case of SGS-T (3+0)
the wire rope installation is
repeated on both leaves closer
to the wall
leaf 1(by the wall):
•1x bracket of the pulley
on the top edge profile
without tensioner A
and wire rope holder
3T H
•1x bracket of the pulley
on the top edge profile
with tensioner B
•1x anchor profile of the
wire rope C
(installation on the rail)
•1x telescopic guide E
leaf 2(middle):
•1x bracket of the pulley
on the top edge profile
without tensioner A
•1x bracket of the pulley
on the top edge profile
with tensioner Band
wire rope holder 3T G
•1x telescopic guide E
leaf 3(furthest from the
wall):
•1x wire rope holder D
(right variant in the drawing)