SOMFY Roll Up 28 RTS User manual

1Copyright © 2013 Somfy SAS. All rights reserved - V1 - 02/2013
Wirefree Battery Motor
Ref. 5113047A
EN
Installation guide

2Copyright © 2013 Somfy SAS. All rights reserved - V1 - 02/2013
EN
Somfy hereby declares that this product conforms to the essential requirements and
other relevant provisions of Directive 1999/5/CE. A Declaration of Conformity is available
at www.somfy.com/ce. Usable in EU, CH and NO. Images are not contractually binding.

3Copyright © 2013 Somfy SAS. All rights reserved - V1 - 02/2013
CONTENTS
1. Introduction
2. Safety
2.1. Safety and responsibility
6SHFL¿FVDIHW\DGYLFH
3.Wiring
4.Commissioning
4.1. Programming the RTS transmitter
4.2. Checking the rotation direction
4.3. Adjusting the end limits
4.4. Recording the RTS transmitter
4.5. Favorite position: MY position /
Recording MY position.
5.Operation
5.1. Up, Down, My: In roller mode
6.Additional setting
6.1. Favorite position: MY position
6.2. End limit re-adjustement
6.3. Modifying the motor rotation
direction
6.4. Adding/Deleting RTS transmitter
6.5 Erasing the transmitters from the
memory
6.6. Erasing the memory of the motor
1. INTRODUCTION
The Roll Up 28 RTS is a motor specially dedicated to interior applications.
The Roll Up 28 RTS can motorize roller blinds, silhouette blinds and roman shades.
The Roll Up 28 RTS is a battery operated motor, powered with lithium primary batteries
or NiMH batteries with solar pack. The motor can also be powered by a power supply.
Warning : The Roll Up 28 RTS is compatible only with the «Sunis Indoor WireFreeTM
RTS» sensor.
Warning : The Roll Up 28 RTS cannot be used with sealed double glazing.
7. Troubleshooting
7.Technical Data

4Copyright © 2013 Somfy SAS. All rights reserved - V1 - 02/2013
2. SAFETY
2.1. Safety and responsibility
 This Somfy product must be installed by a professional motorisation and home
automation installer, for whom these instructions are intended.
 Before installation, check that this product is compatible with the associated equip-
ment and accessories.
 These instructions describe how to install, commission and use this product.
 Moreover, the installer must comply with current standards and legislation in the
country in which the product is being installed, and inform his customers of the ope-
rating and maintenance conditions for the product.
 $Q\XVHRXWVLGHWKHVSKHUHRIDSSOLFDWLRQVSHFL¿HGE\6RPI\LVQRWDSSURYHG6XFK
use, or any failure to comply with the instructions given herein will invalidate the war-
ranty, and Somfy refuses to accept liability.
6XEMHFWWRWHFKQLFDOPRGL¿FDWLRQV
To avoid damaging the product:
1) Never immerse it in liquid!
2) Avoid impacts!
3) Never drill holes in it!
4) Do not drop it!
1
3
2
4
6SHFL¿FVDIHW\DGYLFH     
In addition to the safety instructions described in this guide, be sure to also
observe the instructions set out in the attached document «Safety instructions
to follow and keep».
Damaged electric products and batteries should not be disposed of with normal
household waste. Make sure to drop them in specially provided containers or
at an authorized organization that will ensure they are recycled.

5
Copyright © 2013 Somfy SAS. All rights reserved - V1 - 02/2013
Plug the battery with the motor supply
cable.
Warning: Do not unplug the
battery when the motor works.
3.WIRING
4.COMMISSIONING
4.1. Programming the RTS transmitter
Press the UP and DOWN buttons
simultaneously on the RTS transmitter:
the shade jogs and the control point is
preprogrammed in the motor

6
Copyright © 2013 Somfy SAS. All rights reserved - V1 - 02/2013
4.2. Checking the rotation direction
Press the RTS transmitter UP button:
a) If the shade raises (a), the rotation
direction is correct: move to the section
entitled 5.3 «Adjusting the end limits».
b) If the shade is lowers (b), the rotation
direction is incorrect: move to the next step.
b1) Press the RTS transmitter MY
button until the shade jogs: the rotation
GLUHFWLRQKDVEHHQPRGL¿HG
b2) Press the RTS transmitter UP button
to check the rotation direction.
The end limits can be set in any order.
1)Press and hold the UP button to move the
shade to the desired position. If necessary
adjust the Up position, using the UP or
DOWN buttons.
2)Press the MY and DOWN buttons
simultaneously and release them once the
shade begins to move.
The up limit is memorized.
3)Press the MY button when the shade
reaches the desired Down position.
If necessary adjust the down position, using
the UP or DOWN buttons.
4)Press the MY and UP buttons
simultaneously and release them when the
shade begins to move.
The Down limit is memorized. The shade
moves up and will stop at its upper limit.
7RFRQ¿UPWKHHQGOLPLWVSUHVVDQGKROG
the MY button until the shade jogs.The end
limits are recorded.
4.3. Adjusting the end limits
1 2
3 4
5
a
b
=
=
b2b1

