Alien KYDZ-306 User manual

Fixture installation steps:
1.Loosen the dovetail groove locking screw with the hexagon
wrench;
2. The fixture is pushed into the dovetail groove track from the
right side to the positioning position;
3.Lock the dovetail groove locking screw.
Installation steps of milling cutter:
1.Lift up the protective cover, let the protective cover stay on the
top and leak out the screw hole position;
2.Install the milling cutter into the mounting hole, and align the flat
position of the milling cutter with the screw hole position;
3.Tighten the set screw of milling cutter with hexagon wrench;
4.If you want to remove the milling cutter, loosen the fastening
screw and take out the milling cutter downward;
The installation and disassembly steps of the probe are the same
as those of the milling cutter.
Equipment Specifications
Fixture installation Milling cutter installation
Adapter voltage
Maximum power consumption
Package size
Machine size
LED screen resolution
Lithium battery capacity
Spindle speed
Working temperature
Humidity
Net weight
Gross weight
150W
490×320×430 mm
251×421×318 mm
1024×600
55.5Wh
12000rpm
-5~+40℃
10~90%
17KG
20KG
Input:100-240VAC
Output:26VDC
Dovetail groove locking screw
Flat position
Screw hole
Protective cover
Milling cutterprobe
Portable key cutting machine
Quick installation guide
Wuxi Keyoung Electronic Technology Co., Ltd
7-inch capacitive
touch screen
Protection
cover
Led light
Emergency
stop button
Tightening
handle
Identification
window
Crumb tray
Milling cutter
Probe
Fixture

matters needing attention
Emergency stop button Intelligent tooth shape recognition
Cutting collecting box
Instructions for use of cutting collection box:
1.When the cutting waste needs to be treated, it can be directly
pulled out of the lower cutting collection box and the waste can
be poured out;
2.When storing, directly aim at the mouth and push forward.
The distance between user and products should be no less than 20cm.
Instructions for use of emergency stop button:
1.When an emergency occurs or the key processing is finished, the
power supply can be cut off by directly pressing the knob vertical-
ly;
2.According to the direction of the arrow, turn the knob clockwise
about 45 degrees to turn on the power supply of the device.
Instructions for intelligent tooth shape recognition:
1.Insert the key into the fixing hole;
2.On the screen, check whether the key embryo is deviated great-
ly; if it is skewed, the key position can be adjusted left and right;
3.After reading the key sequence, pull out the key directly.
Please read the product operation manual carefully before use;
Wear safety goggles in accordance with ANSI standard when
working;
Do not put your hand into the working area when the machine
is running;
Keep children away from the machine;
When not in use for a long time, please cut off the power
supply;
Ensure that there is no chip residue during packaging and
transportation;
Do not use air jet gun and other tools to clean the chips;
Manufacturer:Wuxi Keyoung Electronic Technology Co., Ltd
QQ:3004280989
WEB:www.kydz-wx.com
Address:5-302,5-301 Huaqing Creative Park,Huishan Economic
Development Zone, Wuxi, Jiangsu
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
Please keep the worktable clean;
This machine has built-in lithium battery pack. Please do not
disassemble it without permission. Keep the machine away
from high temperature and fire source
The machine should be placed in the area of light proof, rain
proof and waterproof.

The following items are included in the package. If it is lost, please
contact your dealer.
Inventory
2.5mm Cutter
1.5mm Cutter
2.0mm Cutter
Probe
2.5mm hexagon wrench
The power adapter
lithium battery
Brush
Clamp K1
Clamp K2
Check block
Host
Product inspection / list
Quick installation guide
2
1
1
2
2
1
1
1
1
1
1
1
1
1
1
Cutting tools（φ1.5×φ6×37L）
Cutting tools（φ2.0×φ6×37L）
Cutting tools（φ1.0×φ6×40L）
Connecting tools
Built-in battery
Machine cleaning tools
Key fixture for vertical milling
FO21/SX9Clamp
Calibration accuracy
Key machine body
Key machine assembly, etc
Name Number Explain
Cutting tools（φ2.5×φ6×37L）
Replace probe / milling cutter /
locking fixture
External milling key fixture /
leveling fixture
Clamp K3
(Optional accessories)
Factory inspection certificate /
packing statistics
（φ2.5×φ6×45L）

This certificate indicates that the product has passed strict
inspection and reached the company's quality standard, and is
qualified and approved for delivery.
This product provides customers with one year's warranty
service from the date of purchase. When warranty is needed,
please show valid Three Guarantees certificate and valid invoice.
Product certificate
Warranty card
Product name: Portable key cutting machine
Product model: KYDZ-306
Inspection date:
Customer name :
Phone number :
Contact address :
Product model :
Product number :
Purchase date :
Wuxi Keyoung Electronic Technology Co., Ltd