7
Copyright © 2013 Somfy SAS. All rights reserved - V1 - 02/2013
4.4. Recording the RTS transmitter
After recording the end limits:
%ULHÀ\ SUHVV WKH SURJUDPPLQJ EXWWRQ RQ
the back of the transmitter. The shade jogs.
The transmitter is recorded.
If desired, to set the MY position, move the
shade to the desired position with the UP
or DOWN button then press the MY button
until the shade jogs.
PROG.
4)DYRULWHSRVLWLRQ0<SRVLWLRQ5HFRUGLQJ0<SRVLWLRQ
1)Move the shade away from the end limits.
2)Simultaneously press the UP and DOWN
buttons until the shade jogs.
3)Press and hold the MY and DOWN
buttons simultaneously until the shade jogs
to change from Roller mode to Tilting mode.
5.OPERATION
50RGHVHOHFWLRQ5ROOHURU7LOWLQJPRGH
The Roll Up 28 RTS is designed to work in 2 modes: Tilting mode or Roller mode.
This feature allows the Roll Up 28 RTS to be set according to the type of blind you are
working with.
The Roll Up 28 RTS is set by default to work in Roller mode.
1
23

8
Copyright © 2013 Somfy SAS. All rights reserved - V1 - 02/2013
1
2
3
51.8S'RZQ0\,QUROOHUPRGH
1) To move the shade from a limit to the
RWKHU OLPLW SUHVV EULHÀ\ WKH 83RU '2:1
button.
2) To stop the shade, press the MY button.
3) If a MY position is recorded,To move the
VKDGHWRWKLV0<SRVLWLRQSUHVVEULHÀ\WKH
MY button.

9
Copyright © 2013 Somfy SAS. All rights reserved - V1 - 02/2013
1) Changing the MY position
To change the MY position, go to the
new desired MY position with the UP and
DOWN buttons then press the MY button
until the shade jogs.
2) Deleting the MY position
To delete the MY position, press the MY
button to move to this position and press
the MY button until the shade jogs.
1
2
6.ADDITIONAL SETTING
6.)DYRULWHSRVLWLRQ0<SRVLWLRQ
1) Press the UP button, to move the shade
to the upper end limit.
2) Press and hold the UP and DOWN
buttons simultaneously until the shade jogs.
3) Press and hold the UP or DOWN button
to move the shade to the new desired
position.
7RFRQ¿UPWKHQHZOLPLWSUHVVDQGKROG
the MY button until the shade jogs.
Readjusting the lower end limit
1) Press the DOWN button to move the
shade to the lower end limit.
2) Press and hold the UP and DOWN
buttons simultaneously until the shade jogs.
3) Press and hold the UP or DOWN button
to move the shade to the new desired
position.
7RFRQ¿UPWKHQHZOLPLWSUHVVDQGKROG
the MY button until the shade jogs.
1 2
34
1 2
34
6.2. End limit readjustment
Readjusting the upper end limit

10Copyright © 2013 Somfy SAS. All rights reserved - V1 - 02/2013
1) Move the shade away from the end
limits.
2) Press the UP and DOWN buttons
simultaneously until the shade jogs.
3) Press the MY button until the shade jogs
to reverse the rotation direction.
4) Press the UP button to check the new
rotation direction.
The motor rotation direction is reversed.
6.3. Modifying the motor rotation direction
1 2
34

11
Copyright © 2013 Somfy SAS. All rights reserved - V1 - 02/2013
x3
6.4. Adding/Deleting RTS transmitter
Find an RTS transmitter (A) programmed in
the motor.
Press and hold the RTS programmed
transmitter (A) PROG button or the motor
PROG button until the shade jogs: the
motor is in programming mode.
Quickly press the RTS transmitter(B)
PROG button to add or delete: the shade
jogs and the RTS transmitter
is programmed or deleted from the motor.
6.5. Erasing the transmitters from the memory
To delete all the programmed transmitters,
press and hold the motor PROG button
until the shade jogs twice.
All the transmitters are deleted.
6.6. Erasing the memory of the motor
To reset the motor, press and hold the
PROG button on the motor head until the
shade jogs 3 times.
All the settings are erased.
x2
A
B
A
A
A
B
B
PROG.
A
PROG.
B

12
Copyright © 2013 Somfy SAS. All rights reserved - V1 - 02/2013
7.TIPS AND RECOMMENDATIONS
7KHPRWRUGRHVQ¶WZRUN
9HULI\
7KHZLULQJRIWKHPRWRU
%DWWHULHVDUHQRWGHSOHWHG
7KHFRPSDWLELOLW\RIWKHFRQWURO
7KHKHDWJHQHUDWHGZDLWIRUWKHFRROLQJRIWKHPRWRU
,IXVLQJEDWWHU\WXEHPDNHVXUHWKHEDWWHULHVDUHLQVWDOOHGZLWKWKHFRUUHFWSRODULW\
7KHHTXLSPHQWVWRSVWRRVRRQ
9HULI\
7KHRSHUDWLRQRIHQGOLPLWVGXULQJWKHPRWRUURWDWLRQ
7KHHQGOLPLWVRIWKHPRWRUDUHSURSHUO\DGMXVWHG
7KDWWKHVKDGHLVZLWKLQWKHUHFRPPHQGHGZHLJKWOLPLW
If the motor stops operating normally, the battery voltage may be too low. Replace
batteries.
8.TECHNICAL DATA
Power supply 12 Vdc SELV
Radio frequency 433,42 MHz
Torque 1.1 Nm
Up speed 30 rpm
Down speed 80 rpm
Electrical insulation III
Minimum distance between two end-limit 1 turn
Maximum distance between two end-limit 180 turns
Maximum running time 6 min
Operating temperature 0°C to + 60°C
Protection rating IP 20 (For indoor use only)
Maximum number of associated control 12